I hate when I walk into a job and see this type of texture. I always try to talk the homeowner into orange peel instead. I'd rather skimcoat the whole house than use this product. It's rather inconsistent. FTS!!!
When my fass motor dead my trucks engine would cut in and out like that acted like a gaint boost leak with no noise at all just blowing the fuel outa the plug
Im here just to see if there was a trick to get out without removing the seats. But once the a,b,c pillars are pulled I was able to get a on the back side. Slide headliner forward and there is a notch that you can place those on the back side as well. As for the wire figured it was a 19 yr old truck so just pulled it away from glue. Enjoy those yrs with the little ones they go by so quick
@@ynot8u2 Sounds like you got it! pulling it way from the glue is fine too! I ended up folding mine slightly to get it out. Some fold and some take the seat out to avoid a crease. Mine didn’t show a crease from folding. I took mine out the rear door as well helps. The seat is heavy fyi and requires big strength and two people. The seals and trim can get torn very easy.
@Zacpactv those are the pins I removed, thinking they were locking the handle in place. I found one and had to switch it back and forth while I worked the handle out, one side at a time.
if it runs good, yes if you can test the mower out in grass thats a plus! To see if it has bogging issues. I traded this mower off. One of the best i have owned. Check hydro responsiveness good.
Had the same problem, it was the powder Cascade, I have used this brand for years. I changed to Finish quantum tabs and problem solved. Never go back to cascade again
@@Zacpactvcan you post a link of part? I got a 03 lb7 and it does the same but even worse, when hot and in full throttle w a trailer and mowers it pops like it’s banging off rev limiter
The wind overpowered your voice. Mostly unintelligible. Two choices, get a microphone with wind shielding, OR add the narration while editing the video.
Great Videos! Thank you for sharing. A can of Silicon spray to spray across the channels before sliding the new seal in is a big help. Just a suggestion. Thanks again, your video's are very helpful, nice job!
Fixed the problem, bought 2 actuators and same problem, I opened the old one to see what was the problem and after studying the actuator, I saw that the contact pins on the black gear would barely get out of the contact board making the problem of not opening or closing. I rolled up small rags to zip tie them to the plastic rail on the blower motor where the vent door rest, set the actuator to the middle, installed everything back and works like new. (The rags stop the inlet door from fully opening so that the pins stay on the contact board)
Perfect video!! Mine had a horrible rat smell! Turns out they nested up under the windshield air intake. Had to remove the plastic grille and got a water hose in there to get everything out of there. A little water made it in the cab, luckily rubber floor mats caught the piss water. I soaked the evap coil and intake ducts with green clean and will get after it tomorrow again. That’s what happens when you let your truck sit I guess!!
This comment has nothing to do with your current video, so I apologize in advance. But I was curious if you could help me with how you converted your kids sehomy tractor to a 18v battery? Thanks!
No problem, you have to splice into the bigger red and black wire to make this work. I recommend using a knock off battery to the brand of adapter you install. The drills that these batteries come in have a resistor that keep batteries from being drained to 0%. So using your good batteries is not a good idea unless you an aftermarket protector. I would recommend watching a conversion video on youtube. The easiest way is to hard wire without a low voltage cut out. I would also wire an inline fuse to protect from a short which can cause a fire!
Im still impressed with it. I have 4 or so batteries that I cycle out. I have a chainsaw as well and plan to buy a blower. i have a play set, trampoline and fence to trim around. I would not recommend for heavy use but I trim almost a half acre yard with it.
thank you for this my Dakota has horrible bedrock and I'm going to give this a shot I'm guessing thank you for this my Dakota has horrible rot in same spot
I just picked up some cub cadet paint at tractor supply. It didn’t look very close inside of the store but when I looked at it in natural sunlight outside of the store, it was a much closer match. Hopefully it’ll look even better once on the mower.
I actually did mine last night and I use an orbital sander with a 40 grit sandpaper took it right off in less than 10 minutes. I had it done with no damage to the surface underneath.