Vevor Melting Furnace: Review Setup and Tips - Is it Worth Buying?

Подписаться 121 тыс.

Просмотров 76 тыс.

50% 1

With many different manufacturers of melting furnace kilns, how to choose which one to buy? I was happy to receive a review model of the Vevor melting furnace to test out and share with you, and I've been wondering as I'm sure many others have; How good is it? Given that it costs almost the same as building your own would, is it actually worth buying? Find out here!
Use this code for 35% off a 10kg melt furnace until the end of November! (Please note: it only works on the 10kg version, and only on amazon.com)
5MBUJNLT
Get the melting furnace here: amzn.to/3VjP1BC
Wire stripper I use: amzn.to/3sirg18
The motorized stripper: amzn.to/3y0JMuQ
The wire cutters I like: amzn.to/2T6j3OW
The grips I recommend: amzn.to/2QCJmYl
(If you make a purchase on amazon through the links above, a small amount of what amazon makes on the sale is shared with me. It's a great way to help support my channel, at no additional cost to you. Even if you buy something other than my tool recommendations!)
Please like/share this video if you enjoyed it, and subscribe to thubprint!
/ @thubprint
I love mail! You can send me some here if you like:
Thubprint
PO BOX 99900 RF 764 740
RPO WESTBROOK
CALGARY AB
T3C 1B6
/ thubprint
/ thubprint
Music: bsmith - Industrial Scrap

Опубликовано:

6 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 234

@CharlesStevens-vi7ky Год назад

I am glad you mentioned rigidizer and the risks of using uncoated ceramic wool insulation. For the home builder there is a pre coated product available and I would hope the manufactures would start using it.

@gravitybear Год назад

Superb! I always enjoy your product review vids, even for products I don't intend on purchasing. Your thoughtful presentation is always welcome, and the videos are fun.

@TheDoItYourselfWorld Год назад

I am just getting ready for my first aluminum melt in my Vevor 6kg furnace. I have it all put together and ready. Cant wait to get melting.

@lorrainemcdonald7332 Год назад

Always a good day when Thubprint puts out a video.

@thubprint Год назад

Thank you!

@JoshBeq Год назад

I got the exact same Furnace and love it. Meets all expectations for my first one.

@adamdaley8090 Год назад

Nice addition to the program. Remember to preheat your molds to avoid steam explosions. And always wear a respirator please.

@thubprint Год назад

10/4!

@adamdaley8090 Год назад

@@thubprint I watch BigSparksD melt a lot of stuff. You and him are my scrap/melt Friday routine.

@vevor.official Год назад

Thank you for the great review! We’re so happy you loved your experience and can’t wait to have you back in the future.

@jpansamerica Год назад

This is so exciting, I was hoping you were eventually going to get something like this. can't wait to see how the bars pile up

@mollynakamori Год назад

I am so happy for you that you got your new toy! Looking forward to a bunch of videos of you making cool, weird stuff.

@thereaper310 Год назад

Thanks for the video. Great info. Mine is in the mail along with that ceramic wool rigidizer you recommended. Keep up that good work brother.

@MB-bt9km Год назад

Excited to see you start the metal stack like bigstackD!

@its_marc Год назад

Ooh new toy day! Happy for you mate, looks fun.

@hipyowowtop Год назад

Opinion from a scrap yard’s perspective: Would not suggest creating personal ingots if you’re looking for profit on your scrap. You will have a tough time selling your material and likely downgrading your metal. You won’t be able to certify the metal in your ingots. Smaller yards won’t be able to verify the chemistry and although larger operations could run their tests they will likely downgrade knowing quality won’t be consistent from a garage smelter. Melting is definitely fun, would only suggest if you’re just looking to create cool content online and not looking to profit off this metal.

@jayc8180 Год назад

I agree. Eventually you will find someone that will buy them but it’s tough. Most yards won’t especially if they don’t know you. Surprisingly there’s people that will buy them on eBay. Even at crazy premiums for some reason. Personally I think a few 5 gallon buckets of bare bright solid core is just as pretty😂

@joeldobbs7396 Год назад

I can verify this, I worked at a foundry that processed lots of aluminum, every batch was sparked on the spectrometer with the sheet included with the ingots. One exception was a nail company that paid for aluminum ingots for deoxidizing their alloys, but they only wanted extruded aluminum. Lead would be another exception, we melted down anything from poo pipe to used medical isotope casks for mill anchor. Hahaha, Zinc fires are great indoors, nothing like coming in to a dusting of snow. Oh, and slag is from smelters, what you skim off is called dross.

