Washing Machine Off Balance Repair, Samsung

Подписаться 3,4 тыс.

Просмотров 75 тыс.

50% 1

Revive Your Samsung Washing Machine! - How to Repair Suspension Rods. Is your Samsung washing machine acting up? Is it there a loud banging sound coming from your washer every time it goes into spin cycle? Does your Samsung washing machine refuse to go into a high speed spin leaving your clothes soaking wet? It is most likely due to failed suspension rod issues? In this comprehensive video, we will guide you step-by-step on how to repair Samsung washing machine suspension rods. You'll learn the essential techniques and tools needed to get your washing machine back to optimal performance. Don't let laundry day be a hassle any longer! Watch our expert tutorial now and say goodbye to washing machine troubles.
Link to after market Suspension Rods amzn.to/3HgFDtD
Link to Original OEM Samsung Suspension Rods: atlasappliance...
Link to magnetic trays amzn.to/3S2c040
The information provided in this video is for informational purposes only. The techniques demonstrated may not be suitable for all individuals or appliances. By watching this video, you agree that you are solely responsible for any repairs or modifications you choose to undertake.
Please exercise caution and ensure your own safety when attempting any repairs. Always follow the manufacturer's instructions and guidelines specific to your appliance. If you are uncertain or uncomfortable with the repair process, it is recommended to seek professional assistance.
I cannot be held responsible for any damages, injuries, or losses that may result from the use or misuse of the information provided in this video. Viewers should proceed at their own risk.
Furthermore, please note that some appliances may have specific repair restrictions or guidelines set by the manufacturer. It is important to familiarize yourself with those policies and comply with them.
By watching this video, you acknowledge and accept these terms and conditions."
#SamsungWashingMachine
#SuspensionRodRepair
#WashingMachineFix
#DIYApplianceRepair
#LaundryTips
#HomeMaintenance
#RepairTutorial
#ApplianceRestoration
#SaveMoney
#diyprojects
#ad

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 210

@gened9632 3 месяца назад

Thanks for the tips. Three things I'd add to this: 1. Perform a balance calibration when you're finished. Hold down "Temp" and "Delay End" buttons simultaneously for a few seconds and when it reads "cal", press start. It takes about 2 minutes to run through. 2. I pushed the right rear rod down the right side at an angle so I could weave the hose around it (from the top end) as I brought it up into position. Fighting it around the spring didn't leave enough room to do it without potentially damaging the hose. 3. Use a headlamp or a helper for the back right. If you drop your flashlight, you'll need monkey arms to reach it. I can't play basketball to save my life, but I can reach high shelves and to the bottom of washing machines (barely).

@appliancerepairamerican 3 месяца назад

Wow! Thank you so much for sharing . I will pin this comment

@mistyharper9722 3 месяца назад

We replaced ours and it still says off balance no matter what we wash. Today I wash a baseball uniform. Pants, shirt and pair socks and wouldn’t spin because it says unbalanced. What else could it be?

@gened9632 3 месяца назад

@@mistyharper9722 Mine is not 100% either. It's not as bad as before I changed the shocks, but it certainly has to be very well evenly dispersed before there's no issues. It's almost like loads too small cause more of an issue. The other thing that I found that was causing an issue was a code that came up 4C. It turned out that the drain hose was too far down the wall, not allowing enough air to vent and the machine reads it as a clog. These seem to be quite temperamental. I'm going to tear mine completely apart and figure it out. Unfortunately, it won't be for about 3 more months. I'm working out of town right now and I"m only home for a few waking hours on the weekend. My project will wrap up in Sept and I always get a couple of free months to recoup from the stressors of managing an out of town/night work construction project. So, sorry I can't get you a my findings sooner. Quality time with my wife is priority and I don't want to wake her on the weekends by me banging away with tools on a stupid washing machine. (It will involve copious amounts of tool throwing, bourbon, and profanity)

@appliancerepairamerican 3 месяца назад

@@gened9632 lol, please share when you can

@Jackofallmasterofnone94 Месяц назад

Just did the calibration and it’s like new. Thank you!

@thoth4 14 часов назад

Just Finished Replacing all 4 Suspension Rods (2024 Upgrade DC97-16350U) on my WA50R5200AW Samsung Washer. They look sturdier. No more Bounce when I push down on drum. We'll see how it washes. Thank You to the maker of this repair video. It was a life and time saver. Don't Forget to Recalibrate!

