No video :(

Yamaha Virago Carb sync on my XV700

Подписаться 881

Просмотров 15 тыс.

50% 1

This video shows me syncing my carbs.. here’s a few instructions on how I did it. Also, watching the video helps! Lol. Ok so instructions can look like this:
1) get engine to running temperature. Go for a ride.
2) connect hoses to nipples on manifolds. One on one side other on other side.
3) turn Petcock to pri and let bike idle.
4) close gauge valve just enough to steady the needles.
5) match both arrows by adjusting screw between carbs
6) rev a couple times to see any differences
7) rev and hold to 2k Rpms to see if it’s stable.
gofund.me/83d8...
Thanks for watching!!
#Yamaha #Virago #XV700 #Carbs #Sync #DualCarbs

Опубликовано:

27 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@shaneriggs640 4 года назад

Thanks for the video bro im doing this on a vulcan 500 tomorrow. Tia

@lui1760 4 года назад

riggs_ nation no problem man! Here to help others! Good luck! 🍀👍

@ambesa1 3 года назад

thank you for the video!!

@drumsk 4 года назад

Manual suggests the center screw is for 3-4000 rpm sync noooo But will try this next time

@lui1760 4 года назад

Ken PIccininni it worked great for me! Both sides started getting warm at the same time and fired up very well. Def should give it a try. Thanks for watching

@KevinBeGood 3 года назад

My bike started but then stalled when I removed the vacuum lines and wouldn't start again But started when I plugged them back in? My carbs also look slightly different but I have a 88 virago 750.

@lui1760 3 года назад

You might have a set of mukini carbs. The ones here are Hitachi. Those little plugs have to be capped off by a piece of rubber 😀

@janwasiluk4704 3 года назад

5. match both arrows by adjusting screw between carbs. Which screw is it in the video? Hitachi carburettors

@SpikeGABeen Год назад

Hi, Lui! Would you like to provide a link to the carb sync gauge kit you used?

@lui1760 Год назад

P1 Tools Motorcycle Vacuum Carburetor Synchronizer Carb Sync Gauge 2 Cylinder a.co/d/fASPQd6 I believe it’s these

@SpikeGABeen Год назад

@@lui1760 thanks, Lui!

@janwasiluk4704 3 года назад

You have not shown which screw you synchronize the carburetors, besides, the movie is great, readability is full.

@lui1760 3 года назад

Wow! I didn’t even notice that. That’s totally my bad. But if you do need to know what screw, it’s right between the carbs. It’s a gold Phillip screw.

@janwasiluk4704 3 года назад

@@lui1760 Thank you

@Ayadw7 4 месяца назад

Hey Lui, Did you have to do that after the dynojet setup?

@lui1760 4 месяца назад

Anytime you open the carbs, you want to double check by doing this procedure. 😎 I did mine because I had to mess with my fuel etc

@matthewnarron6894 Год назад

I have a 1984 Yamaha virago I was wanting to know if I could put two separate carburators on the bike like two cheap 350cc rateded carbs one on each cylinder set up the same way.

@lui1760 Год назад

How many ccs is your bike?

@matthewnarron6894 Год назад

700

@lui1760 Год назад

I’d definitely would recommend putting original parts like a Hitachi Carb or Mikuni carb. If you really want to go All out, I’d get a VM 38 flat sides. I honestly don’t know if 350cc carbs would work. They’re carbs so it maybe will work? Just gotta have the manifolds and intake seated properly and make sure you have your accelerating wire getting to both carbs.