@joshp6061 Год назад

eBay is huge exception to this, copper melted into ingots (especially when finished/polished) sell for minimum $10 per pound and even up to $50

@thubprint Год назад

Oh I’m aware, you’re 100% right all the way down 😁 I’m only doing it because it’s a fun visual representation of the content recovered from specific scrap items (and the internet seems to enjoy scrap melting vids)

@goodtimeeric Год назад

If you're looking to profit, don't sell your copper and brass to the scrap yard.

@fragnicht1734 Год назад

Got this one for my birthday, it looks very well working

@4speed3pedals Год назад

If the lid does burn out at the opening and enlarge, I think cutting a larger hole (square for ease or round if you are up to it) and replacing it with a piece of stainless steel sheet larger than the hole with the exact same size center hole, held in place with solid steel rivets or steel bolts would end future issues. Use a slightly thicker piece of stainless steel if available. I would imagine that as the original steel erodes, the insulation will also. To cut out the patch, an electric or an air powered "zizz wheel" (cut off tool with a thin a thin abrasive disc, some people call it a "death wheel) cut off tool. Just make sure the blade is in good condition, worn evenly, etc. Thanks for posting this. I just got a notification from Vevor about their stainless steel 12KG model. It looks like the same tongs are supplied.

@livvyweimar7362 Год назад

This is pretty cool. Looking forward to seeing you melt many things lol

@gtdude2883 Год назад

Awesome review, thanks for posting the review.

@BITTYBOY121 11 месяцев назад

Thanks Man ! - Great demo and review ! - Well done bro 👍👍👍👍👍

@jakkll Год назад

I just got mine yesterday and found this video to familiarize myself with it. Thanks for the tip on sealing the ceramic. I did notice my furnace lid has 3 ea 3/4" x 1.5" tabs to hold the lids insulation in. No need for screws in my case. Good job on the video.

@Typical.Anomaly 5 месяцев назад

How'd it hold up? I have one in my eBay cart, waiting to pull the trigger.

@jakkll 5 месяцев назад

@@Typical.Anomaly still love it but you should know it is not a daily burner. I use it very infrequently. The ceramic will need replacing soon and I've only put maybe 10 burns on it. The joint at the burner flange gets red hot too indicating that it will be a failure point in the future. Lastly, the burner does "flameout" or becomes too o2 rich (or gas rich, can't tell) and loses its jet so I have to reset the fire. That's easy to prevent though by making sure the pressure at the tank is high enough and just babying the mix with the sleeve until you get familiar with it. Good furnace for the money though. I'm still satisfied cause I know what it can and can't do. I've melted copper but not gotten much higher than 2400-2500 degrees. Will have to custom build for steel if I want 3-4k. Or buy a 10k dollar unit lol.

@TheUltimateRecycler Год назад

Nice review Thub! At least you'll be able to keep your shed warm now! 😉😊

@cocopufer5667 Год назад

Nice review, now that you have a proper melting station I cant wait to see you start melting stuff - imagine a giant stack of those bars

@strikebrofishing Год назад

Love the product rating at the end 🤣

@itsjustme356 6 месяцев назад

very nice to see a review , just got mine

@jeffarto8340 Год назад

you need to heat the molds up as well. or the bar will have spots and cracks, and will splatter.

@jamestran347 Год назад

you mean warm up the mold?

@JJROGERS41 5 месяцев назад

I bought mine based on this review. They have improved the lid to keep the insulation in. But the tongs and the gloves are crap as you say. Great fun! And thanks!

@joshp6061 Год назад

A full ceramic mortar coating is better, and you should always preheat your molds to prevent explosions and get a smoother cast. You can always remelt if you get a lot of holes or a bad cast

@DIEmicrosoft 7 месяцев назад

You Should Preheat Everything. Thermal Shock Hurts.

@jamestran347 Год назад

thanx thubprint, very well spoken and great explaintion, spot on!!😀😀

@theodorelueker5057 Год назад

I look forward to seeing you out in a dumpster and find something you want to melt then run home as fast as you can strip down what ever it is you are melting and get the melting process started later experiment with different molds. This will be a cool addition to your channel.

@thubprint Год назад

That’s a really neat idea! Just a solid one-day challenge from dumpster diving to ingots. I’ll be sure to give it a go!

