Windshield Installation - 1967-68 Cougar / Mustang

Подписаться 25 тыс.

Просмотров 35 тыс.

50% 1

We certainly aren't the first ones to make a windshield installation video, but it never hurts to get multiple opinions before you give it a shot. In this case, we're installing a new Pilkington windshield into a 1968 Cougar, but the process is exactly the same on a '67 or '68 Mustang. Perhaps the most useful tip we have compared to others is to use weed whacker string for pulling the seal into the car. You'll see.
Also shown is the installation of the stainless steel trim that goes around the glass. We highly recommend that you avoid the Chinese reproduction pieces, and stick with originals. We send large batches of used OEM trim to get professionally restored - see links below. We also go into a little detail about the trim clips and posts.
All in all, the process isn't as hard as it seems. We hope this video helps!
1967-68 Windshield-related parts: secure.cougarp...
Restored stainless trim (front, 67-68): secure.cougarp...
For the windshields themselves, we usually recommend that you buy them from a larger supplier or local glass shop with free shipping, as we're not able to offer that here.

Опубликовано:

17 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 45

@fireyman99 5 лет назад

Great installation video! 1. The use of weed eater string is just genius! 2. That transition to Bob Ross was fantastic. 3. Don Ross is absolutely hilarious! "The Joy of Cougars" Great work on this video!

@libertynbeer 5 лет назад

The Bob Ross references were fantastic :)

@glassguy777 Год назад

I've been installing auto glass for 22 years. I'm really impressed with this install. I've always used nylon rope for rubber gasket sets. But I really like the weed eater string. Your finesse with the install was stellar.

@cabledawg1967XR7_GT Год назад

Don, I have watched this video a dozen or more times over the past 2 years in preparation for installing my windows. Well, I just got done installing the headliner and decided to install the back window using this video. It was a piece of cake. Thanks for taking the time to show us how this stuff is done. If you happen to put the weed whacker cord starting on the top instead of the bottom, like I did, it still works.

@libertynbeer 5 лет назад

There is a whole array of pro-grade car glass installations tools, including caulking guns and tips. Might solve your weak tip issue. You can also use glass cleaner as a lubricant to get the seal over the glass easier. Tape the perimeter of the actual glass to make cleanup easier. The weed whacker cord is a novel idea, will need to try that.

@Robotguy123 2 года назад

I can't thank you enough for all you do for us Cougar fanatics. I have a love/hate relationship with my Cougar and the resources you provide keep the love high and the hate low. Thanks again for the quality products and the great videos!

@donaldleavy4379 4 года назад

I Think My Girlfriend Has Female Receptacle. Now that I think about it I’m sure she does. Thanks for reminding me Don, I think I’m gonna go check on that female receptacle right now. You’ve been a big help with this video thanks

@InsomniacReviews 4 года назад

Thank you for this! Great video makes me think I can do myself. Fingers crossed

@Timrsnakess 5 лет назад

Ive been waiting for this, the WCCC videos are the best, I have to replace my '67 mustang's windshield thats cracked on the passenger side. Also the Bob Ross segment was superb.

@bucko5301 Год назад

Quick tip, keep your strip caulk in the freezer. 1000% easier to apply, doesn't stick to your fingers so much, less mess. Try it.

@tmc.318 4 года назад

Thanks for all your videos. They are great!!. I had both windows out doing a headliner and then made an error I hope doesn't bite me. I had your video playing as I did the task. I watched several videos previously and saw some used the 3M caulk tube instead of the strip caulk in the pinch weld channel. When you strip caulked this slot it was a silent 7 seconds of your video. I missed it and caulked the wrong slot, the glass slot, before installing. So now my glass is in with no caulk in that pinch weld slot zone. I'm not willing to pull it out yet and start over yet because it took me an hour each window to get them in good. I hope the caulk applied around the seal from the outside will do it. I think I will try some mild compressed air gun to push the sealer deep. Hope it works. Appreciate the help.

@6T7CAT 5 лет назад

GREAT VIDEO DON! WHEN WILL YOU MAKE ONE ABOUT INSTALLING TRUNK AND DOORS WEATHER STRIP??

@donaldleavy4379 4 года назад

Watch Out For Worbles Don.. good vid.. You Just Kooky Man....

@richardnott9587 Год назад

I put tape under the edge of the windshield and after I put the caulk in it and press it down then I just pull the tape and it leaves a nice even edge.

