No video :(

VCarve Pro Moulding Toolpath (Revised)

Подписаться 4,8 тыс.

Просмотров 21 тыс.

50% 1

In this video, we take you through the steps of creating one-of-a-kind moulding using the Moulding Toolpath in Vectric VCarve Pro.
The CNC portions are at 10x speed with much cut out for the sake of viewing time, actual cut time for the moulding was about 4 hours.
Bits used include a 1/16" Ballnose for the moulding and 1/4" Endmill for the cutout.
*This video was revised from the original to take care of problems with the voiceover and audio quality

Опубликовано:

5 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 18

@CLCLTD 4 года назад

Your very good at talking us through your videos, would you consider doing a series’s of operating the software from beginner level

@EverwoodCreations 4 года назад

Thank you so much for your kind words! I have been wondering if there was an interest in the most basic levels of using the software, I'll definitely be looking in to it.

@RockhollowCNCServices 3 года назад

@@EverwoodCreations Yes please!

@shaneclk9854 10 месяцев назад

4 hours my word

@damienmcnally4859 2 года назад

Thank you!

@brooksnelson7870 Год назад

Question, while I watch your video you have the work piece setup for a width of 25” in the x, although when you cut the piece you are cutting the length in the y? Did you have to re tool path for that direction?

@aimanhakim3995 Год назад

how long time you take for 24” mould to be finished? May i get your advice on how im going to improve the speeding on cnc machine

@ArvindKulkarni9 Год назад

Can you make a video for carving molding on rectangle rather than just straight line

@jazzjohn2 4 года назад

I cannot get the tabs to appear in the 3D view. I can see the bumps in the toolpath, but not the tabs in the 3D view. Using ver 9.518

@jazzjohn2 4 года назад

Figured it out. I needed to remove the vertical sides from the profile.

@EverwoodCreations 4 года назад

Glad you got it figured out! Your comment may help others with a similar problem.

@treslongwell1332 11 месяцев назад

what is the length limit?

@rita-cristinapista5222 4 года назад

Hi, I am trying to do the toolpath, but nothing happens after I select the profile. Is there any specific key that I have to press, or just select them with the mouse?

@EverwoodCreations 4 года назад

If I am understanding the question correctly, while in the molding toolpath panel, you want to first select your driverail, hold the shift key and select your profile. The last vector chosen will be used as the profile if you are doing multiple rails. Hope this helps!

@woodmaninwork2107 4 года назад

Halo,this video is helpfull for me (:,and what folder you used?

@EverwoodCreations 4 года назад

I'm so glad you found it helpful. I'm not sure what folder you are referring to, can you give me more to go from or a timestamp from the video?

@cliffart7398 4 года назад

I don't recall the tool you used but assume it was a 1/4 ball nose?

@EverwoodCreations 4 года назад

For this molding set I actually used a 1/16" ball nose because the small details at the top required it. I have used 1/4" ball nose successfully on molding that is less intricate though. I did use 1/4" end mill for my clearance tool.