@timrockman7 Год назад

You need a bimetal pyrometer to monitor temps. Drill a hole 3/4 upper furnace hight and use an angle so the tip 4" of the thermocouple is to the side of the fiber insulation. Use Sodium Silicate mixed with Kaolin powder as an adhesive to seal the probe hole. It makes a decent mortar also. I built about 20 furnaces like yours that could melt 200 pounds of copper.

@billymacktexasdetective5827 8 месяцев назад

The average Joe screwing around on the weekend in their garage doesn't need to monitor temperatures...

@Slangevar333 5 месяцев назад

Thanks Tim, I just got one last week and want my first firing, melt and pour to go as well as it can. I have a pyrometer (for firing a pottery kiln) but haven't yet considered applying it to this task. Your install description is helpful. I made cast sculptures 40 years ago using wax investment and also sand casting process. I don't want to overheat brass and do want to monitor the temperature to be able to plan for time and to calculate gas usage. The sodium silicate & kaolin combo for sealing up the kaowool surface sounds like a good treatment and will apply that. I have used a water- alumina - kaolin mixture to keep kiln shelves clean. I think I may add some alumina to increase the heat durability of the coating and reduce the possibility of cracking, what do you thinks?

@garyoliver9987 Год назад

Very cool i have been thinking about getting one of these.

@madchewychunk9833 Год назад

Sending love from Minnesota, Big inspiration to scrap thanks really exciting hobby!

@markgobel9187 Год назад

Thank you for this great video, you encouraged me to buy a vevor melting furnace. Just a question with which spray did you spray the inside of the oven and harden the ceramic wool?

@MrRichardCopeland Год назад

Havent watched this one yet but stoked to see your new setup up, no word of a lie, I have been watching your pouring videos all morning and I was thinking you needed a new setup, Like bigstackD Casting. Then Boom new video, new setup. Update: great video, I think the porous copper was from moisture in the mould. I tried the Discount code with no luck

@thubprint Год назад

Another bounce on the discount code.. that’s annoying. 😕

@MrRichardCopeland Год назад

@@thubprint no worries, keep up the excellent content

@sarlaccstapeworm990 Год назад

Mine JUST got to my door!.... Hence me coming here to see what you had to say about it! I feel a lot more confident in the purchase now. I only paid about $120 for the EXACT same setup. With some of the projects that I have in mind to do, I feel like it was money well spent now. All I need now is another pair of tongs, maybe a couple of different sizes of crucibles, and a couple of different molds (not to mention better gloves)... Thanks for the review buddy! It was really helpful! 👍

@msoul3248 8 месяцев назад

Thank you for your reply. I am in the same boat. Where did you go for your crucible, mold, and tongs purchases?

@sarlaccstapeworm990 8 месяцев назад

@@msoul3248 If I'm not mistaken, I think I got the extra crucible straight from vevor's site (for about $40). I can't remember who makes the extra pair of tong's that I got, but if I'm remembering right, I just shopped around on Amazon until I found a pair that was a little more affordable than what they were going for on Vevor's page. The ones I wound up getting were about $35, but they were $60 - $70 everywhere else I looked. 👍 (P.S. Still haven't got the molds that I want yet... been using muffin pans and stuff like that. lol)

@startide Год назад

That's a nice review video, thanks for that. Any recommandations on the sealant ? More specifically brands cause that stuff is certainly called by a different name over here in france, and I wanted to be sure I got the right stuff

@aarongreenakacavemonster904 Год назад

Love your channel bro

@CaptainAaron Год назад

awesome!! that thing will heat up your garage very nicely too

@dpuboc1 Год назад

I couldn’t believe this product could be good at the price.I am an experienced sculptor used to foundries so would be aware of the H&S precautions and would feel confident trying this out. Especially with the recent innovations in high temperature silicone moulding it’s very exciting. So personally I thank you. Anyone who is not fully aware of all the risks should invest in studying all the issues and processes involved first. This baby is not a toy and when things go wrong they go wrong big time!.

@AndrewMcGowan-vu2cl Год назад

did you temper the crucible first? slowly heat in a domestic oven to dry it out. then heat in furnace to highest temp you plan to use it at, and hold this temp for around 20 min. seems to glaze the crucible and make it last a lot longer without the flaking you saw. experiment with some casting, its great fun!

