When Things Get Complicated -Iphone Water Damage 

wow, 3 videos in 1 day. This is like Christmas present. Thank you.

Uplugging battery to check current draw left me amazed, 300 IQ and loads of experience, you are amazing sir...

Wow! You have become so good i can't follow anymore. Thank's anyway for the knowledge! I am 61 and i shake to much to change a micro component like this and the way you diagnose the problem. I wish so much to work with you evey day. Thank's again Sorin!

Wow..three vidios in one day...thank you MR, Sorin.

Nothing wrong with that repair. Most couldn't micro solder something that small but are fast to criticize. Keep up the amazing repairs and keep teaching. Really great stuff.

I like watching you fix Apple products, not a fan of Apple but it's good to learn how to fix them.

Big Boss of Electronics repair !

Hey Sorin, I was walking along a Thai beach. A Thai lady asked me if I want short time fun. I said ok and paid £30. She then pulled out a tazer and shorted me to the ground. What a shock! Thanks for video.

Sorin is NOT a fake friend. : )

Sir, you're too much. I can't wait to work confidently like you, especially PCB fault diagnosis and other problems in mobile phone repairs. You're a good engineer.

Hi there, I really like your channel, I have learned a lot from you. Thank you so much for this channel you are an expert in electronics and I appreciate your sharing your knowledge with us. Greetings from Bosnia and Herzegovina

Greetings from Syria again, you are talented , I wish I could do that , you are doing as a doctor in surgery ... Thank you for teaching and recording

thanks Sorin

thank you repair school

As Usual a Very Good Video...Sorin you are good!

Love these videos, always nice to see an iPhone come back to life 👍

I really like you solin and except you who is not fake beacause you dont love yourself and share your knowledge to everyone! Much thanks!

some people use longer wire so does not get hot too quickly from the other end.. or some use uv mask

thank you

it's amasing what you do! I don't think there're many capable to do what you do.

Great video, Sorin! Good to see you got it working!!

you really need a pair of fine cutters and solder wire first to capacitor because it is larger.

such steady hands sorin

Great Job

Nice repair Sorin. Please make your own flux No tooth 🦷 this time 😁 And time to make your own T-shirt merchandise with flower shorts I will buy it when it says dentist repair and hot glue specialist 😂😂thank you again for the great videos

400mah should be somewhere 3.0v, usually the caps around nand.

amazing video

Hi Sorin, I was wondering maby you can talk more what tempereture you use with hot air stasion and air flow. becaus it is easy to burn if you dont realy know how to use station.

How did Diana swap the screen? Thanks.

Ee I bought a new bottom case of a laptop because I didn't have any hot glue. Nice videos in my area we don't have I phones but I think this knowledge is universal to other phones and laptops. Thanks

Very good job. You had good fun

Would you beable to do a video fixing that screen or other screens, thanks

Hi! Great video! What do you use to replace the black sheet of shielding of motherboard? Because is an EMI shield. Do you use just KAPTON? HELP

I love this

You are the best

Hello there, I love your channel. Thank you that you share you knowledge with us. MULTUMESC from Cyprus.

Hi Sorin, the petrol that uses, is the same that car uses or is other product? Thanks.

yes this one is hard but lesson alot with it.....

One thing I don't understand. Why are you making that bridge to the capacitor? Is there broken truck?

Wasn't a pin on the display connector burned? 3rd on top right. It's marked in blue on phoneboard, not gray like ground. What does blue mean?

Hi, Sorin. I Always wait for your your rapair school videos. You don't need any thermal IR rubish tools. You use MacGyver magic tools like petrol and alchohol.

Hi Sorin, At the minute 35:19 (circa) you are starting to remove what you call "glue" (that black goo all around components). The question is: - how you will remove it? - Can't you solder the new chip directly on top of that? - I've seen you use the solder tip like a scrub.. is it normal soldering temp or it is lower, not to damage the tracks? - that glue cannot be removed using some chemical? Please, be so kind, let me know. ciao Mario

Is your hot air gun really that quiet? Can't hear anything when you perform.

Thanks 👍👍👍

Hello Sonir very good video I have a question what do you think about cleaning phone board in Ultrasonic cleaners.

I got a question Zippo lighter fluid. Or 99% alcohol to find overheating. can you really use Zippo lighter fluid to clean that board.sorry it's just something I've never seen too many tech do but let me tell you you are one smart genius.

How much had to pay the customer for this job?

My friend iPhone 6 has a totally drained battery. I measure a bit over 500k ohms on the board battery connector from positive to ground. Does this sound like a short somewhere in the board that pulled the battery to 0 volts? Is there a way to give the battery some charge without a power supply? Thanks you Sorin

Thank you......🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹

Wow 3 videos, and great job as always👍👍

Thanks Sorin , You make it look so easy.I would have blown all the other chips off the board. hehe :-)

Awesome

Laptops and desktops plz hehe

finally came the phone video :)

maybe someday will be time to clean that toothbrush and to buy side cut pliers :)

Good and nice job!

Wow more Videos...Cool

😂 Fake flux you make me laugh sorin

Hi Sorin , please if is not to much r u Ro ? .....Dacă da te rog a-și dori sa iau legătura cu tine pt a-mi repara un telefon care a căzut in apă . Mulțumesc mult. Any why u r 👍🏻🙏🏻👌🏻

all tweezers suddenly disappeared from your desk ? C'mon Sorin.. you have camera behind there, you can track who took these tweezers..

Guys, i can't tell you enough how important what I'm about to say it. Seriously. WATER itself, is NOT a threat to your system. If you open it up, and see water or liquid in places... GREAT!!! NO DAMAGE. So what you want to do, instead of hair drying, is wiping it up with those ear bud sticks, wipe the water away. Why? because it's not the WET part of the water that breaks your electronics, it's the Mineral content of the water when it DRYS. Very important. When it drys, it deposites green materials like iron etc, which erodes things. So get it while it's WET and clean it with cotton, DONT dry it. because you're still drying it into the board. Where is the mineral content? on the board. CLEAN it first.

Hi Surin. Thank you so much for your channel, it helps me a lot. I have a question. I have two iPhone 6 boards. No power, no charging, not short. I connect a multimeter and there is no short. I connect a power supplier and there is no short. What can I do to detect a disconnect on the board? Thanks. Sharon.

Turkey Hello Superman

Sorin, you wait for so long time to have the phone finally up&running... meanwhile there was *NO SIGN* on the display that it was taking time to get up... HOW do you know it was getting up? and need to wait a LONG TIME to have it finally on? Yes, you can say: "...it's my experience.." but how you faced it the very first time it happened to you??? I know you usually don't give answers here... but I'm STRUGGLING in this dilemma... It happened so many times to me to have a blank screen phopne, right after finding a broken chip, but NEVER imagined it *could* turn on after so much time!!! Please answer me, if it is possible to you. thanks!

İf it is practical to use, why change them ,not every people wanting to try new things everyday!.

ok sr

👍👍👍

short the fuse, short the fuse....................

+1

Convince your boss to buy a Flir One Pro. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE--GCazDq76os.html

first !