Wall OSB Sheathing and Tyvek House Wrap [Build a Workshop]

Подписаться 13 тыс.

Просмотров 35 тыс.

50% 1

Placing OSB on the exterior walls of your shop can greatly increase the strength of the building and helps to give a surface to attach the wall siding. I am using 1/2" OSB on my walls. Each stud behind the OSB is getting screws to make sure that the building is strong. After all the sheathing has been installed I install Tyvek Home Wrap. This is a material that repels water droplets while allowing vapor to escape. Tyvek tape is used on seams and gaps to adhere the sections of tyvek together. Nails are acceptable to install the OSB but I like to use screws.
SethCraft is a participant in the Amazon Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com

Опубликовано:

8 сен 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 51

@KB-ie7jr

Why not use 4x10 osb sheething installed vertically instead of 4x8 horizontally? You'd end up with less gaps in the sheething, less thermal bridging without all the extra blocking, and you wouldn't be left with that 2' section at the top. Only downside is that each sheet is 25% heavier and a solo install could be rough, but I assume that's what those 2 little helpers runnin around there were for, right?

@joeclark9042

Okay Seth I hate to say it brother but you did that wrong that second row you should have started at the other end and with the 6 ft so that way you split your joints all your joints don't run together they're not supposed to that weakens the wall

@tomamundson5119

Your vertical seams are supposed to be staggered down the wall. You should never have 4 corners meet at a singular point. Otherwise looks great!

@nikisrevenge

you should have started the sheathing on the bottom rim joist to tie in the floor system with the walls

@michaelschroeder6256

The border is required to have a nail not a screw every 4 to 6 inches depending on where you’re at in the us This is why they should be vertically not horizontally on walls you get your sheer strength from the nails and a nail every 8 inches in the field. And horizontally on roof decks On top of that you shouldn’t be using an impact driver to drive screws. It weakens the screw.

@steve123261 14 часов назад

This is not how to install osb or house wrap.

@h2s142

Sheathing starts at mudsill always

@curtisc808

Why didn't you stagger your OSB seem? Wouldn't that make it stronger? Just asking. Keep up the great work.

@tracysellman1562

OK, I have a question, Why would you not cover the sill plate with the side sheeting and nail it to the sill plate to lock everything in? I was always taught to do a minimum coverage of the sill plate if 2X6 then 5&3/4" and nail it in a zig-zag pattern. Sorry, my father was a general carpenter back in the 70's.

@michaeldvorak5556

You need a magnetic hammer for those cap nails.

@lonnieclemens8028

I admire your ability to work by yourself. Thank you for sharing this video.

@jllaine

Very Well Done, your best work ever.

@BrittCHelmsSr

Nice job with all of the sheathing and Tyvec.

@rafaeldominguez8213

Great job.

@mmbodnar

I just sheathed up a 16x10 and its was alot of work so I can appreciate how long this would take to do solo! Especially when taking the time to record, narrate and teach along the way. We just put on the common rafters for the

@audenjey7609

Great work!

@ttfweb1

Really good work

@fernandothompson2170

Awesome video

@user-cn2bu7tk9u

Good job thanks.

@joses8168

I just did my shed, did smooth side out and put pencil marks for studs which allows water shed if any gets below the tyvek. Also did upright so seams shoot down in case water gets in under metal siding and tyvek and does not siphon it in if horizontal OSB run on walls.. also a pneumatic nailer with 2 3/8 galvanized or similar is a lot faster sheathing. But did use the screw trick since I was working alone