Elite II Install Hall joystick demonstration。

Подписаться 1,2 тыс.

Просмотров 5 тыс.

50% 1

Hello friends, many friends asked me if it can be used on the Elite 2 controller, and my answer is yes! Due to the complex structure of the control, it will be a little different from ordinary installation. I think there are mainly four points to pay attention to:
1: The left joystick needs to be tilted a little instead of being installed directly.
2: The plastic of the LT button will press against the circuit board, so you need to use a knife to cut off the conflicting part.
3: The LT trigger sensor needs to be removed and then slightly raised when reinstalling.
4: I used an ordinary joystick. The threaded Hall joystick will have size incompatibility issues, so please use it with caution.
The above is what I think requires extra attention. Other than that, it is no different from ordinary XBOX controller installation. After replacing it, you will get an excellent center dead zone, far better than the original joystick!
There are some other things. Due to EU procedures, AliExpress has removed my products from the EU. I am still preparing for the procedures and will restore them as soon as possible.
Installation manual: drive.google.com/drive/folder...

Игры

Опубликовано:

9 янв 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 75

@ECPer 5 месяцев назад

I just received the sticks and boards from Aliexpress. Should they come with diodes? Do you have diode part number that I can get myself?

@Ferg.0 Месяц назад

Well, if that's how much solder you put on there no wonder it's so damn difficult to get the original joystick out of the PCB

@anthonycapella8928 21 день назад

Is there a reason you do not connect the left trigger hall effect Sensor to the LH calibration board, like you do for the regular Xbox controller?

@IMDYT420 Месяц назад

I bought some elite series 2 hall sticks off alie express, would I follow the same steps in this video or is there any differences in installation with the elite 2 sticks? Also what’s the point of the insulation in the middle pin?

@iXiwar Месяц назад

Hello, thank you for your video i woul like to do it too but as i search on Aliexpress, i only find hall effect for Elite 2 without board ! Do you have a new link for your's ?

@mnurrreza 5 месяцев назад

dude, what you have done is an amazing feat. and I am grateful for you to have achieved this. but instead of having your board soldered separately, do you plan, in the near future, to have your module to be included with the joystick module itself? so that the user could just solder it at once. I don't understand the engineering or the licensing aspect of such feat, but do you plan on doing that in the future? cheers

@tonka8080 2 месяца назад

Due to the tight clearance of the thumbsticks in the controller housing it would cause issues with rubbing you'd have to find either a low profile module or a modded shell

@Inv1ng0 5 месяцев назад

Hello !Where can I buy it ? Aliexpress link pls !

@YEYO7140 5 месяцев назад

Amazing work, I appreciate all your work. I had ordered a few of this products they work loke a charm. Question, Are you working on supporting the threaded hall effect joystick? It would be amazing to still have all the elite series 2 features. Thanks for your time 🙏🏽

@junZeng-520 5 месяцев назад

Threaded joysticks can also be used, but due to dimensional errors, friction can occur between the joystick metal cap and the plastic housing. Thank you for your attention

@YEYO7140 5 месяцев назад

Thanks!

@zznothinzz 5 месяцев назад

There is a k-silver module specifically for elite 2 with adjustable tension

@YEYO7140 5 месяцев назад

@zznothinzz I know, but for peace of mind, I would like to integrate this board for calibration and frequency interference between the joystick and the magnetic thums stick.

@FrostFRFX 4 месяца назад

@@zznothinzz Could you link me it?

@Imm0rtal49 17 дней назад

Does this apply to the Xbox wireless control as well?

@woollendisc311 2 месяца назад

What diode are you installing and where can it be bought? Or does it come with the kit?

@Tr4shBerry Месяц назад

Comes with the Kit

@Marekk_2k 5 месяцев назад

Hi. Could you explain to me why your joysticks are not available for purchase in Europe, or more specifically in Poland? Your joysticks used to be available for purchase. Are you refining the current version or is it financially unprofitable for you?

@xcas9 5 месяцев назад

You can read in his notes in the description. " There are some other things. Due to EU procedures, AliExpress has removed my products from the EU. "

@TheModgenius 3 месяца назад

So question. For the sensor did you simply use the same sensor and moved down to cover the ordinal pins ?