@nathanking2484 Год назад

Thanks for a great video

@msoul3248 8 месяцев назад

I am glad you posted this video. I am new to this and debated making my own or possibly a purchase like the devil forge(before I saw this). I have most if not all the items needed except the batting and the burner to make. I have noticed many saying “its not worth it to melt down” or “your scrap yard may not take it” but I find my need is a little more of having large sized buckets of copper, aluminum, cast(fan motor ends) that I would like to convert to smaller stacking units. I need more info on useable sized quality crucibles (where to get) and tongs and it would be nice if anywhere had a forum where discussion on the topic could be accessible. Thanks again👍🏽

@thubprint 8 месяцев назад

I know Reddit has a sub filled with good (and bad) advice! I noticed a lot of the people there strongly discourage buying a melting furnace because it’s “so much cheaper” to build your own. And while I am a huge fan of the DIY approach, I did the math and I think it costs about the same if you have to go buy all the components to do it

@msoul3248 8 месяцев назад

@@thubprint yes, while the model you evaluated was out of stock, the next model up with two burners (i think an extra $90) was available (it may not have the gloves but I have that taken care of already). You have more experience at this so where do you get your molds?

@vinnienowhere1015 Год назад

Do you have a different buyer for the metals than a scrap yard? How much of a premium do you get vs scrap yard prices? Great vid thub!

@johngalt166 Год назад

Excellent video. where did you get the refractory seal you use at minute 2 in the video to seal the blanket?

@6980869 Год назад

thumbscrew hose clamps are way cooler(easier to use) than conventional hose clamp fasteners, definitely the way to go. At least u got a solid torch to heat up those tongs to bend it. Thanks for sharing your thoughts and observations on this. Aloha

@iceman125971 8 месяцев назад

Harbor freight has those kinds of hose clamps btw. I like them for things that get removed a lot. Like radiator hoses.

@Vault57 5 дней назад

9:34 Actually, the ceramic wool will degrade with each subsequent firing without a well applied even coat of rigidizer or appropriate coating. Even the coating will eventually break down and expose the wool. It needs to be periodically maintained. Ceramic wool has been compared to asbestos due to some similarities with those minerals. Your assessment of this product was pretty spot on. Some good suggestions for minor upgrades that would improve the product without terribly impacting the cost. Shoot, they don't even need to make the changes. Just put a slip of paper in the box with your suggestions and let the DIYers do it themselves.

@PlatoonGoon Год назад

cheers, stay learning.

@ladigger362 Год назад

Decided to get the wire stripper you use off your web site .I like it better than the china strippers with motors.I can use this stripper in the field with my cordless drill .Thanks enjoy the channel .

@gene80shits Год назад

brilliant.. sound advice

@williammikell2210 Год назад

KOOOL! Now you need a Panda stamp.

@mikemuzzell5167 Год назад

Vevor eh! They got their hands 🙌 in everything. Just bought a distillery kit from them. Haven’t used it yet. I also like melting. Intriguing 🧐

@chrisveejay Год назад

I have just started scrapping after watching your videos. Doing it using my old car now.. I think this is way beyond me for now. I would like to see a video of how to use the grinder for idiots (like me) to cut metals. Maybe the types available in the market. The do's and dont's too.

@matt2244 Год назад

lol that rating system is amazing!

@thubprint Год назад

😆👍

@timrockman7 Год назад

Preheat your cleaned molds. The porosity was created from traces of moisture or something that gassed out from the heated molten metal.

@billymacktexasdetective5827 8 месяцев назад

Traces of moisture did not create the porosity. Molten metal will cause moisture to violently expand 1700 times its original volume into steam. An explosion that won't go unnoticed... The porosity is caused by the failure to degas the molten metal prior to pouring...

@itsfour20 7 месяцев назад

Hey did u find that the double valve to the propane tank , the male connect is longer then the average male pol connector

@cbailor1 11 месяцев назад

I'm looking to be purchasing a smelter soon and I'm just curious as to what size yours is it seems close to the size I'm aiming for I have an electric smelter from vector but it doesn't have the capacity I'm looking for

@xlerb2286 Год назад

I would say if you're going to work with both aluminum and copper based alloys get two sets of equipment and keep things separate. It doesn't take much of one to contaminate the other. I've built a couple of furnaces before and you could do a lot better if you're willing to build a setup yourself. But for someone that's just getting into casting this doesn't look like a bad first setup and going with this could save you a lot of beginner mistakes in building your own equipment - you want to be safe after all. I'd suspect it won't be that durable though (but still good enough to get your feet wet) and if you do stay with it and decide to upgrade I'd plan on replacing most everything.

