Yes sir it should be fine

@@RigoG09 I did some more research into it, and I would also have to swap the rear shocks. The shocks are sized for the 6” lift. My next concern would be the blocks under the airbags

@@Ryansanders729 Yes if you have the shocks for a 6” then yes those will have to be replaced as well, the shocks under the airbag if you have the stock ones they will work as well but I think you have the 5” ones if your truck is lifted at 6”. But just swap to the OEM ones and you should be fine.

Yes, luckily the shop that installed the leveling kit did the alignment as well

Yes sir, I didn’t use the OEM running light I installed a different LED Strip. I have a video on it. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Fp-K4V148Lc.htmlsi=7RknNPx6GYUsZkgh

Thank you

I got it from phoenixautomotiveinc.com

It would be great if you had the part numbers listed.. I told stage3 that you gave them a shout out… lol but they had no idea what parts I would need..😔😔

Yes you can use the original blocks, but it would sit a bit lower the 3” blocks would be a better height.

Yes you could use it also, although if you don’t have a 6” lift already with the new crossmembers you could just get the 3” coils and new uppers to correct the angle.

I have the 6” lift

@@JasonWood-vj2rk In that case then I believe that 3” kit will make your upper control arm higher than normal since most of the front suspension is already dropped with those drop brackets that come on the 6” lift.

@@RigoG09 thanks.

Possibly not I think you should be fine those newer tahoes have bigger fenderwells

Its a 2.5” readylift leveling kit.

No sir I don’t have a video on that

Wasn’t too bad just pop the clips on the sides of the foglight and pop the new ones in and thats it.

Sweet thanks for the reply brother. I placed my order this morning, great vid!

@@davidg5965 yes sir no problem

I believe its possible, I had an XLT as well but I changed the badge on this truck to LOBO. I say I had bc I sold this truck over a yr ago.

@@RigoG09 where can I get a LOBO badge?

@@alejandrorodriguez3239 I ordered mine off Amazon, and I just repainted it

got them from amazon but I opened them up an added the led strips

It's ran to an add a fuse in the fuse box inside the truck

I used a thicker needle or you can use a mechanics pic

I just grounded it to a ground right there on the amp board. For power just ran a wire and then added an add a fuse where the fuse box is at and thats it. Around 20:15 it shows a little bit where i ran power to it.

What fuse specifically?

@@marvelislife2467 #19 the radio/battery fuse

Yes, just leveling the front is enough.

They are anzo tailights bit were retrofitted with that red led strip. I haven’t seen that strip for sale in over a year so I don’t think they make them anymore.

Thank you thank you. I’m from Georgia and I travel a bunch I’m usually not home for most part of the year.

I sold the truck about a year ago, I don’t have pictures

I bought the kit from the rough country website.

I don’t have the link they stopped making this product about 2-3 yrs ago. The next best kit I found was off pro clip usa they have mounts as well.

Yes sir thank you

Thank you

I put it behind the driver seat on the pillar.

How did u connect them

I connected them to a fuse on the passenger footwell fuses. Just a 12v circuit with an add a fuse is ok

I just did a light sand with 600 starting moving up to 2000 grit. Then primed, and did base coat. The clear though you have to make sure its at least 2K clear if spraying from a can now if you use the gun it would be better but I used the 2K clear from a can and its held up nicely.

Thank you so much bro I thought you wouldn't reply since it's been two years but your truck came out sick I just got Mines last week same year same color bro and I loved how you left t

@@vanpiroto Thank you bro, yeah it took some time to get it done but it was worth it, glad I could help.

On amazon they were anzo headlights, but I replaced with these, www.amazon.com/AmeriLite-2011-2013-Switchback-Projector-Headlight/dp/B09WMSQL42/ref=mp_s_a_1_2_sspa?crid=36B39NTE6XT6I&keywords=2012+jeep+grand+cherokee+headlights&qid=1696431172&replacementKeywords=headlights&sprefix=2012+jeep+g%2Caps%2C88&sr=8-2-spons&vehicle=2012-42-349------------&vehicleName=2012+Jeep+Grand+Cherokee&sp_csd=d2lkZ2V0TmFtZT1zcF9waG9uZV9zZWFyY2hfYXRm&psc=1

Oh yes we still have it just replaced all the fluids in it and still runs strong has a little over 245k miles

@@RigoG09 how about the painted trim how is that lasting?

@@RandomRichZ Actually its lasted up until the last month starting to chip but only on the corner of the small rear glass maybe I just didn’t sand as much there bc its both sides but all four doors still holding good.

Oh yes for sure I love this style better

I got them from custom offsets.

Nice brotha thats a clean look.

Any pics I want to level my Tahoe how’s the ride quality

@@MrInternationalSound I have a picture but not sure how to post it. Ride quality is fine, but the Escalade has magneride anyways which has 2 new front shocks done within the last year