VW Amarok Clutch and Flywheel replacement: Part 2, clutch, flywheel, oil seal and pilot bearing

Подписаться 2,4 тыс.

Просмотров 43 тыс.

50% 1

Part two of the 3 part series shows and explains the removal and fitting of the clutch, flywheel, pilot bearing and rear main oil seal.
Music Credits:
Song: MusicbyAden - Feel Good
Music provided by Vlog No Copyright Music.
Creative Commons - Attribution-ShareAlike 3.0 Unported
Video Link: • MusicbyAden - Feel Goo...
Song: MusicbyAden - Summer Love
Music provided by Vlog No Copyright Music.
Creative Commons - Attribution-ShareAlike 3.0 Unported
Video Link: • MusicbyAden - Summer L...
Song: Erik Lund - Summertime (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: • Video
Song: Thomas Gresen - Let Me Fall
Music provided by Vlog No Copyright Music.
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Video Link: • Thomas Gresen - Let Me...

Опубликовано:

1 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 32

@farrukovisionary7495 Год назад

Buenísimo Compa la Verdad que no te entendí ni una Palabra por el Inglés,Pero con las Imágenes me bastaron Saludos desde Tartagal Salta Argentina.🤙🇦🇷

@belisario3085 6 месяцев назад

hola, puedes indicarme cuantas libras pies de torque le diste a los tornillos de flywheell ?

@Mr18729 3 месяца назад

What size spline u using on the flywheel too take it off

@lorrainebwoy 5 месяцев назад

I have 1 to do tomorrow wish me luck

@marioalves7610 3 месяца назад

Just wondering why you have to put engine in top dead centre for the rear main I have my clutch to do I plan on replacing the rear Maine

@willemtreurnicht3818 2 месяца назад

It's simply a step to make sure that you have got the timing on the metal ring exactly right. If you use the timing tool for the rear main oil seal it will also require you to lock the engine in TDC. That is your default position for anything to be lined up that's got a position reference on the crank or camshaft.

@farrukovisionary7495 Год назад

Buenísimo Compa la Verdad que no te entendí ni una Palabra por el Inglés,Pero con las Imágenes me bastaron Saludos desde Tartagal Salta Argentina.🤙🇦🇷

@bencrosbie Год назад

Thankfully that can be done without a special tool save me 100 quid just to use it once lol

@boetaallen389 3 года назад

Hi Willem, hou hierdie videos van jou al vir 'n rukkie dop en het my baie gehelp. Moet nou moontlik self my flywheel en clutch vervang, bakkie maak n klop geluid as hy idle, maar geluid gaan weg as clutch ingetrap word. Watter gearbox olie het jy gebruik, ek sukkel om te kry en volkswagen kwoteer my R3000 net vir olie, dit kan seker nie reg wees nie? Groete

@maximilianovillanueva1756 2 года назад

Excellent video. Could you tell me where you got the tool to remove the crankshaft needle bearing? Thank you very much

@joecook3223 4 года назад

Dude i feel your pain with the spigot bearing, i ended up using a die grinder to get it out. Awesome video, thanks for your work

@davidspez7267 4 года назад

Thank you for such a detailed video.

@walatina12 2 года назад

Hi Willem , is there anyway of replacing the gear selector mechanism without removing the whole gearbox assembly?

@willemtreurnicht3818 2 года назад

Yes I believe you should be able to remove it maybe from the top into the cab. Have not done it yet... but quite certain it will be possible.

@thuanle296 4 года назад

Hello, I was wondering if you knew to to remove the prop shaft on my VW amarok 2015 model number 2H0521101c

@willemtreurnicht3818 4 года назад

front or rear one? The front one just levers off... There's a clip inside on the shaft that clips in place inside the cv. I used a crowbar to get it off... For the side on the trasfer case I just used a small piece of wood to lever against to protect the transfer case.

@rabahrabah3339 2 года назад

Good. Yas

@chibuikelebeanya4921 3 года назад

Hi, why do you have to set to TDC when doing a clutch

@willemtreurnicht3818 3 года назад

I replaced the rear main oil seal, so needed to time it to TDC to get the timing on the ring right that's part of the oil seal. The crank sensor pick up from that ring so it's quite critical that it's timed correctly. If you only do the clutch and not the seal then you don't neet to time it.

@zainfaruk5202 3 года назад

Can I remove the crank sensor in place with out removing cluctch

@willemtreurnicht3818 3 года назад

@@zainfaruk5202 Yes you absolutely can. It has a rubber plug and has to be removed from the front... might be a bit difficult to get there but it is designed to be removed with the gearbox in place...

@zainfaruk5202 3 года назад

If it is possible to show me a video can the corgi where the oil seal fits in the video you showed jump I am having a problem with my be amarok 2.0 TDI it won't start now power coming to injectors what can be the problem I will highly appreciate you help thank you

@willemtreurnicht3818 3 года назад

@@zainfaruk5202 did you refit the ring with the timing hole lining up? And did you time the engine on the crank for TDC? What part do you need to see?

@johanndupreez7736 3 года назад

Ek was bekommerd oor die crank seel, maar sien nou dit kan gedoen word sonder daardie "special tool". Baie dankie.

@willemtreurnicht3818 3 года назад

Johann mens moet dit wel meer versigtig doen as met die tool, maar ek het al twee so gedoen sonder enige moeilikheid. die een was op die 1.9tdi touran. Mens kan die tools redelik maklik bestel van aliexpress of een van die plekke af... En ek sou dalk, maar ek het die werk gedoen net voor ons in lockdown gegaan het en baie ander lande het al grense toegemaak... so was nie regtig op daardie stadium 'n opsie nie.