@appliancerepairamerican 14 часов назад

You are welcome

@IsaacCastellanos-l1n 2 дня назад

Bro is a life saver. I do recommend doing this just with two people though. One to hold the lid and only to raise the drum. Tons of grease. It sticks.

@appliancerepairamerican День назад

Thank you

@matthewburrell5623 3 месяца назад

Thanks for posting. 30 minutes and $45 in parts. Save me a fortune.

@appliancerepairamerican 3 месяца назад

Glad to help

@christophercosenza3343 3 месяца назад

I replaced them in less than 20 minutes and it fixed it. Kept my wife from scraping a $1200 unit. Thanks bud.

@appliancerepairamerican 3 месяца назад

@christophercosenza3343 You are very welcome. God bless you and your family

@markblakeman1306 Месяц назад

@@appliancerepairamerican I'm about ready to scrap my unit bc of how frustrating it is. Every load, it doesn't matter the size, the machine will go UB and refill over and over until it gets it just right. The unit is less than a year old, would this fix the issue? Thanks for the video and help.

@vanessapatman5591 24 дня назад

Thank you for this video!! I have one of these pain-in-the-butt washers and tried to do this watching half a dozen other videos. Yours was crucial for finally getting the top off. Lifesaver!

@appliancerepairamerican 24 дня назад

Your are welcome

@bambambig19 Месяц назад

Thank you for the video. I ordered upgraded suspension rods off amazon. This video helped me fix my washer today. Took about 30 minutes

@appliancerepairamerican Месяц назад

You are welcome

@jasonhess9307 6 месяцев назад

I appreciate the help. I was ready to throw my washer through samsungs corporate office windows and now I don’t have to go to jail.

@appliancerepairamerican 6 месяцев назад

lol, you still might want to when you see the price on the OEM Samsung suspension rods

@edgardolopez735 4 месяца назад

Jason i fill you🤣 thats how im filling right now

@tristanmurray3692 Месяц назад

We can go together

@carlosluislau4721 20 дней назад

@@appliancerepairamerican It's so ridiculous that an item that seems to need replacement every 3-4 years costs almost 50% of the cost of the washer itself (if replacing all 4 with OEM)

@TheBaitShop Месяц назад

This was a really fantastic video. Thank you so much for recording and posting it. I have it bookmarked and will check your channel for future repairs! Great job, thanks again!

@appliancerepairamerican 25 дней назад

Awesome, thank you!

@aureliomedina2678 5 месяцев назад

First time swapping these. The video is well done & concise, followed it step by step, and my washer is working great! Thanks for the video!

@appliancerepairamerican 5 месяцев назад

you are welcome

@brianloftin9196 Месяц назад

Thank you for this great video! I caught the “screwdrivers” as well and I love the fact that you were such a good sport about it when it was brought up instead of getting angry. On a tight budget, so I went with Amazon (Tomoon) rods that were highly rated with a lot of positive comments about how they are thicker and stouter than the factory rods. Just installed them, calibrated the machine and spun a huge load of wet towels with no problems. I didn’t cut my arms or hands, either! 🙌🏼 I did wear rubber gloves to take the old, nasty, sticky rods out and lubed the new rods with white lithium. Thanks again!

@appliancerepairamerican Месяц назад

You are welcome. Thank you for taking the time to comment

@jonathangutierrez1088 Месяц назад

Thank you for the step by step instructional video! I was able to repair my washing machine for $35.

@appliancerepairamerican Месяц назад

Glad I could help!

@pcjay9971 2 месяца назад

Thanks for the video, but I have a couple suggestions that should make it easier for beginners like myself. 1. Mention that the metal on the inside is EXTREMELY sharp. I cut myself on the forearm which required six stitches. 2. Take an existing rod out and measure it before you order. I have the exact same model that is used in your video. I used the link in the description to order the rods. I verified that the model number was listed in the description on the Amazon ordering page. The rods that came were just over 26", while the existing rods are 27". 3. Instead of trying to use one hand to disconnect the tension cables (this is where I cut my arm), remove the pack panel of the washing machine. This is done by removing the four screws on the back. This opens up the back of the machine allowing greater access to the suspension cables. 4. Be really careful while the lid is being propped up. If it slips, like it did on me one runs the risk of disconnecting some existing cables. This happened to me and cut the grounding wires (green, green/yellow wire) on the rear left side. 5. Like someone mentioned before, do a re-calibration before using. I'm bringing these issue up so others don't make the same mistakes that happened to me. I have replaced the rods and the washing machine works like new. Thanks again for the video.

