Тёмный

はんだ付け。CANARE F-09 RCAプラグと、mogami 2534 ケーブルで作るオーディオケーブル。レコードを聴くようなピュアオーディオに良いと思います。 

Shippo Nosaki
Подписаться 895
Просмотров 14 тыс.
50% 1

Опубликовано:

 

29 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 23   
@biggles5633
@biggles5633 2 месяца назад
Excellent video, just what I have beeping for ... arigato!
@petarJK
@petarJK 7 месяцев назад
I think you could go with less soldering material. Good video!
@soundmap-Y
@soundmap-Y 7 месяцев назад
Thank you for your comment. As you said, the amount of solder used is a little large. With my camera, the proper amount of solder makes it look thinner and less when photographed. This reply was written using Google Translate.
@duksangcho2448
@duksangcho2448 3 года назад
Thanks for your explanation. In general, I understood that if a cable does not have a ground loop, both ends of the cable are the same. What are the characteristics of cables made this way? I know that the l-4e6s cable is also wired in the same way.
@soundmap-Y
@soundmap-Y 3 года назад
Not everyone has the same idea, but I've experienced that mesh shields can be unreliable. It would be nice to have a very fine mesh, but the work is difficult. Originally, I expect one of the two cores for the balance line as a good quality GND parallel to the hot side. Well, it's my favorite. in addition. .. .. It seems that many 2-core twisted cable (4-wire) products are of good quality.
@duksangcho2448
@duksangcho2448 3 года назад
@@soundmap-Y Thanks a lot.
@tn9274
@tn9274 Год назад
is the braiding intended to be soldered on the crimping arm? it looks like the cable jacket melt a bit.
@soundmap-Y
@soundmap-Y Год назад
Thank you for your comment. I always solder the shield mesh. As you pointed out, the coating will melt at the clamp part. I think it would be practical to solder only the wiring holes and tighten the clamp sufficiently. The method is to connect the shield without using solder (crimping), but in the case of the plug and cable combination shown in this video, I think it is not enough to just tighten the clamp. This reply was written using Google Translate.
@tn9274
@tn9274 Год назад
@@soundmap-Y agree, crimp the shield is not tight enough. if the shield joined together with the ground and soldered at the opposite side of soldering hole, it will be too thick and touch the plug shell.
@Michael-of6ju
@Michael-of6ju 2 года назад
Good 👍
@IliyaOsnovikov
@IliyaOsnovikov 3 года назад
I use Canare F-10 RCA plugs. I guess they could be somewhat beter than F-09 because they have teflon insulator.
@soundmap-Y
@soundmap-Y 3 года назад
I think the F-10 is an excellent RCA plug. In this video, I thought of a cable that is easy to use even for small devices.
@IliyaOsnovikov
@IliyaOsnovikov 3 года назад
@@soundmap-Y Also I like Mogami 7551 RCA plugs. Have you ever tried those?
@soundmap-Y
@soundmap-Y 3 года назад
@@IliyaOsnovikovI haven't tried it yet. It's a cool plug. I think it will take some time to think about what kind of cable is interesting.
@duksangcho2448
@duksangcho2448 3 года назад
I saw the video well. Are the wiring at both ends the same?
@soundmap-Y
@soundmap-Y 3 года назад
Both have the same wiring. The blue wire is used as a GND shield. Sorry for Google Translate.
@soundmap-Y
@soundmap-Y 3 года назад
Sometimes the mesh shield is only on one side. When you want to avoid a ground loop.
@azzinny
@azzinny Год назад
5:44 My feeling is that we should crimp first, and then solder.
@soundmap-Y
@soundmap-Y Год назад
I always think about what to do. I often work according to the steps in the video. I'm thinking this would be easier to make.
@duksangcho2448
@duksangcho2448 3 года назад
映像も見ました両端の結線が同じか?
@soundmap-Y
@soundmap-Y 3 года назад
両方とも同じ結線です。 青色のワイヤーは、GNDシールドとして使っています。 (グーグル翻訳でごめんなさい)
@Michael-of6ju
@Michael-of6ju 2 года назад
Good 👍
@soundmap-Y
@soundmap-Y 2 года назад
Thank you for your nice comment.
Далее
JUJU HAS IT ALL! | Brawl Stars Animation
00:53
Просмотров 2,6 млн
JUJU HAS IT ALL! | Brawl Stars Animation
00:53
Просмотров 2,6 млн