ZERO Scooters hydraulic brake Install

Falcon Pev | Pab Pmd Escooter Ebike Shop Singapore

Подписаться 16 тыс.

Просмотров 54 тыс.

50% 1

The new Nutt hydraulic brakes is easy to install on the ZERO 9, Z10, Z10X and Z8X. This installation of the front brakes on the ZERO 10X is just an example of the steps involved but this applies to all models. The whole process if done by a non-professional takes one hour and no complicated tools are needed.
Here are the steps:
1. Remove the original red brake calipers
2. Plug and place the nutt brake calipers onto the original mount
3. Tune the brakes to ensure the brake pads are not rubbing
4. Thread the hydraulic brake hose through the frame using the old brake hose as a guide (there are many ways to do this)
5. Insert the valve cap into the other end of the brake hose and screw into the brake lever by tightening the nut
6. Test brake lever for tightness. Brakes should depress halfway.
7. Connect the electronic brake wires
8. Test e-brake connection using brake lights
For more information on the e-scooter featured, please visit www.falconpev.com.sg

Авто/Мото

Опубликовано:

5 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 115

@FalconpevSg 5 лет назад

Find these special brakes here www.falconpev.com.sg/products/hydraulic-brakes-for-zero?variant=15339841478

@FalconpevSg 2 года назад

You can also find the bleed kit here www.falconpev.com.sg/products/universal-bleed-kit

@declansmith1022 2 года назад

Can you guys make a video on how to replace new stem please. Mine is bent and I want to replace.

@merlingonzales1143 4 года назад

Hi falcon pev can you give some advice about the installation that im planning? 1. I have my previous hydraulic brakes from my mountain bike that is compatible with my eks particularly redline same with zero it has stock mecha nical brakes 2. It has no sensor. 3. Im planning to buy magnetic sensor for e-bikes, replace my stock sensor for my eks. Will this setup work? Thanks and more power to eks community.

@geestang2662 3 года назад

Do you need that special tool for the fitting in the end if brake line

@Bob_Lee 3 года назад

hey FALCON. Can I order these for a ZERO 8X?

@someperson4712 Год назад

For the hydraulic brakes like the manual ones. Can I lightly tap the brake to slow down but not completely stop?

@gautheny 3 года назад

Hello sir. How do these compare to shimano 6100 brakes in terms of braking perfmance if I may ask? Also how does this model do against its NuttA1 type counterpart ? (for mtb) Thank you

@johnalfredcanuel1784 4 года назад

This brake disk can i put it in zero 8 front?

@tomsavine7444 5 лет назад

Thanks guys, I have a set of these on the way. Do you know what upgrade suspension can be used? I assume 165mm standard shocks... would 180-200mm work do you know?

@gray_wolverine63 4 года назад

I like to know also.

@adarapjan 3 года назад

The olive connector, which reference is? Due I live in South America I want to know if the sram olive conector is suitable for nutt breaks?

@wattsnb 5 лет назад

Nice. Do they need bleeding/purging following install and if so how? Thanks.

@gray_wolverine63 4 года назад

I want to see also but they dont back as I see, guess we need to ask someone in a bike shop or have it done by someone at a bike shop who know about hydraulic breaks.

@chefgav1 3 года назад

Rocky Hernandez video said pre bleed

@rbmanb 3 года назад

Is it worth it to Install nutt hydraulic brakes on the 52v version? I can get a deal for the zero 10x + the hydraulic + installation + wobbling clamp for about 1500 usd, take the deal?

@garylinnert1574 4 года назад

Thanks for doing this video. Want to know if these brakes will also fit up to a turbowheel lightning scooter like the zx-10. Also what are the tires you have mounted ? Are they 120/90-10-57 Michelin reggae type ? Look forward to your reply and thanks again...

@FalconpevSg 4 года назад

Gary Linnert no idea if they will fit that model. It’s not the same.

@garylinnert1574 4 года назад

@@FalconpevSg Thanks for your reply. Will keep looking for the answers. Cheers GL

@d4rkloler 4 года назад

is there a specific needle head size that's required for this? I bought a kit for my zero 10x and the needle heads weren't included.

@dwanecrow3622 4 года назад

Dalset I have the same problem I bought the kit from REVRIDES.com and it did not come with a needle bolt for front or back.

@bogdan9 5 лет назад

The wheel and brake disc are almost the same size so break power is very good even with the original breaks. What I would be interested in are ABS breaks.

@FalconpevSg 5 лет назад

bogdan9 ABS brakes are actually electronic braking in the controller not in the actual brakes itself.

@brounstoun 5 лет назад

Do these hydraulic brakes require special brake pads? Or can I use original brake pads?

@FalconpevSg 5 лет назад

Matt Brown it comes with brake pads. But yes it uses special brake pads

@michaelosullivan4112 Год назад

Zero 8,9&10x needed front stem neck like zero 11x that be cool if they had in all lined up for mad collections 🙏🙏 ✌️✌️

@josser0 4 года назад

Can I use this to replace rear drum brake on Zero 9?

@gray_wolverine63 4 года назад

I don't believe you can buddy.