@appliancerepairamerican 2 месяца назад

Thank you for sharing. We all benefit from eachother’s experiences. Would be great if you make a video.

@richmondlotelugukurradu8280 Месяц назад

Excellent video. This really helped me to fix my washer as many others did. Greatly appreciate the time and effort you took to show this to us. W as ame to do it in close to 30 minutes. 👏👏👏👏👏

@appliancerepairamerican Месяц назад

So glad that i could help

@babybee4923 Месяц назад

Amazing, ordered the spring off Amazon came within 2 days and only took me 5 minutes to install. My washing machine is working great now!! Thank you!

@appliancerepairamerican 25 дней назад

Glad it helped!

@renemedina5251 3 месяца назад

I’m gonna go for it. I’ll comment how it went for me after the fact. Thank you 🙏🏼

@appliancerepairamerican 3 месяца назад

Please do, beat of luck

@claireremlinger6490 5 месяцев назад

Thank you so much for posting this. I never thought I'd be able to fix my own washer, but your video was so helpful. You saved me hundreds!!

@appliancerepairamerican 5 месяцев назад

You are welcome

@emmanuelgarcia7790 2 месяца назад

Thanks for the tip !!! I fixed the problem. Happy wife, happy home 🏡 💖 💓 💕 💗 ❤️

@mridulmahajan3698 4 месяца назад

Thankyou so much for posting this video. All of the other videos I saw were total bs. But this was quite simple.

@appliancerepairamerican 4 месяца назад

you are welcome

@richs7362 10 дней назад

I've seen other videos of this repair where the rod ends were greased where they contact the washer, is this nessesary?

@enriquegonzalez6043 21 день назад

Thank you very much, i followed and your steps and it’s working fine now. 💪🏻

@appliancerepairamerican 21 день назад

You are welcome

@nicolashedian 4 месяца назад

Thank very much. This video was so useful. Simple change and not as intimidating as I thought it was going to be. Thank you so much.

@appliancerepairamerican 4 месяца назад

you are welcome

@Josiahrocco 4 месяца назад

This fixed our washer! Thank you so much!!

@appliancerepairamerican 4 месяца назад

You are welcome

@barbaravisoria6650 2 месяца назад

I replaced the rods, greased them, ran the calibration and this machine still needs to be put in a landfill. I'm so frustrated. I'm so angry that this machine barely lasted 4 years. Any other ideas? BTW the first 2 or 3 loads after the replacement worked great. Samsung is terrible for appliances.

@jonathanm505 Месяц назад

Might have to get samsung balancing rods instead of amazon, there probably cheap

@dyingforpie6879 Месяц назад

Same here- worked great for a month - the rods i bought were 70 bucks on Amazon- some say you need to buy genuine Samsung but isnt that what came with the washer to begin with? 😡 the washer start going unbalanced 11 months after purchasing

@justinw72ify Месяц назад

Me to as well I replaced the rids before no problem I just did it again still unbalanced!!!

@picollodiaries Месяц назад

google ‘drilling holes samsung washer’. dude posted a video of drilling 5-8 holes in the underside of the ‘balancing ring’. tried it and the washer runs full cycle. not sure about the long term…

@jonathanm505 Месяц назад

@@barbaravisoria6650 did you use dampening grease?

@danlboom2092 5 дней назад

Even with the new springs,you still need to Fortify and add extra drum (foam padding) on 4 sides

@danlboom2092 5 дней назад

Cont: this was overlooked by Samsung engineers__Bigger ,thicker Paddings on all four sides.This will minimize and reduce the rocking and shaking of the tub while spinning. Mine works just...now.

@appliancerepairamerican 4 дня назад

Thank you for sharing your experience

@gilbertguzman5391 4 дня назад

How do you clean that gooey stuff off your hands?

@kenboucher1765 Месяц назад

Thank you. This was a refresher course as I had to do this just over a year ago. Do you think this repair is going to be an issue every 15 months or so?