@victorlowe 2 месяца назад

Its same one he showed in first 40 seconds that he removed

@TheModgenius 2 месяца назад

@@victorlowe thanks. I have learned though with trial and error if you don’t have a big enough spacer under the sensor that the short throw trigger will not register. The same goes for the right side

@Mossige89 4 месяца назад

Does the metal back paddles affect the hall joysticks with this board?

@ruch-oporu 4 месяца назад

No, paddles workings normal... 👌

@Mossige89 4 месяца назад

@@ruch-oporu Yes paddles would work normal, but I tried the orange hall effect joysticks without these calibration boards, and the metal paddles would pull on the right joystick, so it would center different when they were off and on

@1sneeze 5 месяцев назад

Is there any way in the future to not be required to have an extra pcb to be able to use the sticks? Like an all in one system with no soldering just plug and play

@KennyMinigun 5 месяцев назад

Apparently he only produces the boards. Sticks will Hall effect sensors are sourced elsewhere (like K-Silver). But that would be a wonderful solution if it all was integrated. Marius Heier seems to be working on something like that, but he has nothing for sale yet.

@TheWebstaff 5 месяцев назад

I'm not sure there is the volume of sales to justify the cost.

@junZeng-520 5 месяцев назад

@@KennyMinigun In fact, I also provide joysticks, and it is not expensive. Nothing is more cost-effective than Chinese production.

@junZeng-520 5 месяцев назад

@@TheWebstaff In fact, customers who do not have high requirements for the use of joysticks can not use this solution. My solution is to pursue the ultimate return effect and the external dead zone can be adjusted.

@TheWebstaff 5 месяцев назад

Are they the same hall sensor assemeblies for the elite one?

@junZeng-520 5 месяцев назад

Yes, but the elite generation will do it a little differently. I'll make a separate video.

@sudharshanmanneru3613 5 месяцев назад

Why is there no delivery for india??

@scottcerato4473 3 месяца назад

Do these boards work with normal xbox one controller and series x ?

@ruch-oporu 3 месяца назад

Xbox one and elite 2

@Lemongeko 5 месяцев назад

😃😃😃😃

@alexklaus2778 4 месяца назад

So I treid it the exact same way. Whe I tested, the sticks where frozen to one side ( top left-left stick / bottom right -right stick). Anyone knows why that can happen? After installing the original sticks back on, it also behaved very weird. My guess is, that I damaged the PCB but maybe someone has another idea?

@TheModgenius 3 месяца назад

Photos please

@tonka8080 2 месяца назад

So why exactly does the module need to be tilted?

@Tr4shBerry Месяц назад

If is not tilted the left thumbstick will not be centered with you reassemble.

@jorgecazares6016 5 месяцев назад

If I don't put the plate that goes under the joystick, what happens? Does it work without putting it on?

@sudharshanmanneru3613 5 месяцев назад

It makes it easier to calibrate and has no jitter unlike the orange ones( which doesn't need the calibration board).

@jorgecazares6016 5 месяцев назад

@@sudharshanmanneru3613 And which ones would you recommend more, blue or orange? Thanks for answering me

@sudharshanmanneru3613 5 месяцев назад

@@jorgecazares6016 the orange ones are easy to solder as they don't have any pcb but they very hard to calibrate, the blue ones are hard to solder but very easy to calibrate, if you are good with soldering then go with the blue one's, even if you are not good with soldering try contacting someone repairs controller and ask them to solder it for you. The orange ones are very hard to calibrate so i prefer jun yeng blue ones

@thesilencer8074 7 дней назад

@@jorgecazares6016 The PCB would also prevent the magnet of the left trigger from disturbing the hall effect potentiometers of the left stick. It is therefore more than recommended to use these PCBs regardless of the colors chosen.

@twall667 3 месяца назад

I put a set in my elite series 2 & and afterwards, the trigger jutter & the sticks spin crazyly. i think i hurt the board some how... this is my 3 controller. The first 2 went perfectly...