@Chandaman14 Месяц назад

What is the tool called to insert the valve into the brake line?

@Remarkyt 4 года назад

hello there i want for sure to purchase your hidraulic braking set up...but there is the problem...in video you are cutting the wire.is necessary to cut?

@FalconpevSg 4 года назад

RemarkablePoint no it’s not necessary anymore. We made it easier. Search for our latest zero 10 hydraulic brake video.

@Remarkyt 4 года назад

Sorry also I was thinking about you are cutting the hydraulic wire...

@powt.vmonitor9966 4 года назад

pls advise me where i can place an order of zero 10x or 11x? thanks in advance

@FalconpevSg 4 года назад

pow T.v Monitor www.falconpev.com.sg

@ReelyCatchy100 3 года назад

hi is it a diffrence if you allready have zoom brakes on the zero 10 x ? mine has the zoom brakes an i have an issue with the rear brake i want to switch it to the nutt brakes

@FalconpevSg 3 года назад

Nutt brakes are indeed better. Made in Taiwan Nutt brakes are used on many high performance scooters

@Maltmeister1 4 года назад

How do you top up the mineral oil reservoir.

@FalconpevSg 4 года назад

Ray Scott find on RU-vid how to bleed hydraulic brakes

@genz0r 3 года назад

does needle and olive from shimano breaks serve for this?

@adobeauditionandaudioboxit519 3 года назад

it is easy to miss but the olive and needle are included in the nutt brake pack. The needle is under the little cap at the end of the hose. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-PYrPfy2GTmI.html&feature=emb_logo this video helped me understand that!

@Nosci1020 5 лет назад

Where can i find and buy that needle hose tool?

@Zero-wt7xf 4 года назад

any online bike part supplier have them pretty cheap.

@A-Viking 4 года назад

If my scooter is going no faster than 25km/h is there any real benefit of upgrading the brakes like that?

@FalconpevSg 4 года назад

A Viking hydraulic brakes are not needed at that speed.

@oliveraidoo7861 2 года назад

Hello, thanks a lot for making this video. I have the EMOVE cruiser electric scooter and need to swap the brakes from mechanical to hydraulic. First, I want to know how well yours work in wet conditions. Secondly, is there any place/physical workshop I can visit to have that installed? Lastly, anybody to contact? Thank you!

@FalconpevSg 2 года назад

You can bring it to rev rides or try doing it yourself?

@oliveraidoo7861 2 года назад

@@FalconpevSg Thanks for replying. I am currently in Croydon (London). Do you mind if I ask for the address/location of Rev rides?

@FalconpevSg 2 года назад

@@oliveraidoo7861 if London definitely recommend PET personal electric transport

@oliveraidoo7861 2 года назад

@@FalconpevSg Okay man, thanks a lot

@Pirelli. 3 года назад

Hi everyone: I have the Yume D5 scooter and I want to install the brake too. do I have to solder the cables for the e-brake together and why? I thought it would work if I just cut it off?

@FalconpevSg 3 года назад

Depends on whether you want ebrake.

@Pirelli. 3 года назад

@@FalconpevSg I don't want this e-brake. I can do without it because it then brakes too hard and is not good for the engine. so can i leave the cables open without soldering?

@FalconpevSg 3 года назад

@@Pirelli. yes you can leave it open no problem. But you can actually reduce ebrake power by adjusting the lcd settings

@Pirelli. 3 года назад

@@FalconpevSg OK thanks. then i will remove the cables. I don't need the engine brake anyway because it brake too hard for me.

@josephkadabra6396 3 года назад

My handle pulls all the way back before the hydraulic brakes engages how do I adjust that?

@FalconpevSg 3 года назад

Joseph Kadabra you may need to rebleed the brakes. But a way around it is to double pump the brakes

@Splodgo 4 года назад

I recommend higher quality washers. Those conical washer can easily slip and scrape on the disk.

@FalconpevSg 4 года назад

Splodgo conical washers are typically used to adjust height on brake Calipers.

@dwanecrow3622 4 года назад

Any suggestions on how to press the brass needle fitting into the tube ? I don’t have the press tool there using or can you supply a link on where to purchase one.

@FalconpevSg 4 года назад

dwane crow actually you don’t need the tool. Look at our other hydraulic brake video to see how to do it

@dwanecrow3622 4 года назад

I have a zero 10X I bought the nutt hydraulic kit and watched the install video thanks unfortunately my kit only came with one collar so I’m headed to the bike shop on Tuesday.

@FalconpevSg 4 года назад

dwane crow not sure where you bought from but the ones from us works like this: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Kew7gYhGvUM.html

@dwanecrow3622 4 года назад

Falcon PEV I bought my 10X through REVRIDES.COM

@Deycallmeslimey Год назад

My leaver goes in all the way how can I fix it

@acidkhmer 3 года назад

I've bought you're zero10x kit for my vsett9, do I need to cut the tubes? Or it will be OK? Ty

@FalconpevSg 3 года назад

Can you email us and we can help you with it

@acidkhmer 3 года назад

@@FalconpevSg ok thank you

@acidkhmer 3 года назад

@@FalconpevSg email sent ;) I need to know, if I need tools and oil brake, or it can be ok with your prefill tubes, cut size.