@appliancerepairamerican Месяц назад

depends if you used the Samsung rods or the knock offs and also how you use your washer. if you always max out your load size it puts more stress on the suspension

@kenboucher1765 Месяц назад

@@appliancerepairamerican Yep, 2nd time using the Prime ones. Although the originals only lasted 13-14 months. Instead of fixing the washer, Samsung just bought us out. Thank you again, Ken

@carlosluislau4721 20 дней назад

Is there a way to confirm/check that the rods are damaged/faulty? I would hate to change these if they aren't really damaged. Also, I didn't see on the video that you used any sort of lubricant (or white lithium) on the new rods? Is that necessary?

@maggiestoned1 26 дней назад

You are fast!!

@shawncooker9045 2 месяца назад

Thank you that was very helpful!

@appliancerepairamerican 2 месяца назад

you are welcome

@eduardolara8849 Месяц назад

Thanks for the video.

@appliancerepairamerican Месяц назад

you are welcome

@lanseaair 5 месяцев назад

Thank you 😊 so much for your detailed video, u made it look easy!! We should have wore gloves cause weird sticky greese got all hands from old part. I think we put too much effort in trying to raise drum but if you can get rod spring to give a little the top was the hardest for us. We did not have to release wires in back left seems our wires had length enough to raise top high enough. We have noticed our new Samsung washer just like the past one only last 4 years b4 having to replace the tension rods, disappointed in #samsung. We did run "calibration" which is found in the book. Definitely recommend doing that after installation. 1 load success yay! Thanks Amazon 4 for $45.00 & your video.....success.

@appliancerepairamerican 5 месяцев назад

Thank you for sharing your experience

@hayobatal9374 4 месяца назад

Se here, the greese is so bad I spent 20 minutes washing my hands. Though I am not sure if I clean the suspension rods and re-greese them if need to replace them.

@turbojoe62 4 месяца назад

What exactly goes wrong with the suspension rods? Springs get weak? Dampers go soft?

@gened9632 3 месяца назад

The springs just weaken. You'll start getting a ub (unbalanced) code on almost every wash. If you watch videos to diagnose, people will push down and it will bounce back like a 94 Civic with broken shocks. Mine wasn't nearly that noticeable. It just rocked to the sides like it was floating. It's just a rod with retaining cups on the top and springs with an inverse retaining cup on the bottom. The tub just floats on them.

@jkeys1984 24 дня назад

Will this fix a balance issue?

@stuemler Месяц назад

I want to know HOW TO REMOVE THE SPEAKER!!! Thank you.

@JakesSaltwaterTherapy 2 месяца назад

I see that cut on your right hand half way through. Reminder to always wear gloves or just be super cautious around sheet metal. Stuff is razor sharp

@appliancerepairamerican Месяц назад

Good tip!

@AnaS-f3r 21 день назад

Thank you

@appliancerepairamerican 21 день назад

You are welcome

@wellxplored 8 месяцев назад

Love the idea

@appliancerepairamerican 8 месяцев назад

thank you

@roywood9683 4 месяца назад

excellent video. thank you

@appliancerepairamerican 4 месяца назад

You are welcome

@jeffbarnes3118 11 дней назад

I’ve replaced the suspension rods twice a temporary fix after a few loads goes unbalanced, did a X Y axis recalibration works for a few loads, unplugging for 5 minutes and the XY RECAL works for a few loads then becomes unbalanced again. Any suggestions

@iandeleon8132 Месяц назад

At the beginning of the video, when you went to the back, you took 2 screws off before to snapped the top off. But at the end, when the top was back in place, I noticed you screwed on not only the 2 you took off, but 3 MORE after that at the back top of the control board. What were those for???

@appliancerepairamerican Месяц назад

most likely i pulled out screws that did not need to come out so i edited them out

@iandeleon8132 Месяц назад

@@appliancerepairamerican Well, turns out I needed to take those screws and that back panel out anyway, cause for whatever reason I couldn't take the control panel off without feeling like I was gonna break anything. Allowed me to get to the 2 screws in the inside. Anyway, switched out the rods, seems to have helped with the spin cycle. hopefully these rods last for a few years and not just a few weeks or months like few reviews have stated. Thanks!