@donaldleavy4379 4 года назад

Rrrrrrrrotatae That Trim In There Don.. Very good Don .. Now Your Using A Hammer On It .. Thats Nice...

@popssolo8366 Год назад

What is a good video for trim removal for a 1969 cougar ?

@kruno49 Год назад

Are the windshield seals the same for mustang (65) and cougar (68)?

@WestCoastClassicCougar Год назад

According to our supplier they are: secure.cougarpartscatalog.com/66z-6503110-1.html

@highdesertcougarcluboforeg7308 5 лет назад

Great video. I learned a lot. Thanks Don!

@mc66683 7 месяцев назад

Would you suggest the dash pad be removed or can it be done with that still in the car?

@juniortanguma4177 7 месяцев назад

I'm sure it can be done without removing the dash pad, but you'd be better off removing it.

@TheRaulr151 4 года назад

Great video. But there’s 2 things I’m dreading on my restore. 1) wiring and 2) putting that trim back on.

@67Mustang666 5 лет назад

The back glass for my 67 Mustang was a pain to install.

@rainman12345ful 5 лет назад

Great job, I have done 8 mustangs and i get my windsheilds from glassmasters cost 120.00 or less.

@callofgeorge 4 года назад

thanks for the vid. should make my first glass install on my 68 stang much easier. :)

@randomcarvids1052 4 года назад

Bedding and glazing is an old compound. Use dekaseal, or Sika 714 Outside of that great video

@patgulley5578 3 года назад

Great Vid WCCC. You mention the Mopar Retainer Clips. Do you have a part number? The video showed a GM Part?

@WestCoastClassicCougar 3 года назад

We have those on our website: secure.cougarpartscatalog.com/16830/30880/adjustable-clip-moulding-trim-retainer-front-windshield-rear-window-each-repro-1967-1973-mercury-cougar-1967.html

@twistedingeorgia1852 5 лет назад

Excellent video. The weed eater string is brilliant. Just a thought, if Vaseline keeps your fingers from sticking to the strip caulk, do you think putting Vaseline on maybe a rag and wiping the string with it to put a light film on the string would help it from sticking to the strip caulk and pulling it out of the channel during installation? I will be putting the glass back in my 68 cougar in the next few weeks and i think i will give it a go and see how it works.

@andrewc805 5 лет назад

Sounds like a good idea to me!

@twistedingeorgia1852 5 лет назад

I just installed my windshield last night using the vaseline coating on the weed water string. I had the seal In completely in about 30 seconds. There was barely any strip caulk on the string at all. Worked like a charm

@WestCoastClassicCougar 5 лет назад

@@twistedingeorgia1852 Awesome, glad to hear it!

@mando82jr 5 лет назад

@@twistedingeorgia1852 I just followed your advice on my 67 mustang front and rear windshield. Worked like a charm! I also put the strip caulk box in the freezer for 30 to 40 minutes prior to installing it. Helped reduce the mess.

@twistedingeorgia1852 5 лет назад

@@mando82jr awesome, I'm glad someone else is getting use from this tip.

@martingagne367 2 года назад

The weed eater string is it the same technic for the rear window of my 1971 cougar?

@WestCoastClassicCougar 2 года назад

1971 Cougar uses a glued in windshield, but the rear uses a gasket.

@dxrcat Год назад

Don, great video! Does the dash pad need to be removed? Thanks again

@juniortanguma4177 Год назад

No need to remove the dash, but you will need to remove the mouldings at the front of the dash pad.

@dxrcat Год назад

@@juniortanguma4177 Thanks so much for the advice

@NeighborhoodCarReviews 5 лет назад

Ha! The "Don Ross" section is funny. I hope the Bob Ross Company doesn't see it. They copyright strike everything.

@bcougard 5 лет назад

Great video, except I would leak test before putting the trim back on.

@timsmith1589 3 года назад

That doesn't look that bad at all.

@Chillyquack 5 лет назад

first to view

@banks412 Год назад

Fantastic video! I really liked how you got the camera in there to show the seal covering the inside when you pulled the trimmer line out. I would like to learn a bit more about the rope sealant - this is the only video I’ve seen that used it so far, but it looks way less messy than trying to put the caulk tube style sealant in that groove before setting the glass in place. I also liked that you emphasized taking your time and enjoying the time in the shop. Super easy to forget that for many of us, we’re doing this because it’s supposed to be fun! Will definitely be subscribing and watching this a few more times before attempting to replace the glass in my ‘65 Mustang. Thank you!