@1972Russianwolf 5 месяцев назад

ordered one from Devil Forge today. I have a smaller electric one already.

@philippeallard8852 9 месяцев назад

Hi, thank you for this very decent review. I just wonder where to find the ceramic wall sealing solution. Is there any commercial product readily available ? Thank you.

@thubprint 9 месяцев назад

A lot of people use refractory cement, the kind of mortar that is used to build brick fireplaces. I think you can buy colloidal silica on Amazon though, I was just fortunate when I googled businesses in my area that there was a furnace and forge supply house in my area. Advantages of living in a horse town I guess!

@curtisballer688 Год назад

Good review! Ceramic “ridgidizer “ what exactly is this spray you use to harden insulation? Something off the shelf from hardware store?

@thubprint Год назад

I picked it up from a blacksmith supply, it’s a colloidal silica suspension. Not terribly expensive and just an alternative to the heavy firebrick cement most folks use

@gianpaologazzola1234 2 дня назад

Hi, interesting video, I would like to know how long does it take to cast bronze? Thank you

@mickkelly4032 Год назад

What a Champion.

@JPCMETALHOG Год назад

With discount and coupon, Amazon price went from $249 to $145 with free shipping. Thnak you!!

@thubprint Год назад

Nice! I was impressed with the discount they offered, happy to be able to pass it along and help somebody out! That’s gotta be way cheaper than a diy kiln

@colerussell1780 Год назад

I got the 5kg size, I've used it about 10 times and had to customize the burner tip. The hinge weld broke off on it.

@ThePeterDislikeShow 9 месяцев назад

Do you have any suggestions with how to clean the inside of the furnace? It's gotten pretty disgusting and then one of my crucibles sprung a leak and molten zinc dripped inside. It makes me worry something might short out.

@bentleyalder5492 Год назад

Yaaaaasss 🥰 🥰 🥰

@f.demascio1857 Год назад

I'm wondering if my A12 crucibles will fit in there.

@leslieapplegate65 Год назад

The tongs should be junked. I've seen ones designed so that the part picking up the crucible are at a right angle to the handles and grasp the crucible around the body - much safer. Have fun with your new toy!!

@SSGTJonRogers 5 месяцев назад

I do not see one so can you link me to the ridigizer you recomend?

@jamesewa50 Год назад

I have some solid appears to be still rides from a car wash and their gold tenant on the outside. How do I test it to find out what kind of metal it is?

@GxxSxx Год назад

You are good man

@ironangel667 Год назад

How long did you cure it and how much did you use?

@peanut12388 Год назад

Have you ever heard of Devil’s Forge products? They have some good kits as well that could be reviewed.

@quincyharris2512 Год назад

Where do i get the red stuff you sprayed on the inside?

@RaveeCG Год назад

Hi! It is good for melting bronze? Can you suggest other ones? Thx!

@thubprint Год назад

I think it would be great for bronze because you wouldn’t have the problems zinc creates like with brass. There’s plenty on the market, but this company just added a stainless steel version that comes with the cement too, which might be worth looking at

@wannabescrapper72 Год назад

Awesome! I was balking at getting a Devil Forge because of the price but this is something I can afford. If the code you gave would work. The promotional code you entered is not recognized is the error I get.

@BE-kv5yx 5 месяцев назад

Just a quick question - how did you clean the crucible out between the different types of metal?

@thubprint 5 месяцев назад

I just used different crucibles, I haven’t experimented with mixing them but I’ve read that it’s best to use them for one material only

@BushDogScrapper Год назад

id say it looks like a pretty good starter kit! id love to get one one day! CheeRs Thub

@thubprint Год назад

Oh I’m real happy with it! I understand there’s fancier solutions but it’s cool when the cheap version works perfectly good

@BushDogScrapper Год назад

@@thubprint I’d be tickled completely pink with it 🤘🏻🔥♻️😎🤘🏻

@shadowcrusader2283 Год назад

where would you find Ridgedizer at?

@mucho73cobbcobb95 Год назад

Gotta heat them molds before pouring keeps all that crackling and popping to a minimum. Good work

@dioufmouna3539 8 месяцев назад

Bro is it possible to remplace propane by butane ?