@joshuagorz7872 5 месяцев назад

Thank you much for this info. I got the peices off Amazon for like 45 bucks, so i hope this works. I definitely dont wanna toss a 800 dollar washer

@appliancerepairamerican 5 месяцев назад

sometimes the after market suspension is not so great. There is also a link in the description for the Samsung OEM suspension. make sure that the washer is also level. the feet are adjustable . Have a fun repair journey

@mariacasillas2002 6 месяцев назад

I replaced these rods by flooding your instruction! My washer now spins properly. Thank you! The weird thing is that at the end of the spinning cycle the banging noise is still there. What else do you think I need to replace? I appreciate any feedback.

@appliancerepairamerican 6 месяцев назад

Check to make sure that the washer is level. Also it the Samsung OEM suspension is very expensive. sometimes when using the knock off suspension rods the problem still persists. There should be links to both options in the video description

@s0cal297 2 месяца назад

He forgot to mention to put some lithium grease on the bushings. You HAVE to put the grease on the top plastic part of each spring and inside that top bracket where the rod sits.

@Kris-st7cx 15 дней назад

Mine is still unbalanced. Any other advice?

@appliancerepairamerican 14 дней назад

Check to make sure the inner tub is not loose with in the outer tub. use Samsung OEM parts

@mlt61402 3 месяца назад

My husband did this and within 2 weeks it was getting unbalanced again, even with very small loads. What can we do to fix this?

@IvanRamirez-fs3sf Месяц назад

I replaced the suspension rods but the washer atill have the same problem i may buy the oe rods

@appliancerepairamerican 27 дней назад

check to make sure it is not something else. If you can wiggle the outer tube, moving it separate from the inner tub than you have a different issue. if so remove the agitator plate and make sure the nut is not loose. also sometimes the inner drum can degrade and separate from its center . also Make sure the machine is level

@dougcowdery9478 Месяц назад

I’ve changed mine twice with new parts only lasted a month

@Yakplanet_tv 2 месяца назад

I've already changed the rods. Still banging with little to no clothe in the washer. ?

@landonle254 Месяц назад

Same issue here. Does anyone know what else could be the issue or needs to be replaced?

@hoangphucngo5376 22 дня назад

Me too so frustrating dont know how to fix it.

@biggdoggdawn 2 месяца назад

I replaced the rods but it gave a UB again. Any thoughts

@pearldrops2278 7 месяцев назад

OK, I've replaced the suspension rods and it's better, but still throws the off-balance error code about half the time. What is plan B?

@appliancerepairamerican 7 месяцев назад

make sure that the washer is level. There are adjustable feet on the bottom that screw up and down to help level the machine. Sometimes if you don’t buy the expensive OEM Samsung suspension rods the cheep ones dont work as well. There should be a link to the OEM suspension rods in the video description

@vincentravo3926 4 месяца назад

Also make sure the rods match your washer. The ones in this video didn't match mine. I did find once just like it that had my washer model number on them.

@s0cal297 2 месяца назад

Calibrate the tub-you have to do this as part of the repair process If you still have issues, take the lid off again pull the rods and add lithium grease. There’s a reason the factory ones have that sticky grease on them.

@lyssathompson3182 5 месяцев назад

We have replaced the rods twice now. Thinking the first ones were the wrong ones. It still is very off balance....machine is level. What do i need to do? When it is empty, i can bounce the tub around like a basketball.

@FurnitureWarehouseBrampton 5 месяцев назад

We have same problem, replaced the rods but machine is still showing Ur code any help is appreciated

@lanseaair 5 месяцев назад

Call Samsung and ask how you can recalibrate your model. Their are buttons too push if you have a digital & after rebranded you should run calibration. Hope this helps. We are doing our rods on a 3yr old samsung.

@ianbundy9432 2 месяца назад

You just saved me a $200 service charge!

@appliancerepairamerican 2 месяца назад

You are welcome

@SamsungSmartWashingMachineFan 2 месяца назад

My dryer power cord and outlet is not in the middle, it’s on the right

@StayConsistant 2 месяца назад

Are the Amazon rods junk? I've done this twice using the ones from Amazon and both pretty much failed within a month. Or could it be something else?

@appliancerepairamerican 2 месяца назад

@@StayConsistant CAll +1 (800) 347-2745 for the Samsung original parts. have you model number ready when you call. If you order from Amazon make sure that the part number matches your machines model number and choose the part that has the most 5 star reviews

@bradtopper6860 Месяц назад

Just replaced the rods and still throwing a unbalanced load code during the spin cycle as before...I saw you mentioned it could be that the inner tub has separated from outer tub. Is there any way to fix this or just bring the washer to the curb and get a new one. Thanks.

