XR Build Guide - VOW 

1:01 - 20s2p main battery build 5:58 - boost battery build male / female xt60 connectors for i/o 12 ga wire bullet connector for charge + 2 pin jstph2 connector for balance control system 7:09 - install thor controller to lid w/ thermal paste 7:26 - LED install beginning (12v strips) 8:10 - connect wires to controller (wire charger connector: gx16 to female XT30) 8:27 - connect fungineer's motor plug (with heat shrink over the phase connectors) 8:41 - convert hypercore motor wiring harness to fungineer's motor plug 8:44 - cut motor wiring harness half way, strip wires, tin them 9:01 - determine how long to make the fungineers plug (don't forget all of the heat shrinks) hall sensor cable harness wiring: red - 5v white - temperature black - ground yellow / blue / green - hall signals 10:02 - test fit with rail 10:14 - cable harness (controller battery) make one end with all plugs, fit to decide how long to cut the other end connectors / wires: - main power line from main battery pack to boost pack - charge line from charge port to BMS charge input - battery positive line from boost pack positive to BMS battery input - two small balance cables with JSTPH2 plugs for 19th and 20th cell groups - 3 pin connector for tail LEDs 12:12 - install new hardness, tighten the M20 cable glands 12:25 - install LED and pickle BMS with mounting tape 12:36 - install thermistor for battery pack 12:40 - plug in everything. verify polarity w/ multimeter 12:58 - install lids (kapton tape where necessary to hold wires in place) neoprene sponge to provide light compression on the boost pack

Love the ending. Good recovery.

Great video .. just ordered my Thor .. might have to hit you up for some 12V LED strips and a p45B split pack. I was on the fence about installing the fungineers motor plug but after this video .. defo !! A++

Thanks for the content once again

Super video , Thanks my friend

Amazing 😮 I’m learning stuff! Your workmanship is top notch. Plus we need to check out Victoria Park 🎉 🙌🏼

Where did you source the super neat pre cut nickle? Really like the balance tab design.

The Oreos disappeared too fast!

Where did you get those battery pack jigs or does any one know where i can get the file to print them

Awesome board. Question. Would it be too much of a pain in the ass to measure your finished wires before taping them up so you know in the future how long each cable needs to be? I wish I could do what you do 👍🏻🤙🏻✌🏻

I'm interested in the specifics regarding the mounting of the thor300. Is it feasible to make an adapter plate to mount the Thor in a controller box meant for a lil focer? (eg Floatboxx MLC?)

Super confused on the boost pack why does it only need charger negative on main pack and charger positive on boost pack? I’m not getting how it’s a complete charge circuit like that? Wouldnt it just be charging the boost pack like this?

the led cage on the desk is neat, is that more uniform lighting or just rgb go brrrrt?

Could I use a Superflux motor in this build? I’m thinking the vow boxes and XR rails….

Is the sleeve of oreo's at 6:00 required for successful assembly?

How do you go about converting a board to VESC? How do you convert a GT to VESC? is there more to it than just a different controller??

Would you consider a split pack more risky for BMS or battery overheating/blowing up than a single pack?

Any idea on what range you'd get from this set up as its probably the exact same set up i want,

Could you put a 20s battery on a normal FM XR? Or is there a lot more to it? I am still trying to figure out how the whole onewheel system works.

I don't see anybody conformal coating the VESC board..... why not?

Would it be possible to do this with a onewheel+?

Brother possible to do the same for the GT build and list all the parts needed? The newb here will have to buy the parts and have someone actually build it 😅