Welcome! This channel is intended to help you to do your own repairs with short clear video guides. These videos are educational videos only and ALWAYSAFIX will take on no responsibility for any damage you may cause by trying to do it yourself. Even if you do not attempt the repairs yourself these videos will help you understand what is the fault and that will save you money when it comes time to send it in for the repair. You will also find advice on your repair in the forum. Thanks for your visit and may you find your FIX here from one of these videos.
For extra info on the repair, please visit the website.
FYI, it would very helpful if 1) you showed how you hooked up the multimeter for the voltage test. ...2) showed and explained in more detail the amperage test setup. People who can read between the lines, will already know, what basically to do already.
lol i had this problem witha 1080 all i did was solder on a motherboard fan plug and plugged the fans into the motherboard. worked till i got a new card
Great job! The only issue with Windows 10 is that (at least here in the United States) security updates will run out in October 2025. Although you can pay Microsoft for extended security updates.
Thanks! Didn't realize that the second hand on the clock above my printer had fallen off and ended up inside the printer. Took a little time to find it, but I did. So I don't need a new printer after all. Yea
I have a philips that as a white screen but also can some black vertical lines , still get sound but no picture . Could this be a t con board or will it be a dead lcd panel ?
Does the TV display the same on every input source? Does the menu display? It could be be either, but first check for loose cables, especially to the T-con. What is the model?
@@alwaysafix it's a philips 58pus8555/12 I unplugged the SL cable from the tcon and the right side worked perfectly. So I put a bit of tape over a few pins on the SL cable plugged it back in and it worked apart from a small watch patch in the bottom corner . So I tried putting the SR cable into the left side but still in the right side on the tcon board and that side just went fully black but nothing displayed like booting logo etc . So I put the ribbon cables back to the correct places and tried the tape again on the SL cable pins and I can't achieve the picture I got the first time I tried with the tape . The SL cable as a few creases on could a few lines be torn inside ? Can a tcon board fail on just a couple of feeds to the SL cable causing the whole thing to trip when both plugged in ?
@@alwaysafix is there a way to check each pin on the ribbon cable with a multimeter? I'm getting people saying to check things like vgh vkl on the tcon board , then check the cof strip on the side , but this tv just as the 2 cables from the tcon board into a strip at the bottom of the screen . Do I check points on the left cof to see how far signal is reaching along it ? Could I plug the SR cable into the left side of the tcon board to the SL side cof strip because I know that side works and I would eliminate the SL ribbon being at fault ?
@@CM-1723 You can not swop those ribbon cables left to right, the pinout is different. If you cannot see physical damage on the ribbon cable it is not damaged, that cable has no stress on it. I am still suspecting the Tcon board.
Good afternoon They say that in the latest releases of AD210 there is an undocumented ability to connect the microscope to a PC (not with a standard cable, but with a regular USB).
Can we use anything else than contact spray? something similar and easily available? Secondly, my headphones are new there is no rust or any kind of debris in it? it is not charging. like current flows (the wire overheats - tried with other cables too same issue) but headphones not charging...
Thanks for doing the review, I have just ordered this scope from AliExpress for 86€ delivered, I have also ordered the AD106s from amazon for 80€ (I ordered the AD106s from amazon earlier today) and then found this one whilst watching RU-vid videos on it😂 so I will see which is best, probably this one is, but no problems in sending the AD106s back to Amazon within 30 days if i need to. It will be used for pcb, refloating and soldering work. I feel this one AD210 better suited for this work due to having more clearance space for working with the tools. Again. Thanks
I have been using it for micro soldering, and for the price I am very happy. The AD106s has a small screen 4.3 inch where as the AD210 comes with a 10 inch screen so that should seal the deal. Good Luck.
Antec bp450p blown Symptoms: blown fuse, flown mosfet and diode. Replaced all. 5v on pson and 3.3v on vsb standy coming. Vsb seems faulty. Starting with the green connected to black, series lamp lights up. Thinking output is short. Any other ideas (I'm taking this slow)?
Since the series lamp lights up your problem is on the primary side not the output. When the mosfet shorted it damaged other components. Check pinout on main control IC. Good Luck.
bro please help i got the exactly same headphones, the issue with charging port... its not working How to fix it? like i try buying a new cable but even with new cable the headphones are not charging. Everything else working fine. i bought them last month, working fine but now facing this issue from past 3 days. please help, i wanna fix them myself. i take them to near repair shop but they always make fuss out of nothing. according to them the only issue to any problem is buying new one.
@@allmovies-hr3iq Press and hold power on button until it turns off. Power on then keep tapping spacebar key until you get the option to skip disk scan.