@appliancerepairamerican 25 дней назад

There is a nut under the washplate sometimes the inner tub metal corrodes and you have to replace the inner tub. Usually cost prohibitive

@RussellD11 2 месяца назад

what if the rods dont fix the problem?

@Shabobidhuffy Месяц назад

Jam foam pool noodles around the drum to help restrict movement. Even new suspension rods don't fully solve unbalance issues as they are too fragile/soft even when new. Also this issue will keep happening over and over requiring constant replacement with this wear part $$$$$$$. no thanks, wedge pool noodles in there, then end.

@appliancerepairamerican 25 дней назад

Thank you for sharing

@dyingforpie6879 11 дней назад

Hello - i did this about 3 months ago the new rods lasted about a month anyone else? I bought them off Amazon 40 bucks the oem rods would cost me 270 plus shipping way too much- im now in the process of re- engineering a washer which in my opinion was a terrible design

@chadsrt 3 месяца назад

I have this machine and it’s 3 years old. Worked great with any size load up till this year. Started getting Ub codes so I replaced the spring rods and that didn’t work. Replaced them with off brand and those didn’t work. I am down to spinning two articles of clothing at a time. What else is there to replace for unbalanced loads?

@appliancerepairamerican 3 месяца назад

@@chadsrt The obvious is getting a level and making sure the machine is level. on that model you will need to take the top off to get a square edge to put a level on. the 4 feet are adjustable. The Samsung OEM suspension is very expensive, but it is recommended. Call this number and have you model number ready to get OEM parts: 800-347-2745. Other than that some Samsung have a Tub ring with fluid in it that is supposed to help balance the machine. That could have gotten a hole it or may have a problem with it. Best of luck

@Matt-v4t 2 месяца назад

I ordered these rods but now the tub sits too high and I can’t put the top back on. Any ideas on what the problem is? My washer is inoperable now. It’s the exact same model and ordered the same aftermarket rods.

@Matt-v4t 2 месяца назад

Found the issue, please remove the link to the rods you’re suggesting. They are causing a lot of people problems because they aren’t the correct length.

@robertbrincat5131 2 месяца назад

I replaced mine as well and still bangs... How ever, it maybe that I did not grease the new rods, so buying grease and tryng again...

@rilesw7576 Месяц назад

Ive changed the rods. No more unbalancing, but now we are hearing a clicking noise when its spinning. What is that?

@appliancerepairamerican Месяц назад

There maybe something stuck between the drums or under the agitator

@SouthTexasDeadeye 4 месяца назад

Very nice video! Just did the swap on mine and i thought everything went smoothly.However, now my washer just flashes at me when it comes to the spin and rinse stage. I noticed when removing the original shock rods the back right rod had a plastic bracket (believe you call it a pressure switch) attached to the rod and the cable was wrapped around the rod several times. Is the wrapping portion causing the issue?? I didnt wrap it to where its tight

@appliancerepairamerican 4 месяца назад

not unless it is being pinched. it is a hollow straw used to measure pressure as water fills the tub so it knows how much water is in it. if it is pinched or gets a hole or clog in it the machine will not know how much water is in it

@SouthTexasDeadeye 4 месяца назад

@@appliancerepairamerican you have any troubleshooting tips or ideas on what could be the issue??

@nerl453 5 месяцев назад

Thanks for the vid, the back right torsion has a hose it needs to go back in like it was, right? and it shows you putting a few screws back in on the upper side of the back panel ( 3:51 ) ... why? it didn't show you taking them out. Thankx

@appliancerepairamerican 4 месяца назад

I try my best, but when i make them on the job it is not as easy as in a film studio. Sometimes i miss a step

@ammasashwin1 Месяц назад

Hello thanks for the video. I was changing out my suspension rods on a very similar Samsung. The pressure hose in the back left hand corner was twisted around the rod. I was careful to twist it around the new rod. The top of the pressure hose is undone and I can’t see where to attach it to? I’m hoping it just sticks out the back and is no big deal? Thanks again