@9superandry 4 года назад

Where can I purchase this brake set in Europe ?

@FalconpevSg 4 года назад

Andrea Ciuro only on our website

@pinoymovieexpress1746 5 лет назад

Can it also use it to zero9?

@FalconpevSg 5 лет назад

Alex Komang yes it can

@gray_wolverine63 4 года назад

This nutt hydraulic brake comes as a front and rear set for the price ?

@FalconpevSg 4 года назад

yes one set front and rear.

@gray_wolverine63 4 года назад

@@FalconpevSg Thanks 👍🏼

@jhonathandio1 2 года назад

Can I do this for apollo explore

@FalconpevSg 2 года назад

Yes should be ok

@assassin8r 3 года назад

Hi, I have a zero 10x and I'm getting an error code on the display with flashing rear lights and the throttle doesn't work. I've tried pressing the brake 3 times on each side that doesn't work. Can you tell me what the white and yellow wire does, also black and black? If I disconnect them will it fix the code? I'm guessing it's just a signal for the electronic brakes. Thanksb

@FalconpevSg 3 года назад

What error

@assassin8r 3 года назад

@@FalconpevSg I think it's a brake sensor error. It's the (!) on top right of the display. The rear brake lights are flashing but there's no reaction when I press the throttle

@FalconpevSg 3 года назад

@@assassin8r the brake sensor could be spoilt. Try removing the brake sensor?

@assassin8r 3 года назад

@@FalconpevSg where is the brake sensor located?

@ElectricunicyclesUK 3 года назад

Will oil come out the cable when you cut it and then need re bleeding?

@FalconpevSg 3 года назад

You must cut the cable and insert the olive pin

@ElectricunicyclesUK 3 года назад

@@FalconpevSg will it fit the kugoo g-booster thanks

@FalconpevSg 3 года назад

@@ElectricunicyclesUK don’t know what that is

@stavgolan4320 2 года назад

Hi How to add front motor for 10X And what parts are needed?

@FalconpevSg 2 года назад

Zero 10 or 10X? 10X already comes with front motor

@stavgolan4320 2 года назад

@@FalconpevSg for Zero 10X

@rbmanb 3 года назад

What do do if my new hydraulic brakes are still noisy? I'm having hard times adjusting them.

@FalconpevSg 3 года назад

What kind noise?

@rbmanb 3 года назад

@@FalconpevSg the pad is rubbing on the rotor. I managed to tune the rear wheel, just releasing the screws and then holding the breaks while closing it again. For some reason I have some hard times doing the same thing in the front wheel

@FalconpevSg 3 года назад

@@rbmanb new pads?

@rbmanb 3 года назад

@@FalconpevSg yes. Okay! Done! Just had to release and and strengthen it twice more... But now no sound.

@Goodman-4525 3 года назад

No the pads shouldn't rub at all even when they're new. And you can centre the calipers by loosening the bolts and clamping down the brakes

@boke75 2 года назад

5:48 "No complicated tools are needed". Apart from that special brake line plug insertion tool. 😂

@FalconpevSg 2 года назад

That’s a regular brake item

@declansmith1022 2 года назад

Hey everyone. I put my zoom brakes back together but my brake lights are flashing and it won’t move. Can anyone help me please.

@FalconpevSg 2 года назад

Did you connect the ebrake wire properly?

@declansmith1022 2 года назад

@@FalconpevSg what is ebrake wire ?

@FalconpevSg 2 года назад

@@declansmith1022 if you didn’t know what that is then there is something missing in your installation

@declansmith1022 2 года назад

@@FalconpevSg i put everything back the way it was before.

@declansmith1022 2 года назад

@@FalconpevSg do you have another way i can contact you and send photos please.

@pablopeillard8810 Год назад

your comment is not correct. If rotor ( disk) is larger you need a new spacer, never use washers

@FalconpevSg Год назад

We use Spacer washer interchangeably maybe not the correct term but the idea is the same

@TheSecretBaller 3 года назад

you keep skipping parts

@FalconpevSg 3 года назад

curious to know which part was unclear?

@TheSecretBaller 3 года назад

@@FalconpevSg connecting the brake cable to the lever, well i had to watch another video to realise that i didnt need to drive the needle head to cable, as mine was simply to put the olive in before connecting it. Also the removal of the original brake levers wasnt shown and were to cut it

@FalconpevSg 3 года назад

@@TheSecretBaller so it isn’t skipping parts. We don’t show what you don’t need to do.

@TheSecretBaller 3 года назад

@@FalconpevSg I disagree, firstly cutting of the brake levers (e brake cable) is needed, which wasnt shown from the start. I thought there was a connection that i had to unplug and had no idea which wires to cut. Secondly the process of installing the new brake cable to the new levers is different (for the 10x) as no pin is need to be pushed in before insertion.

@FalconpevSg 3 года назад

@@TheSecretBaller anyway if you look at the video it was taken more than a year or two years ago. Parts have been changed so some parts are outdated. But in general the concept is the same and that’s what we are trying to promote. A detailed tutorial is not what this is meant to be.