Тёмный

Yaskawa GA500 VFD, remote control, MOP speed control, Multi frequency set up. English 

Ingus Sudints
Подписаться 26 тыс.
Просмотров 9 тыс.
50% 1

Yaskawa GA500 VFD, remote control, MOP speed control, Multi set frequency set up. For manuals, parts and related videos, please see below.
Yaskawa GA500 VFD CIPR-GA50CB002EBAA: www.ebay.co.uk...
Yaskawa GA500 Tech Manual: www.yaskawa.co...
Yaskawa GA500 Quick start Guide: www.yaskawa.co...
Yaskawa GA500 Core manuals, including transition from J1000 to GA500: www.yaskawa.co...
Website: igselectronics...
eBay store: www.ebay.co.uk...
Yaskawa GA500 VFD, local run, Commissioning, Auto Tune, Parameter set up Factory reset: • Yaskawa GA500 VFD, loc...
Yaskawa GA500 VFD, remote control, 2 wire control, 3 wire control, remote speed control: • Yaskawa GA500 VFD, rem...
Run a 3 phase motor on single phase power, basics: • Run a 3 phase motor on...
Single phase to 3 phase VFD drive home setup: • Single phase to 3 phas...
Single Phase / Tree Phase Inverter 3 Wire Control Station: igselectronics...
Single Phase / Tree Phase Inverter 2 Wire Control Station: igselectronics...
Multi frequency control Station: igselectronics...
MOP/Electronic Control Station: igselectronics...

Опубликовано:

 

5 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 8   
@sssssssssggggggg
@sssssssssggggggg Год назад
Late in the day Ingus - but you have saved my life. Thank you. I have a 22kw motor that needed to ramp up to 50HZ in 30 seconds. The load is heavy until full speed and no matter what I did - the drive tripped with OL/2 fault (over current for too long) I read the manual for multi speeds and it was defeating me. Your explanation and demo showed me how. I programed the speed sequence into a plc and paused between each ramp-up to allow the Amps to come down (65A down to 17A) It now reaches full speed with no OL messages. Thanks again.
@martinxxo15
@martinxxo15 2 месяца назад
Thanks for your explanation, wanted to know if you made the software video, didnt find it in your channel.
@IFoundThisNow
@IFoundThisNow Год назад
Hello Over there :) I wish that u make a video about using 2 different decelerations and accelerations, and use them for a 2 speeds. Regards
@sajek4246
@sajek4246 2 года назад
well done 👌
@josecarlosfranca6397
@josecarlosfranca6397 3 года назад
Se fala em português seria mais facil
@IGSElectronics
@IGSElectronics 3 года назад
Mas eu não sinto muito
@lucasrramenda
@lucasrramenda 2 года назад
O cara é Americano.
@خالدالقمودي-ذ6م
@خالدالقمودي-ذ6م 2 года назад
Realy ! u do an afaviur to me ! Thanks allot
Далее
ErieTec Educates - Yaskawa GA500 VFD Start Up
7:02
Просмотров 4 тыс.
Drive Basics
25:33
Просмотров 503 тыс.
How To Identify An Unmarked or Blown IC Chip
32:31
Просмотров 64 тыс.