@appliancerepairamerican Месяц назад

It attaches to the pressure switch

@ammasashwin1 Месяц назад

@@appliancerepairamerican Thank you! The hose is damaged. I believe i can get a new tube and Jerry rig it. It's a latin American model and hard to get to the pressure switch . I'll get it and be better for it. Thanks again

@meenankgheewala8899 6 месяцев назад

How did you put the clip back from the top? Since it’s all the way on the right. Referring to the back right side. The part of the video you didn’t show

@YOGiiZA 6 месяцев назад

I moved the tube to left with my left hand and snapped the clip back onto the shaft of the suspension rod with my right hand. I hope this helped

@DS-nw8zc Месяц назад

Thanks for the video. I just repaired my wa50t5300ac/us. I did a test run on "spin only" and all is well. I used Amazon rods. My question is, did I suppose to coil the clear tube around the right side rear rod like it was originally, because I forgot and I did not.

@appliancerepairamerican Месяц назад

yes, it helps secure the hose to the pressure switch so it does not pull out during heavy movements. You should be ok, but if you start to have other problems check that to make sure the hose remained plugged in

@DS-nw8zc Месяц назад

Thank you, I appreciate your help.@@appliancerepairamerican

@juicemedina2445 3 месяца назад

Thanks for the vid helped me fix mine easy job instead of paying.

@appliancerepairamerican 3 месяца назад

Glad it helped

@royaldaba8437 4 месяца назад

What if it shakes even worse after new rods?

@appliancerepairamerican 4 месяца назад

Could be that the inner tub has separated from outer tub

@robertsharp6771 3 месяца назад

Double check you got the right rods. I'm an appliance repair tech, did rods first, then assumed shaft must be tilted slightly so did gear case, turns out either parts guy ordered wrong one, or wrong one was sent. Probably should have pink plastic caps for this model, green does not work lol

@s0cal297 2 месяца назад

Calibrate the tub

@tray2711 4 месяца назад

Samsung suspension rod WA45N3050AW/A4 can’t locate this part number

@appliancerepairamerican 4 месяца назад

Looks like a model number not a part number . The parts to the model in the video have a link in the description. I will look up the model number you provided soon and get back to you on a link for suspension rods

@raulrobles2961 5 месяцев назад

Can it be the rods are bad even if the washer spins fine when it's empty?

@appliancerepairamerican 5 месяцев назад

Yes, sometimes it will only bang when it has a load in it. Usually you can test if the suspension is bad by pressing down on the drum and when you release it will bounce. The problem with the Samsung is that the new suspension rods are expensive

@kylereece173 6 месяцев назад

I replaced the tension rods and it did nothing, still rattles heavily until it stops and starts over

@appliancerepairamerican 6 месяцев назад

Check to see what f you can wiggle the inner tub independently from the outer tub. Make sure the machine is level and use original samsung parts

@konradhof7318 5 месяцев назад

We replaced original suspension rods with aftermarket “upgrade” rods recommended in another video, from Amazon. Drum was banging around again in no time. And when I try to find OEM, they are no longer available, and/or cost same price for one rod as for 4 aftermarket. So very frustrating. I’m never buying this brand appliance again.

@luislopezjr.1592 4 месяца назад

Same with us. It’s absolutely garage!!

@vincentravo3926 4 месяца назад

Also make sure the rods match your washer. The ones in this video didn't match mine. I did find once just like it that had my washer model number on them.

@vincentravo3926 4 месяца назад

Also make sure the rods match your washer. The ones in this video didn't match mine. I did find once just like it that had my washer model number on them.

@appliancerepairamerican 4 месяца назад

Thanks for sharing

@konradhof7318 4 месяца назад

We decided to try again after the green “upgrades” bought through Amazon failed shortly after installation. We bought a different “brand” from a different Amazon seller, which had lots of positive reviews. Rods were thicker and spring had a 1” long rubber gasket around part of the spring. So far no problems (after about a week and a couple loads a day). 😎

@Parris-ju6yb 3 месяца назад

Hello, I changed out my suspension rods yesterday and I’m still receiving the UB error code and loud noise during the spin cycle. Everything is aligned as directed in the video. Any other advice?

@appliancerepairamerican 3 месяца назад

Some times the inner and outer tub become separated due to corrosion or a loose tub nut. In some samsung there is also a balance in the tub ring . These three problems can also cause the issue. The inner, metal tub should only spin inside the outer tub. It should not move independently in any other way

@catandherhorse1 4 месяца назад

We changed these and it's still shaking back and forth on the spin cycle and refilling with water.

