Thank you for Demonstrating the Diagnostic Modes. My washer would start and wash for alittle bit then I would get Flashing lights and the F was displayed. After doing your test The code was F51. I appreciate you making this video it made me feel relieved, so I'm able to tell the repair person. Thanks again.
Have the exact washer as in your video and the matching dryer. Bought them in early '21 for $100 each and they were like new. Haven't had a single issue with either unit. I had no idea about this diagnostic test. Very well done video. Thank you kindly for taking the time to make it. I saw it was done 6 years ago and I would have never guessed the washer and dryer I purchased for $200 were that old. They're like new!! Not a scratch on either unit and both work fantastic. I guess I got lucky. Thanks again Mr. Wayne!!
AWESOME VIDEO !!!!!! I NEVER KNEW THIS. I did have a repairman come 4 years ago and he said my rods were bad and he replaced them. It seems when I put alot of cloths in it will never complete . So i have learned to only10 to 13 items and it works I also never put my spin cycle on high, Cause when i do it always Seems to stop and I have to reset all over again. My washer did all the cycles you said. THANK YOU THANK YOU BIG TIME
Thanks for making this video, my machine was stuck somehow but, with no error codes.....running the diagnostic seems to have unstuck it and now its back to normal. :-)
Thank you. I have a different style but same brand (Whirlpool Duet Front Loader: Mod: WFW9151YWCO) With the power off of the machine, still plugged in, I hit, Delay Start, Extra Rince, and Cycle Signal. One right after the other starting with Delay Start. Did this three times and the error code appeared, LF. I than pressed and released Cycle Signal and the code moved to E1, F6 repeatedly. Still cycles through and doesn't stop. Thanks again.
hello !! so i made it through the entire video and my washer has done every step so far except for hit "done" . its still on c8 and wont stop .. how do I fix that ?
This is a helpful video. While doing the diagnose on my washer on c8 it will not actually spin, it only moves like in c7. Any advice on what it could be?
@@dariuscoleman2046 Thank you for your response. Now my washer won't do a damn thing it just keeps beeping at me. So I have a new issue to worry about. 😅 Got any suggestions for that?
No error codes and runs through test mode with no issues... But, still won't go through a cycle without stopping, draining, and coming up with oL on the display, even when empty. What could cause that?
@@berrypatch5583 The only thing that worked for me was running the Clean Washer cycle. After that, I ran an empty Quick Wash cycle and it worked. I'm sorry, I didn't get alerted to any replies to this comment until just today.
@@infocuscareers The only thing that worked for me was running the Clean Washer cycle. After that, I ran an empty Quick Wash cycle and it worked. I'm sorry, I didn't get alerted to any replies to this comment until just today.
Any idea what can be wrong with my Whirlpool Cabrio dryer - the buttons all work but when I press Start it hums and stays in sensing mode without tumbling but it does heat up - what can be the problem? I can turn the drum manually and it doesn't feel like anything is hindering its ability to turn.
Urgently need your kind assistance. I have a Whirlpool Cabrio. It shows "sd" error code. I would stop at the last spin. I have tried several times to use the bleach and clean cycles. Not removing the code. Can you please help. Is there a reset button or calibration function to see if this will go away? How can I fix myself. I called around and everyone is extremely costly during the holidays! Please help. Thank you in advance for your kindness. Happy Thanksgiving!
Terrific video. Thank you for taking time to make and to post. I have some questions about what I am experiencing with my washer. May I co tact you directly?
Hi I just got a used whirlpool cabrio and I'm having the same problem as the people that commented before me. My clothes end up wet after the cycle is over. The water is drained but apparently the spin cycle is not completed. but if I set it to "spin and drain" it does work. Do you know what the problem is? and how I can fix it? I would appreciate your help.
For Samsung: during test it goes through them by one or two digits: 1. lid lock. Ho (hot water) Co (cold water) 6. Agitation. 7. Drain. 8. High spin test. 10. End
So my husband bought this washer at a yard sale. So I tried it and when it's time to since again or spin it won't work 😒 so I turn it off then on and push start. But it usually turns off like 2 or 3xs so I just stand their till it actually starts working. Then to finish the last cycle I turn off and change it to drain and spin. I really don't like this. Someone help.
I have the same problem, both with my husband just randomly picking up a washer, to the error and having to reset it after each cycle. Have you found out anything about this? Google and RU-vid seem to be no help.
When it happens to me I too restart it, powering off and on, But I also change the cycle from colors, or heavy duty whatever i change from whatever I had it on before, Till it goes and does what it was supposed to do the first time.
Duet Sport HT Lavadora Diagnóstico, tendras otro video, mi lavadora en los ciclos de lavados no funciona, se le cambio la manguera de la tina a la bomba q estaba dañada, como le hago el diagnostico para saber si es el CPU u otra fall
I have a Whirlpool Cabiro Platinum series washer. When I run diagnostic code, after C1 diagnostic it does not continue and blink time and start/ pause button. Any help will be appreciated
during the diagnostic check mine would not go past C7 either. The pump continues to run as if it is trying t empty the water yet the washer is empty. another thread I read said that the main computer board needs to be replaced. I hoped that I would find a simpilier fix. replacing the main board sounds expensive.
