@@markbogle4784 Look, I'm not trying to be funky here but these are not meant to be used to jack up the car. These four points at the corner of each wheel well were designed to carry the shell of the car (no interior or drivetrain) during assembly. They will collapse under the weight of the car once lifted. The manual actually shows you exactly where to jack up the car. Just sayin'
Thank you very much for sharing. I had the same problem with my 2019 Sienna. When my phone was connected, I couldn't make the other party hear me when I was on a call because the car's microphone didn't work. This problem was solved by disconnecting the car's battery.
Having exactly the same problem! After cleaning every part and putting it back together, I was able to load again and I thought problem solved. Not so fast ! After the second load of line the problem returned and I had to go through the same procedure again. My next step will be, is to replace the original EGO head with an Echo speedfeed 400 universal head. It will not be fully automatic, but it will save a lot of time not having to disassemble the original EGO head. Other than this issue, it is a fine machine.
I had the same issue. I used that 928 collar/sleeve and worked like a charm. I actually used a 2nd gasket to get a better seal. I also have a ‘87 turbo and I didn’t modify the sleeve to make it fit. I used two different JB Weld epoxies and they both failed before I found this 928 sleeve. I conclude that JB Weld is for temporary fixes, not permanent. I’ve had mine on for about 2 years now.
I have to press and pull on my driver side l. I already tried grease and nothing, what could it be ?? I also notice that the main door hinge is not attached and there broken screws, it's only been held by the upper and lower hinges ..
Not sure what you mean. The repair piece is aluminum and it replaces the aluminum female threaded boss that was originally molded into the tank. The strainer is identical to the original and has an aluminum fitting with a plastic strainer.
So, my microphone wasn't working, my front passenger side speaker stopped working, and the SOS system stopped working. I used this reset method to try to fix the microphone, and it fixed all three issues.
Check engine light came back? P1130 is on the other side of the engine, bank 1 sensor 1, right below next to the bottom fire wall. California has its own O/F mixture sensor requirements and more expensive. DENSO should come with a little anti-seize compound, no?
That is 1 of reason why I am hesitating buying a power head. Everything you buy today made not to last long with plastic parts. Is it worth aggravation? How old it the head ?
I bought the same trimmer recently and the bump-head lasted only a few hours of use before the automatic line feed mechanism failed. I fixed it using the technique shown in this video, but Ego have made a poor quality product if it fails after such a short period of normal use. At least the manufacturer warranty is five years, but I could do without the hassle of returning the equipment. Such a shame as I quite like most other things about the product.
Hey dude, those JBL work with 3OHMS impedance, wich stereo system are you using? As faar as i know, almost all Stereo radios, work with 4OHMS... i just made this mistake... having speakers working with less resistence than the stereo, will overhead the stereo causing to burn... untill that happend, either the stereo doesnt work, or work but the sound quality will be much under the standart from the speakers.
Agreed about making that part available w/o buying an entire new motor - that is gouging and wasteful. My weed eater has the same problem, and this is the first time I have seen the issue even addressed - you have done a great job figuring this out. But meanwhile I actually bought a new weed eater and want to put a blade on this head and just use it for that. Unfortunately, the configuration after removing the power head does not match what I see online. The others have a deep cup that when removed reveals a smooth metal plate - this weed eater has a shallow cup and (not smooth) plastic under it. - I'll use your ingenuity for inspiration! Thanks for making this video - I did gain information that is useful for what I'm trying to do, and I appreciate it!
This is exactly why they make this shit another country so you can’t go down the street and kick their ass. This is the exact same thing wrong with mine and they won’t do nothing about it. They actually told me they would fix it but they would cancel all the warranties on all the other tools I own. wTF
I did the same exact mistake as you with the handle latch not being seated properly when refitting the handle after a repair. Now my door won't unlock and I'm pretty much where you started this video out. Wish I had a video probe now...
@@ThingsBreak Thanks! I forgot to update here, but I did just that, but with no luck. I eventually borrowed a video probe from a friend and managed to get the door open in the same fashion as you. This video was of great help!
Ego SUCKS. Tried calling customer service today was on hold for almost an hour. No one ever answered. So i am now waiting for a call back. I bet i never get that call back. Also, the newer models don't have a keyway and still have the same problems.