@appliancerepairamerican 4 месяца назад

Check to make sure that the machine is level. there are feet in each corner that you can adjust to level it.

@angeljaimes3277 4 месяца назад

Thank you…thank you…. For sharing this video …. You just save me Aron $400.00 dollars on a service call and repair…… THANK YOU…..

@appliancerepairamerican 4 месяца назад

You are welcome

@daniejw 2 месяца назад

I’ve replaced mine multiple times and still out of balance. Ideas?

@appliancerepairamerican 2 месяца назад

Is the floor level? Did you use OEM Samsung parts? Is the inner tub loose from the outer tub? On some Samsung there is a tub ring that is filled with fluid. This can also cause balance issues

@MariaMedina-xg4pj 5 месяцев назад

Changed the rods but now the pause button doesn’t work what’s my problem?

@appliancerepairamerican 4 месяца назад

Samsung

@Jeffrey125s 3 месяца назад

There are many different suspension rods, please be sure to compare to washing machine model number, installation should be very similar

@appliancerepairamerican 3 месяца назад

true

@lSTEEF 3 месяца назад

Care should be taken pooping the console up. Mine popped up and ripped the plug out of the panel assembly. $300 later to replace it

@appliancerepairamerican 3 месяца назад

Thank you for sharing. this is channel where we can all commnet and help each other learn.

@Brainshatterer 3 месяца назад

I swapped mine and it went right back to bad. Bad rods? Need to rebalance? Thoughts? Prayers? lol

@appliancerepairamerican 3 месяца назад

possible bad rods. If you did not get the Samsung OEM rods. The aftermarket ones on amazon may not have done the trick. you also have to make sure you cross reference your specific model number with the correct part. There are other issues that could cause those symptoms too. The inner tub can be separated from the outer tub. The machine can be off level. Some Samsung have a tub ring on top that can screw up the balance too.

@Brainshatterer 3 месяца назад

@@appliancerepairamerican The whole tub assembly thrashes about with ease. I got the aftermarket thicker rod replacements. I just ordered the clamps I saw in comments and going to try that. Fingers crossed.

@jadkins69 6 месяцев назад

Mine has no phillip head screw drivers under the rubber pieces. :)

@appliancerepairamerican 5 месяцев назад

interesting , are there phillip’s head screws? , lol

@davidbarber8611 24 дня назад

The problem with these washers are the cheap seals that are in the suspension rods.. I finally got tired of replacing them every month, and make my own seals using my 3d printer.. been 3 months now and running like a champ

@appliancerepairamerican 22 дня назад

Awesome. would be great if you make a video and share . that is super cool

@Brianstraker 4 месяца назад

replaced the rods on my washer and it still has a lot of issues staying in balance. Samsung wa50r5200aw. is there anything else to help stability besides these rods?

@vincentravo3926 4 месяца назад

I just replaced mine tonight as well. I did one test load of towels and it seems to be okay so far. I did see another comment where someone said that in the manual it tells you how to run a calibration test?. Might be worth trying or looking into. 🤷

@appliancerepairamerican 4 месяца назад

The feet are adjustable to help level the machine. Check to make sure the inner tub is secured to the outer tub. If you place one hand on the outer tub and the other on the metal in er tub you should not be able to wiggle the inner tub inside the outer. It should only spin. There is a large nut that can come loose or the tubs sometimes erodes

@Brianstraker 4 месяца назад

@vincentravo3926 yeah I looked into that a bit last night. Gonna look more today.

@Brianstraker 4 месяца назад

@@appliancerepairamerican gonna find a lvl and check this out. Thanks

@bigDlindsey 3 месяца назад

@@appliancerepairamericanwhere is this large nut?

@JrVillatoro Месяц назад

Going to spin 1000

@YOGiiZA 8 месяцев назад

Screwdrivers ?

@appliancerepairamerican 8 месяцев назад

Screws, dah!

@jadedjay7861 Месяц назад

What a terrible failure design. Its like they purposely did it to sale parts.

@TheSpaceandsilence 3 месяца назад

The rods from Amazon are shorter, and paying over $300 for OEM rods doesn't seem like a wise choice. Not risking more money on a Samsung washer again!

@appliancerepairamerican 3 месяца назад

Wise