What Happens When You Apply a Rivet Nuts to Wood / Woodworking DIY 

Что выдумывать проще взять специальные ввёртки с резьбой снаружи и внутри, их садят на клей и они гораздо надёжнее

A modified version, with the rugged bending part moved a little bit more towards the end would be perfectly suitable for this application.

Thanks for doing this so we don't have to!

Since rivnuts are brand specific... try a plus nut or split nut designed to flare around an inch back from the face. From experience, the nut must be matched to the material thickness.

Try a prebulbed style? I often just epoxy rivnuts into wood after I've scratched a rough surface on the nut. It's good for making jigs, but if you want it to last, I always use the stainless steel EZ-Lok threaded inserts. Other threaded inserts tend to be too soft for most aspects. You can use the rivnuts in your video for things like aluminum or steel that is on a woods surface.

What's needed is a rivnut whose expansion zone isn't adjacent to the top of the fastener, but closer to the end so it expands with more wood above it to provide pullout resistance.

Trial n error new creation. Craft Level Up. Very nice. 👏🤙

A washer on the back for the thin ply?

Exelente video 😀👍gracias

여러 작업에 사용될 부품 같네요. 저도 언젠가 마음껏 사용해볼 날이 오기를 😊

Vc poderia fazer o furo para sair do outro lado e prender o parafuso pelo outro lado assim a resistência seria muito maior. pois exerceria a função de aperto muito melhor.

Rebite na madeira também seria a mesma coisa? E se colocasse uma arruela em cada lado, será que funciona?

Why this hemorrhoids? There are also special furniture threaded bushings

Как всегда здОрово 👍👍👍🥰🇷🇺

Sobre madera. Con un arandela de cada lados. Queda muy firme..

Needed different rivet

Почему не сделать так, что бы внутренняя втулка сплющивалась в середине, а не скраю, намного прочнее был бы узел

Onde comprar???

lustig aber braucht kein mensch. umständlich und gibt bereits günstige produkte die besser sind

You can make the bulge on the nut happen further down into the wood by wrapping wire around the shaft near the top of the nut. That way when the screw compresses the nut, it can't do it right at the top -- the wrapped wire prevents that compression there.

Nitonakrętka była stworzona do łączenia cienkich blach za pomocą połączeń śrubowych lecz bez dostępu z jednej strony i niemożności wykonania gwintu w zbyt cienkiej blasze o wystarczającej sile na rozciąganie takiego połączenia. Można nitonakrętkę stosować do innych materiałów ale trzeba liczyć się właśnie z mniejszą trwałością związaną z mniejszą wytrzymałością danego materiału niż metale. Ja używałem nitonakrętek w tworzywach sztucznych. By nie uszkadzać tworzywa i wzmacniać mocowanie dodatkowo dodawałem metalową podkładkę, co nie zawsze jest możliwe.

Try the longer ones meant for thicker plates. Crimple zone is further down the pop nut

Ist doch selbstverständlich, daß die Niete nicht halten kann, wenn das ins Holz gebohrte Loch kürzer ist als die Schraube, die man anschließend in die Niete schrauben will!

I'm pretty sure if you drilled those holes deeper than you did it would not try pushing out while you were installing the part. If you watch it's pushing out because the bolts are bottoming out on the back side pushing the whole thing out before it can start to expand.

Put the rivnut in from the back (if possible) and the flange will pull against it instead of pulling out the weaker expanded part.

Very nice, you could drill through the wood and use it as a blind nut. Really strong. I will have to include this in my list of Fasteners. Thank you

При тесте на отрыв. Нужно учесть что болт упирается в древесину и вытаскивает основание. А нужно было тогда просверлить глубже отверстия под болт.

Здравствуйте, спасибо вам . Что в роликах идёт показ как и что и для чего , многое почерпнул для себя , кое-что не ново ,но пойдёт. У вас подача хорошая ,так держать 🤞🤞🤞 . С уважением с берега озера Балхаш

На мой взгляд на видео очень доступно продемонстрировано, что всё таки резьбовая заклёпка не очень удачный вариант для дерева. Гораздо лучше на эту роль подходят втулки с метрической резьбой внутри и крупной резьбой для дерева снаружи.

These rivnuts are very common used in the aviation industry. Thanks for sharing 👍

I had a real specific need a while back, and it did not need to be real strong and I ended up using some of these in a concrete wall. I drilled a hole just slightly larger than the rivet nut, coated the outside with an epoxy, inserted and compressed. Held like a champ.

I’m surprised it works although I wouldn’t trust it, they make wood treaded inserts for machine screws. I did like the video!😊

Что за бред. Для дерева саморезы есть.

Прям капитан-очевидность...

По металлу да... А по дереву Нет!!! Нет!!!Нет!!! Дерево материал живой.дышит.меняет плотность и форму!!! Так что это неудачный пример всё рассыпется!!

Excelente tutorial maestro, cómo siempre unas ideas peculiares, gracias por compartir sus conocimientos y experiencias, un saludo cordial y por supuesto un gran like desde Narón (Galicia)👌🤓

Gracias por su trabajo, tiempo y dedicación. Muy útil y práctica la tuerca.

Put a few drops of oil on the thrust washer and bolt threads, it will go easier and last a lot longer

Increíble, acabé en la cama con mi señora 😂🤣😂🤣😂🤣😂🤣💃🦸‍♂️🦸‍♂️💃💃🦸‍♂️🦸‍♂️👍🏻

Excelente ideia . Brasil -> #ForaBolsoNazis

This is wood expansion anchors. The same as in concrete - KB-TZ2 and many other manufactured by HILTI and Simpson.

