UNI-T UT210E clamp meter overview

Подписаться 4 тыс.

Просмотров 18 тыс.

50% 1

I bought a UNI-T UT210E clamp meter as I needed to check the current being drawn by a suspected duff fuel pump in my Defender. A clamp meter allows you to check the current being drawn by an electrical circuit without having to cut wires and insert a meter in series with the cut cable. A real time saver and potentially (no pun intended) safer. The accuracy at very low current is not great but for the day to day checking I do it is a fine, well but meter.
This video gives a very brief invite to the meter and a few tests are performed as well as some of the useful functions explained.
I bought mine from Amazon and at the time it cost about £35 although it appears they are a little cheaper at the moment. They are also available fromBanggood. Links below.
Link to Amazon:
amzn.to/3iAVvf7
Link to Banggood:
uk.banggood.co...
*Full disclosure. Some of the links above may earn a few pennies for the channel at absolutely no cost to yourself. Thanks for watching. *

Опубликовано:

5 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 32

@cups3 2 года назад

You were 100% right about coating/oxidization on probes. I have that problem on meter leads and brand new two way radio batteries on charger contacts , they look fine but have an "invisible" coating on them. I did to these leads what I have done for years and years (I'm old) I rub them with a slight abrasive . I use Crest regular old fashion PASTE toothpaste , has a tiny bit of pumice in it . Put a small dab on thumb and forefinger and rub , then wipe off make a HUGE difference , continuity taste is immediate .

@MikeMakesIt 2 года назад

Hi cups3 thanks for the feed back. Good to know. I might try the toothpaste trick! Swapping the leads to gold plated ones could be another way to go though not as cheap. Thanks for watching 👍🏽

@Neovo.Geesink 4 года назад

The way you measuring Capacitors is not entirely correct. You are gripping both the probes, making your body a resistor in parallel over the capacitor. Better is to only grab the negative probe with one lead of the capacitor, and hold the positive only on the plastic, and hold the metal tip against the other leg of the capacitor.

@MikeMakesIt 4 года назад

Hi Victor and thanks for your comments. Yes you are entirely correct. I’ve just reviewed my video and I surprised myself I measured the caps that way! I shall be more careful next time. Thanks again, Mike.

@harveysmith100 3 года назад

This exact meter was recommended by Mike over at Britannica Restoration. If you don't know about his channel it is worth a look as you said you owned a Land Rover. I was going to get this meter on Mike's recommendation and you have more than confirmed it.

@MikeMakesIt 3 года назад

Hi Harvey. I've been helped by a few of Mikes videos but not seen the one with the meter. As I said in my video I have found it very useful and it can been seen in use in one of the Defender "Step" videos. I think you will find the meter a great addition to your tool setup, thanks for watching 👍🏽

@whatworkedforme Год назад

I had been looking for something like this for some time but prices put me off; esp for the infrequent use I expected to use it. I bought one of these immediately after seeing that video - primarily for the 2 amp DC ability.

@pidgeonplucker 3 года назад

Just a quick note, to let you know that electrolytic capacitors have a wide value tolerance usually +20% to - 10% of the marked value. It's usually marked on the side of the caps.

@MikeMakesIt 3 года назад

Hi Pidgeonplucker, thanks for your comments. Yes you're right I should have mentioned that when I was testing. Thanks for the reminder and for watching 👍🏽

@emonty62 Год назад

Received, indeed a little gem! Thxs for the review, very good!

@MikeMakesIt Год назад

Hi , thanks for the feedback and of course for watching 👍🏽

@ericnoack Год назад

just bought one. Thanks for the review .

@MikeMakesIt Год назад

Hi Eric, thanks for the feedback. I don’t think you’ll be disappointed, it’s a great meter. Thanks for watching 👍🏽

@seandempsey9396 3 года назад

Uni-t are a good brand They have made a big inprestion in the UK and Europe, all my test instruments are uni-t Exsept for my MFT with ia a ROBIN KTS 1620, I have a uni-t clamp meter a uni-t voltage indicator and a uni-t multy meter I have been using this brend for seven years and I have never had any problems with them, why pay hundreds of pounds /dollars for the likes of fluke mega kewtech and many others when you can get just as good for a fraction of the price from UNI-T

@MikeMakesIt 3 года назад

Hi Sean, thanks for your comments. I very much agree with you, I think the Uni-T brand is a very under estimated brand. The build quality is super and accuracy more than I need. If and when I need another meter I will certainly be looking at this brand. Thanks for watching 👍🏽

@notwrkn2mch 2 года назад

Someone may have posted earlier but I cleaned the probes with a pencil eraser and it 100% eliminated the lack of contact

@MikeMakesIt 2 года назад

Hi Joe, thats a great call! Thanks for watching👍🏽

@whatworkedforme Год назад

Great video Mike. and no waffle or disco music overlaid.. LOL😀

@MikeMakesIt Год назад

Hi Alan, thanks for the feedback and for watching. No music here!! 👍🏽

@marko11kram 10 месяцев назад

Helpful review, Thanks

@MikeMakesIt 10 месяцев назад

Hi Marco, thanks for the feedback and for watching 👍

@playstation2bigs 2 месяца назад

Does ut204+ can read 1 DC Amp ????

@MikeMakesIt 2 месяца назад

The spec says it can read up to 600a DC but at what resolution at the lower end is unclear. Look here: amzn.to/3S5xXjw And here: meters.uni-trend.com/product/ut200plus-series/

@playstation2bigs 2 месяца назад

@@MikeMakesItDoes the red wire (positive) same DC current as black wire (negative) when using UT210E ?

@MikeMakesIt 2 месяца назад

The cables are identical apart from the colour and will carry the same amount of current

@ericnoack Год назад

One thing I can't get my head around .I used this to check amperage in my meter box at the safety switch .It showed I was drawing 2.5 amps on a circuit that I knows carries a lot of power points and appliances ,the dishwasher was on, one of my computers was on, the coffee machine was plugged in at idle, yet it showed 2.5 amps ?

@MikeMakesIt Год назад

It could be right. The computer could draw 30-50watts (depends if it's a gaming machine or not) and the dishwasher could have just been pumping water around that had already been heated but before you started to measure. The coffee machine on idle would only have been a couple of watts. Stick an electric kettle on the same circuit and boil water. I'd expect to see another 2200watts (9amps ish on a 240v supply)

@ericnoack Год назад

@@MikeMakesIt Ill try that cheers and thanks