No video :(

Un-Squeaking the MAXX FAN Deluxe

Подписаться 2,3 тыс.

Просмотров 1,9 тыс.

50% 1

My MAXX Airfan Deluxe in my Winnebago Revel started to make some very annoying squeaking noises, especially when running on low speed. I took the motor apart and replaced the bearings. It is now super- quiet. This video is the detailed how-to.
I'm pretty sure swapping out the bearings of the fan motor voids any warranties. Proceed with caution.
Bearings are 608Z which I replaced with 6082RS:
www.amazon.com...

Опубликовано:

22 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 21

@ctrawick3 Год назад

As an engineer, I appreciate your precision and attention to mechanical detail. I find your line of thought and meticulous attention to detail, helpful. Very, very good channel of content.

@briangavette6685 Год назад

Your videos are so good. I’ve made many upgrades and improvements on my Revel with your creative improvement and fix ideas. Just thank you…..all of us Revel owners really appreciate the time you spend to share and improve our Revel experience.

@JBLewis Год назад

The "Z" is "shielded", whereas the "2RS" is "sealed" Thanks for the tip! Especially the brush retainer

@twistedfireman 4 месяца назад

Thank you for this detailed video. It sure made my life a lot easier today. 👍🏻

@jknight7265 9 месяцев назад

Than you for the great instructions, I just replaced mine. Definitely could not / would not have done it without your video!

@stevedormaar4102 11 месяцев назад

Thx for putting this video together, great job and very helpful. My experience was a bit different. After I blew out the dust and upgraded the bearings it still squeaked. I took it apart again and smoothed down the commutator with fine sandpaper. This did the trick - we'll see how long it lasts. It would have been great if they had used a brushless motor.

@ifly64s Год назад

Keep these videos coming. They are like going to a Trade School on the Revel!

@7yorks Год назад

Always so helpful; big thanks!

@bobbysnow5478 Год назад

Thanks for the video! Your new bearings are sealed under pressure to keep contaminants out. Good Job!

@threedogsandacamper503 Год назад

Excellent! I look forward to your video on a remedy for the rattling (and banging) noise that the fan unit makes while driving over bumps.

@davidhigginson1838 10 месяцев назад

I just did this yesterday. Squeak gone! I did find that it was easy to take the two screws holding the little plastic piece where the cable exits in and out from the roof of the van with the vent open.

@davidhigginson1838 8 месяцев назад

But it did come back…. Haven’t taken it back apart again. Has yours stayed quiet? Not sure if it was the bearings or just the cleaning. I did get 10 sets of bearings, so will try again when I get the motivation.

@dougbrown6983 Год назад

This was an amazing video …. I have subscribed to this channel because of your detail and well explained process - well done!

@nfri5108 Год назад

another great video, THANK YOU!

@eljeffe991 8 месяцев назад

How is this working out almost a year later? Did the squeaking ever return?

@orange13 8 месяцев назад

so far so good. it still runs as squeak-free as it did after putting the new bearings in

@justinolympia 3 месяца назад

QQ - just wanted to confirm on the bearings.. you used 6203-2RS correct? Thx!

@orange13 3 месяца назад

no.the correct size is 608 which means it has an outside diameter of 22mm, an inside (shaft) diameter of 8mm and a width of 7mm. because the new ones I used have a seal on both sides, they also have a 2RS in their name: 608-2RS. 6203-2RS are way too big, they have an OD of 40mm, an ID of 17mm and a width of 12mm

@justinolympia 3 месяца назад

@@orange13 ok thx. The screen shot you showed had the 603 highlighted.

@orange13 3 месяца назад

@@justinolympia okay, my bad, that was more a reference to the seal than the bearing size