@SJWCASTING Год назад

Downside of using cast iron molds with copper. I use graphite molds instead and the ingots look way better. You can wire brush the inside of the cast iron molds, but you will have a couple of holes in the end.. Preheat your crucible before using it, that way it will last longer. Now, is it worth it melting every piece of scrap and sell it.. Look at eBay, Etsy and see what some people will sell it for.. 1pound of copper for $35.. For me it’s a fun hobby, so it’s definitely worth it😁.

@KernsJW Месяц назад

Great video, but I have to go back to how you seem to treat teflon tape. Its not used as a sealant, but as a means to allow you to tighten the brass further.

@JunkNGrind Год назад

They are Beautiful All Sitting Next to Eachother Thub 🤩 I Desperately Want One ASAP Man 🤔👀🛠💪🏼🗑✅

@kelleyheard5790 Год назад

To melt down what you melted how much fuel did you use propane

@ohdannyboy4727 Год назад

pre heat your molds to prevent metal exploding while you pour. a piece of cardboard between your firebrick and crucible will prevent them sticking.

@joku8900 Год назад

Seems like I found fellow BigstackD viewer

@ohdannyboy4727 Год назад

@@joku8900 haha was wondering if someone would notice. I have it ingrained in my brain.

@thubprint Год назад

Cardboard between firebrick and crucible.. inside the kiln right? Neat! I’ll have to watch more of his content to pick up more useful tricks 😊

@ohdannyboy4727 Год назад

@@thubprint u got it!

@kevinroberson1985 Год назад

Does it come with crusival and tongs and did you say you got it on Amazon

@thubprint Год назад

It included one crucible and a set of tongs yes. It was sent to me but it is the kit they sell on Amazon

@keywellcoinsmafiametals8726 7 месяцев назад

I want one of these to melt both US and Canadian pennies to make some bars.

@Rantandreason Год назад

Alot of the comments seem to point to the fact that many scrap yards won't look at melted metals because they don't know the purity. Maybe you could do some videos on how to get your metals more pure?

@othername1000 Месяц назад

No link for rigidizer?

@johnhubbard6262 Год назад

Ahhh, fingertip hose clamp - A booze brewer-kegger dream.

@johnrebel9539 Год назад

When you use channel lock pliers to tighten brass regulatators instead of a proper sized wrench you end up rounding off the soft brass & then you will only be able to use pliers. I used to freak out on apprentices if they didn't use a wrench on regulators.

@TOTHEPOINT82 Год назад

7.8 on the maple scale is pretty rock solid science.

@jessicadavis7746 Год назад

cool!

@carnellbaker3970 6 месяцев назад

Want!!!

@DonaldPlugge 4 месяца назад

I'm currently cleaning out my shed. I'd like to melt down the old nuts, bolts, screws, and nails, rather than throwing them out. It looks like I need to get a furnace that can reach the 2800-degree Fahrenheit level. My preference is a propane unit unless you talk me into an electric unit. Down the road, I'd like to use the resultant metal to mold various projects. Would you suggest this expensive unit for such a purpose?

@thubprint 4 месяца назад

You want to melt down steel parts? I don’t really understand why but I imagine you’d rather use a horizontal forge so you can get pieces to temperature and remove them for some hammering and shaping and then put them back in. I’ve never heard of anyone getting steel and iron to a pourable liquid at home

@66bigbuds Месяц назад

They watch the videos and usually make upgrades according to the u tubers recamendations. They make numerous items.

@1pureone Год назад

Once you accumulate a decent amount of bars, I would like to see a video of your trip to the recycling center to cash in. I have wondered how they treat recyclables in this form.

@Dirt-Diggler Год назад

Badly IME Most yards will not be able to verify the purity of an ingot so will downgrade at best refuse at worst, in my experience in the UK, obv different countries and rules apply 👍

@billymacktexasdetective5827 8 месяцев назад

Why would anyone spend their time and money melting copper just to turn it in at the scrap yard??? I take bright bare, melt it into an ingot, and then try to sell it as bright bare to the yard?????? Talk about lack of IQ...

@nazahelbrum3318 Год назад

Like mild steel?

@MrIMacro Год назад

Thanks, can i use normal kitchen gas instead of propane?

@NWAHVAC 9 месяцев назад

By kitchen gas, I assume you mean natural gas. Yes it would be possible but you would need a new regulator (since this is how you adjust the temperature) and a new orifice. You could drill the existing one out if we know how many BTU the current one is and you know how to read the BTU charts.