@Delaware-lk5vk 3 месяца назад

I have exactly the same problem.. I think these Analog sticks from Aliexpress do not work for ELITE 2 Controller ! Do not buy them !

@twall667 2 месяца назад

@Delaware-lk5vk I figured it out its the ones with both blue hall effect sensors off aliexpress. I ended up using the other ones I have off aliexpress one blue one green sensor & now my elite 2 works perfectly

@thesilencer8074 7 дней назад

@@twall667 Don't the magnets contained in the Thumpsticks interfere with the hall effect potentiometers? It's a possibility that makes me wonder if I'm doing the right thing by replacing mine with this type of material.

@twall667 7 дней назад

@thesilencer8074 no not at all! That is what the pcb is for it connects to the trigger and corrects the movement of it.

@thesilencer8074 5 дней назад

@@twall667 Ok thank you for the answer. I searched for quite some time and saw everything and its opposite as an answer. And the same for the calibration, each time they were done without the sticks screwed onto them so that it was impossible to get the answer that way either. I have an official classic Xbox Seris X/S controller and I told myself that since I was going to change the sticks and that they are the same size, I might as well install sticks with more options like those of the elite series 2. I would obviously buy the screw-on magnetic caps that go with it. And besides, I have another question to ask you. Do the sticks you bought also have the spring tension system? Because if that's not the case, I might as well take Elite 1 magnetic sticks and caps.

@kuclaw5406 5 месяцев назад

Where is link to your offer ?

@junZeng-520 5 месяцев назад

www.aliexpress.us/item/3256805732082103.html?gatewayAdapt=glo2usa4itemAdapt

@MassimoFantinato 5 месяцев назад

@@junZeng-520do you ship to Europe?

@tecladin 5 месяцев назад

what are the costs involved in making a usb type c charger for the ds4? I would certely buy some

@tonka8080 2 месяца назад

I actually have some. Not sure where you are from but I'm in Texas

@XEOSIE8786 3 месяца назад

Bro so does this method work witht he new xbox Elite series 2 thumbstick instead of normal u using

@Tr4shBerry Месяц назад

Works for any elite

@connorkenway2211 5 месяцев назад

1:42 could you please tell me why must do this ?

@junZeng-520 5 месяцев назад

This is the experience of installation, if you keep the vertical installation, after installing the housing, it will be offset

@connorkenway2211 5 месяцев назад

29:13 : The LT trigger sensor needs to be removed and then slightly raised when reinstalling. im using the yellow/black joystick and havent raise the sensor yet, but already connect the board to the sensor. The board didnt compensate for the trigger. Are there any wrong ?

@Big_Jus 3 месяца назад

Does the diode that goes onto the board come with the kit?

@Tr4shBerry Месяц назад

Yes. When you install make sure it is installed in the correct direction (as seen in the instruction) otherwise the calibration will not work properly

@TheNoNameOneManShow 2 месяца назад

Am I supposed to have these diodes on hand ?

@ccdarin520 5 месяцев назад

do you have any link for taobao?

@junZeng-520 5 месяцев назад

YES

@ccdarin520 5 месяцев назад

@@junZeng-520 give me the link

@vitaliy9626 5 месяцев назад

@@junZeng-520please give the link on taobao

@TheNoNameOneManShow 2 месяца назад

Can someone please send me the right link ?

@Sytron- 2 месяца назад

Looks like a S4 SMD Diodes but not sure about the third one.

@cesaru3619 3 месяца назад

LOL!

@giggity4670 Месяц назад

A bit more work then i thought it would be and on my elite controller the solder is strong and does not like to melt even when my iron is at 250c. And for god sake cut your nails looks horrible to see.

@Tr4shBerry Месяц назад

For desoldering the old sticks, Microsoft uses a higher melt point solder. Need a MIN of 400c

@thesilencer8074 5 дней назад

Nails are used in this type of work. It is for practical reasons that they are so long, just like those of certain guitarists who use them as a pick. As someone who tinkers a lot, I often use it to catch small screws that have taken refuge in corners. It can be used as a small screwdriver for adjusting certain electronic modules. It also helps protect fingers from burns for certain welding jobs.