Unleash the power of the Raspberry Pi 5 - 1TB NVME and Argon ONE v3 NVME case. 

Glad to see this video, a pi 5 and Argon One NVME case are exactly what I asked for for my birthday! I've been using a pi 4 and an Argon One SATA case for some time now, and have been very happy with the setup.

Thanks for the demo, I have one arriving tomorrow. A little hint on the thermal transfer, just peel off one side, apply that side to the component then it is easier to peel off the other side.

well done, concise and clear.

nice thx, just ordered

I have 2 of these for the Pi4 8GiB; My Middle daughter & I built them as Christmas Presents from Santa, She was 10, TwisterPi Installed on 256Gig SSDs. I had my eye on it for a while with the Pi3, Glad I waited a few more months for the Pi4 to come out New Sub; Detroit, Michigan, US

I can't believe Argon didn't use an offset ribbon cable for the PCIE connection. As it is, the SD slot is blocked completely when connected.

Thanks for sharing the video. It would be nice to see some nvme disk benchmarks as well...

Thank you very much

Great video . Well worth a watch . Love these cases

Nice Video

at least you were able to get one, I have been trying since day one and its always out of stock. when I got ahold of someone there they said just wait till its back in stock its been months and no change on stock. :(

They should've utilized the screw holes that are on the raspberry pi to connect the daughter board to.

Hi, thanks for the great video. I have got exactly this rig, but with a Crucial 1TB SSD. After I loaded up the normal RPi OS, I installed the Argon scripts for controlling the fan and power button and everything works fine - fan cuts in and out as the temp rises and falls. However, I got this rig specifically to run Home Assistant OS. So, having loaded the HA OS, all works fine, but because the OS is a hybrid, the Argon scripts won't load and run, hence now way to control the fan etc. I currently have an RPi4 in an Argon M.2 V2 case and use an custom integration "Active Cooling and Active Linear Cooling" addon to control the fan which works brilliantly. Sadly the addon is not compatible with v3 of the Argon case, so at the moment, whilst I can run HA on the RPi 5 in the V3 case, I have no way to control the fan. Any ideas?

Good video but I do have a question. Why would one use the Pi Imager Tool to flash the MicroSD, just to boot the ready to use system up from it and run the Pi Imager or similar on it again with the NVMe drive instead of just flashing to the NVMe directly and perhaps resizing partitions if needed with something like GParted?

No need to reinstall the OS with RPi Imager fresh on the M.2 drive if you've already got it booted from the MicroSD... Just use the SD Copier and copy it directly to the M.2 drive. Power down, remove MicroSD card, reboot, done. Flashing a clean install to the M.2 directly from a clean install on the MicroSD is a waste of time causing you to have to repeat setup steps unnecessarily.

Good video. Could you do one with this case monitoring the temperature during some stress tests?

Great video did you use sudo rasppi-config to set PcI to gen 3?

Hi I like this case, but there is allready option to ((have 2tb w pimoroni nvme duo board)) I would like to find nice argon, metal something case to run it with a fan on top any tips ::-) ??? and do u happen to know whether someone is designing case to fit all thease reguairments including extension board to hdmi & standard charging cable options ::-)

I got mine. Was excited, but now fighting to get it to work. I can't get video out of the HDMI connector. My pi works fine otherwise so I'm at a lost why hooking up the attachment board would result in no video.

Why not flash the OS directly to the SSD with an SSD-dock, why install on the SD-card first?

Hi, thanks for the great video, very instructional esp or newbie like me. Btw, how did you install Webmin into the raspberry pi os (still very new to linux).

Hi thanks for the Video, good info, but where did you get it, no one seems to have any, I'm in the UK

Does the Argon case come with the nvme pcie 3.0 board?

I just got mine today and I'm using the official raspberry pi 5 power supply and it's telling me that it's not powerful enough and restricting the USB Ports.

You need to be able to change boot devices from the raspberry pi itself without having to rely on the Micro SD cards and the operating system. Which you can only do from Raspbian I believe because there's no option to change the boot device in Ubuntu. Having to switch between the SD card is a pain in the ass and time consuming. You should be able to do it from NETBOOT at the very least so that after you're done installing the OS from NETBOOT you can just change the boot Device to the Device that you installed it on because when I've tried installing an OS from NETBOOT it doesn't just reboot into the new OS and the Device you installed it on it just goes back into booting from/to NETBOOT.

hola, se puede acceder a la microsd o hay que desmontar la caja ?

Thanks for the walkthrough. Does the ribbon cable for the drive come with the Argon case?

Did you add a RTC Battery, yet?

Is the wifi connection good using this case

Much easier to use the SD Card Copier tool. No need to reinstall a new OS.

Not the best presentation. Incorrect micro sd procedure, but you made it.