Here is all the error code: BUTTON Cabrio Washer Fault Codes Fault Code Washer Problem Repair Steps LF (F30) Long Fill LF flashes when the water level does not change for a period of time after the valves are turned on OR water has left the drum but control does not detect a water level change. Is the water supply connected and turned on? Are hose screens plugged? Is water entering the tub? If so, check the pressure hose connection to the machine/motor control. Ld (F32) Long Drain Ld flashes when the water level does not change after the drain pump is on. Is the drain hose or the drain pump clogged? Is the drain hose height greater than 96 inches? uL (none) Unbalanced load uL is displayed when the machine/motor control detects an off-balance load and remains on while the washer runs a mini-cycle to rebalance the load. Display clears if mini-cycle successfully rebalanced the load. If the mini-cycle is unsuccessful, uL will flash until the door lid is opened, allowing the customer to view and redistribute the load. oL (F70) Overloaded oL flashes when the machine/motor control detects a load size that exceeds the washer’s capacity. Open the door lid to clear display, remove excess laundry, then restart the cycle. Sd (F71) Suds Detection Sd is displayed when the machine/motor control analyzes drag on the basket and detects a suds-lock condition. It will remain on while the control runs a mini-clean out cycle. If the clean out cycle is unable to correct the excess suds problem, the cycle ends and Sd flashes in the display. This may signify: Excessive detergent usage. The basket cannot engage during drain step. Mechanical friction on drive mechanism, not allowing the basket to engage. Lid (F81) Open/Close Door Lid Lid flashes when the following conditions occur: User presses START with the lid open. User presses START after two consecutive machine cycles without opening lid. The machine/motor control cannot detect the lid switch opening and closing properly. Po (none) Pump Out (lid opened) Po flashes when the drain pump begins pumping out water from tub because the door lid is left open for more than 10 minutes. Close door lid to stop the drain pump. HC (none) Hot, Cold Reversed HC flashes when the hot and cold inlet hoses are reversed. Make sure inlet hoses are connected correctly. dL (F80, 82, 84, 85) Door Lock Failure dL flashes if the following conditions occur: Door lid is not closed completely due to interference. Lint and detergent residue is preventing the lock bolt from extending. Machine/motor control detects an open door lid switch when attempting to lock. Machine/motor control cannot determine if door lid is in a locked state. DU (F83) Door Unlock Failure dU flashes if the following conditions occur: Excessive force on the door lid is preventing lock bolt from retracting. Wash residue is preventing lock bolt from retracting and should be cleaned away. Machine/motor control cannot determine if the door lid is in an unlocked state. F1 (F60-68) Primary Control Failure F then 1 flashes when there is a primary control failure. Replace the machine control assembly. F2 (F2) Keypad/User Interface Failure F then 2 flashes when in: Diagnostics Test mode if a stuck key is detected. Standby mode if there is a user interface mismatch. F40 (F40) ATC Thermistor Open/Short F then 40 flashes when the ATC Thermistor is detected to be open or shorted. F41 (F41) Motor RPS Thermistor Open/Short F then 41 flashes when the motor rotor position sensor (RPS) thermistor is detected to be open or shorted out. F42 (F42) Heater Thermistor Open/Short (Not Used) F then 42 flashes when the heater thermistor is open or shorted. F50 (F50) Motor Stalled F then 50 flashes when the motor rotor position sensor (RPS) senses no rotation. Does basket turn freely? If not, make sure bottom shipping pack has been removed. Determine the cause of friction. F51 (F51) Motor RPS Failure F then 51 flashes when there is a motor rotor position sensor (RPS) failure. F52 (F52) Motor Stop Failure F then 52 flashes when the motor rotor position sensor (RPS) senses rotation after stop command. F53 (F53) Motor Control Overtemp F then 53 flashes when the machine/motor control detects high temperature for the motor module. Does basket turn freely? If not, determine the cause of friction. F54 (F54) Motor Control Overcurrent F then 54 flashes when the machine/motor control detects high current for the motor module. F72 (F72) Basket Re-engagement Failure F then 72 flashes when the basket check routine fails to determine if the basket is re-engaged after being disengaged. Is the basket floating? If yes, pump out water. See Long Drain. Does basket turn freely? If not, determine the cause of friction.
Lokesh Puri yeah my washer is fixed now we had to get a service tech out here not once but twice was something with the the bucket sensor I was stuck or something like that so it's more internal if yours is doing the same thing it's nothing a button or diagnostic test can fix you have to get a service guy out there to help take care of it and luckily was under warranty so didn't cost us nothing but if we had to pay out of pocket it was going to be at least the $800 bill
Joey P. Thanks for your reply. I appreciate your response. Mine is 5 years old, I would check with a technical and buy a new one if it requires more than $200- $300 to fix. Once again thanks for your reply
Really? So all the recalls on their new lines of washers is what? cause they miss looking at them and want them back? Samsung's are damn fine looking, but performance is no better than any other make of appliances. What should really burn your ass is looking under any of these new washers. the outside looks pretty damn fancy and expensive until you look under the proverbial hood. Then you see exactly how cheap the parts are that go into them. I swear these people spend $25 bucks per unit to build them.