I use this nuts with super glue, little bit less hole put glue and press nut with hummer.

Now that is cool 😎 Thanks for sharing 👍

those are not rivets ,,, they are rivinuts ,,, totally different thing.

Зачем такие гайки в древесине для этого мебельные забивные давно изобрели

There are threaded screw inserts which are specifically designed for soft wood 😅 Might want to look into that if you work with this a lot. I have seen a type which is self-tapping as well, so you don't need to pre-drill holes first. Good stuff👌

Под дерево нужны другие заклепочные гайки - чтоб насечки предназначенные для деформации были расположены как можно дальше от прессшайбы, может даже в два ряда - если Вы хотите использовать эту технологию для дерева.

목공에 관심있는 일인입니다 너트 만드는 회사에 건의를 하면 안될까요? 주름 부분을 머리에 바짝 붙여서 하지말고 목공용으로 중간쯤에 주름을 만들어 달라고. 그러면 완전 목공용으로 쓸 수 있을 듯합니다~~♡♡

They would be great in hand wood. Manufacturer needs to make some for wood alone. Wrinkle deeper

Ce n'est quand même pas fait pour cela.

Like19,.,.,. 영상 잘 봤습니다!! 또 오겠습니다!!

You should try it with rivet nuts intended for thicker materials. It moves the “weakened” part farther from the surface. I bet it would work even better. This has me thinking how pop rivets would work!🤔

Try torquing them down to expand but not all the way they rip the wood away to nothing

Guarda che esistono già le bussole in zamak o ottone da applicare nel legno con la filettatura interna metrica.

А есть же специальные для дерева с шариком внутри

Показывать надо на липе, ели и ольхе, а на дубе и так понятно.

👍👍👍Лайк в карму за креатив и полезную информацию!

So what you're saying is if you must use in wood first drill plenty of relief behind it second don't tighten it all the way down and third never use for anything structural... got it thanks, very informative

Es la primer vez q lo veo, lamentablemente acá en Bogotá, Colombia no lo importan. Así como otros tipos de tuercas las armado entre paneles, módulos, bases etc.

Great idea, but not sure if it’s better than using threaded inserts. Any thoughts, anyone?

Amazing work ❣️ I am support your Chanel ❤️ Have a great day 😊

Slt c est une excellente découverte j avais pas pensé à cette méthode, car il existe des chevilles pour le bois mais !!! Et sa a l'air de bien fonctionner p 👍👍👍👍

Buenos días. Buen video. Sería posible saber donde adquirió el útil para las tuercas ?. Muchas gracias

Rivnuts plus a dab of epoxy would be very solid.

Эти заклёпки для метала а не по дереву по дереву есть специальные заклёпки

목재나 프라스틱용 너트리벳이 따로있음

Little apoxy will be strong enough, but they make similar things for wood

이번 영상도 기대를 저버리지 않는군요 잘보고갑니다 역시 👍 다음 영상도 기대해볼께요

If you use these a lot I would recommend lubricating the compression bolt. It will make it last much longer.

Ф,футорки в наличие валом

감사합니다. 당신같은 실험맨 덕분에 신문물을 접할 수 있습니다.

شرح عملى مبسط ورائع 💪👍

Where possible the nutsert can be installed behind , with a thro hole in the wood to fasten from the opposite end. Will be more robust.

Nice video. Thank you!

안녕하세요. 검은별님 이런 방식으로 목재에 쓰는 너트 중 혹시 목재피스에 맞는 직경의 너트는 뭐라고 부르나요? 꼭 알고 싶습니다..

What about just under sizing the hole and threading directly into the hard wood?

I absolutely love riv-nuts. It's niche thing but once you have a tool and bag of them, you find uses.

목공용으로는 애매하다는 생각이 드는군요. 한번 세게 쪼이면 터저버리니.. 참고되는 좋은 영상입니다

Ese recurso no es para usarse en la madera. Para la madera hay otros que funcionan perfectamente

질문입니다. 제가 아는 나무공방서 레드파인이 단단하다며 그거 쓰던데요. 소프트우드에 속합니까? 인터넷서는 멀바우가 무르다 적혀 있기에 가구 고를때 멀바우 제외하고 레드파인 검색합니다. 오디오 장식장도 멀바우는 쳐다보지도 않았어요.

실망시키는법이 없는 영상~~~🍀🍀🍀🍀🍀

목재용으로 쓰면 안되는거라 안쓰겠지만 궁금하긴 했습니다. 실험 감사합니다.

우그러지는 부분이 중간쯤에 있는 제품이 있으면 목제용으로 좋을 것 같단 생각이...

Para resolver el problema en la madera, tan sencillo como poner una arandela para que la presión la absorba ésta y no se hunda. Así lo hago y me funcilna a la perfección.

1 giả lập tuyệt vời 👍👍

A really useful test. Thank you. Not something I would have thought of doing, but, yes it works, with appropriate guidelines.

Для дерева есть другие

Заклепочные гайки для металла а не для дерева

Эта заклёпка предназначена только для тонкого металла,Ане по дереву

For hardwoods you can use a tap & die. No ongoing cost of RivNuts

Слабое место нужно к центру переместить

나무의 종류별로 테스트에 굿~입니다. ^^ 니벳너트~용도가 다양하군요

What is Rubber wood?

Just use threaded inserts.

음 잘 뽑히지 않는거 같아서 신중히 사용해야 겠네요!!

Hay quá! Cám ơn đã chia sẻ

8mm로 테스트 하신거죠?

Good test. I'll stick to threaded inserts

👍👍👍👍

you should try a plus nut for deeper holes