Hello.
It's very easy to order as you just need to order the dimensions you need and attach it as is.
Bolts don't require expensive special nuts, so that's helpful too.
The bottom plate is made from a flat bar. This is to ensure accuracy and strength, but plywood can also be used instead. In that case, it is preferable to use one that is not warped, but if it is, please set it so that the warp is directed towards the bottom. If it is facing upward, it will interfere with feeding the material.
For more information, please watch this video. I am using the steel version of the plate.
• 【木工 DIY】スライド丸鋸を100倍便利に...
About the high nut.
If the bolt is free, it will be very unstable and it will be difficult to tighten a normal size nut.
Also, when using a wrench, it is easier to tighten a tall nut with a wider area than a small nut.
About cap nuts and magnets.
The slope of the stop block in the video example is extreme, so in reality, the slope and error are much smaller, but it may still be affected. If I were to go into detail about this, I could make a whole video, so I did it simply, but another advantage is that it is not affected by chips or dirt.
It's very easy to do, just attach the cap nut to the magnet with double-sided tape. If you are interested, please try it out.
A similar effect can be expected by attaching cap nuts to the heads of all screws for fine adjustment bolts.
About stop blocks.
The reason I used steel is to use magnets. If you don't need a magnet, I think wood would be fine.
Just cut the L angle and drilled a Φ8mm hole for the mount and two M6 taps for fine adjustment.
I think there will be no problem as long as you decide the size and position according to your needs. The biggest advantage of making your own is that you can customize it.
Aluminum material source: Monotaro.
www.monotaro.com/g/02364602/
When I purchased the 2400mm in March 2019, he paid ¥4,533 (tax included). The price is now ¥5,623 (excluding tax), so the price has gone up quite a bit.
Monotaro offers free shipping for orders over 3,500 yen, and offers a 10% discount on all items about once a month, so it's a good idea to order at that time. Even beginners can easily install it by ordering the length they want and simply attaching it.
For this model (FC7FSB), anything with a height of 30mm that can use bolts is OK.
Please note that there are height restrictions on the motor side. 60mm was just fine.
If necessary, you can adjust the height of the cut or cut part of the fence.
Another option is to move the fence to a position where it won't interfere.
Even though it's aluminum, this class of material is heavy, so I don't think it's best to make it too long.
I have used it with a size of 2400mm, but I used it with two supports in between.
It would be better to think that one support is required for every 1000mm. In this video, we are using a 600mm miter gauge fence that is used on a table saw. With this length, no support parts are required.
It may be a useful component as it can be reused in various ways depending on your ideas.
Fine adjustment screw.
A push spring is inserted to apply tension.
To use it, just turn the screw and change the distance, so I don't think any explanation is necessary. Since the pitch of M6 is 1mm, it is calculated that one rotation is 1mm, but it is difficult to say exactly how many millimeters it will move, so I will turn it little by little and cut while watching the situation.
If you just want to make a small cut, there are other methods, but the most stable method is to use a fine adjustment screw.
About push springs.
Manufacturer: Yawata Neji.
Product number: C181.
Material: Stainless steel.
Wire diameter: 0.6mm.
Outer diameter: 7mm.
Length: 23mm.
Maximum load: 0.65kg.
Maximum compressed length: 7mm.
Where to buy: Cainz.
Fine adjustment bolt set with spring.
M6×20.
I don't know if this is the best combination, but if the spring is too strong, it will be difficult to tighten, so I chose this rate. It's difficult because if it's too weak, it won't hold any tension.
About bolts.
I use stock M6 x 20mm bolts. If you buy it exclusively, it may be a little shorter.
************************
Model used.
HiKOKI tabletop sliding circular saw blade diameter 190mm FC7FSB.
Thank you for watching.
Please rate highly and subscribe to the channel.
Translation uses Google's automatic translation. I apologize if it is difficult to read.
************************
Song: Luke Bergs & AgusAlvarez - Tropic Love
Music provided by Vlog No Copyright Music.
Video Link: bit.ly/41uQY1g
Song: Slowfy - Sudden Fall
Music provided by Vlog No Copyright Music.
Video Link: bit.ly/3mDnuiW
************************
#Sliding circular saw workbench #FC7FSB #Sliding circular saw #Miter saw #Miter saw station #Sliding circular saw jig #Woodworking #IDY #Circular saw #Woodworking jig
27 фев 2024