V5 Series Hall joystick drive board installation process, 

it should in my opinion. scuff uses the xbox and sony controller boards and build around them.

@@antjuanoverton1321 The Scuff envision does nnot use a sony or xbox motherboard. Its a completely custom board that scuff themselves make, It just happens to read as an xbox controller on the PC, and it only works on PC

What type of module modifcations did you do?

G unit has better centering, idk why he doesn’t just use the sensors in g unit though…

@@D1S0- could it have less jitter? Just guessing...

@@RustyRaindeerRepairs v3 g unit has no jitter.

@@D1S0- nice, good to know!! I had a batch of the first ones, they have quite a lot...

I don't know if you have found the answer to your question yet. but u can install these sticks in edge controller module. You will need a different calibration board which is v.52 instead of v.5

@@mkp4823 Oh thank you for answering! That sounds good! I was worried there wasn't one that would fit.

I ordered before these were announced and he sent me the new ones.

Skills and tools are important, and good tools make everything easy

I wrecked the first controller I tried it on too. Which part hung you up? I can offer some advice. For removing the old sticks, make sure you ADD some solder to the joints first. This makes reflowing them much much easier with a heat gun as the solder will melt at a lower temp after that. Second, make sure you apply a flux paste to the board, it makes the wicking action a LOT better for the stubborn tiny pins that are way too close to surface-mount capacitors, or the center pins that have the insulator pipe on them. Without flux paste, even if your wire has a rosin flux core, those parts are goign to be harder to heat and coat correctly without ALSO using the iron for so long you end up melting nearby surface mount components. Don't skip the flux. Third, use a small, flat drag soldering tip like he uses in his videos. Having a good iron with temp controls helps a lot too.

I have a lot of experience soldering and if this is your first time I suggest practicing on something you don't care about, first.

I trashed a controller too following exactly what he did. I think it’s maybe because he never explain which connections are actually important and which are just to held the board in place. The middle hole I never really understand.

@@irvintang2751 The four big pins on the joystick off its main corners are purely structural. That corresponds to three large holes on the driver board. The two smaller holes not on the edge of the board go to the microswitch for the R3/L3 button on the joystick. You could pre-solder those connections if you wanted. To make this as easy as possible I would pre-solder the four microswitch pins and the one joystick pin that isn't covered at all by the board. Then you can avoid the two hardest bits of soldering which are the small center holes which are DANGEROUSLY close to surfacemounted resistors and you could accidentally bridge a solder connection to, or melt off entirely. To make the edge soldering easier, pre-tin the back side of the backer board on the center hole. If there's already a little bead of solder there melting it and getting some solder to wick through is MUCH easier. It's a complicated bit of soldering. Having a good iron with temp control makes a world of difference. Also having the correct tip helps a lot. Jun Zeng uses a drag soldering tip in his videos...that's useful for the solder drags he uses in several places, but using a long fine tip for the rest would make a lot more sense.

Yes, but please do not use the yellow module for xbox. I haven't made the adaptation yet

No

aliexpress, it's where I buy stuffs

@@PWDlife Yeah I just spent 5K on joysticks : ) Wish I knew if the PS4 joy sticks would work on the PS5 and Xbox since the driver board corrects the signals

Do you ever solve this

jinfu's mechanical construction has a lower central error

@@junZeng-520 那向你購買的時候會附上那一款電位器呢？

@@redguitar1018 看你的需要

Someone should test that but I don't think it will matter as long as the stick geometry hasn't changed or Sony didn't change the locations of the haptic motor pads to make them interfere.

I haven't encountered it yet, but I don't think it's a problem

I have installed a couple of the V4 versions of this device, you really need either a heat gun or a vacuum desoldering iron. The former is super cheap and easy to get. Just make sure you're starting off with as low heat as you can get away with and be slow and steady. My first attempt I melted some of the plastic/rubber components on the board and had to throw it out. Masking it with foil helps, but I was just using way too much heat. Just apply a little heat to get the solder flowing and then pull on the stick from below with some pliers until it comes away gently.

@@NotMyActualName_ Low melt solder helps a lot, if you mix with low-melt before removing the old stick, it makes it so simple and clean.

@@betabry42 yes, forgot to add that. Definitely makes it easier. I applied a little fresh low melt solder to the pins before heating with the heat gun. The stick came out very easily.

I used a heat gun to remove the joystick, maybe I'll post a video on how to remove the joystick before.

www.aliexpress.us/item/3256805732082103.html?gatewayAdapt=glo2usa4itemAdapt

Hi @@junZeng-520 , thanks for your wonderful work. So you mean if I buy this item from aliexpress you will send V5 of the board instead of V4?

@@nicolasdiaz2694 I have replaced the old version with the new version since December 5th, but I have not changed the description

​@@junZeng-520 link for italy?

the board is more slim and doesn't look bad

@@xgeo23 ...does that matter? It's all in the controller

​@@The_Ballo Evidently the previous version caused a gap in the shell halves when put back together

@@brantwinter oh OK, I wasn't aware

@@brantwinter I saw that video too, I don't think that was the board's fault...that was user error reassembling his controller. The shell has two little white clips in the front you need to close up to prevent that gap. The PS5 driver boards don't come anywhere near anythign that would push against the shell. The slimmer design is probably for the xbox, where the trigger on one side actually contacted the board.

Just my guess about the solder joint, it is to cutting cost to manufacture since there are different pad needed to bridge for different controllers. But your point about the covering up of the feedback motors' pads is valid.

@@hollow314 yeah from what I've seen the same board is used for Xbox and PS4 and ps5 with different solder points. But that still overcomplicates the installation. Just make three versions of the board.

I bet when he sells more that will go and the price will drop. Just an assumption.

From the beginning of the development of the setup, I considered some common Settings to help reduce costs and reduce inventory pressure, if you are involved in the industry, I don't think you want to have three versions of goods in the warehouse.

From the beginning of the development of the setup, I considered some common Settings to help reduce costs and reduce inventory pressure, if you are involved in the industry, I don't think you want to have three versions of goods in the warehouse.

Currently on sale on Taobao and AliExpress, Amazon is still preparing.

@@junZeng-520 plz give me link to buy your product on taobao

兄弟我在淘寶上找不到你的連結可否發一下或者告知要搜尋什麼關鍵字

@@redguitar1018 霍尔摇杆驱动板

@@junZeng-520 is it available on Amazon now?

He sells board-only on his ali express but only in quantities of 50. I assume for people who want to sell this install as a service.

@@NotMyActualName_ No, I have retail, too. I updated the inventory. You can check again

It filters out the jitter the Hall effect produces and helps with calibration of the Hall effect sensor. It improves the circularity of the joystick as well

I have started shipping the new version, but the description of the product is not switched.

@@junZeng-520 cool! I will place another order

@junZeng-520 you only have the PS4 in stock. That's the same exact board as the PS5 right? I just have to wire it differently?

I've not noticed that it does but i'm not really that sensitive to it. Intiuitively though it MUST introduce SOME amount of lag because the board is essentially post-processing your data inputs. That said it's being done with a dedicated chip so it's almost certainly sub 1ms

从十二月五日起发货的订单，我都是发货的新版的。我需要2-3天将页面描述变更过来。

@@junZeng-520 好消息！！謝謝你！！

it comes with the kit when you buy it

For people who do repairs and play guitars, I think having a little bit of nails makes everything easier.