🔥►► Series 8 - about Pipe-Stoves. #Hiking Hut from the reeds of Tatyana @GordeevaHike. We are testing the operation of the Pipe-Stove while it is cold outside −16-20 °C. We check how the new design of heat-sink partitions made of cans works. We measure the heating temperature of various sections of the stove. Fuel - lamp vaseline oil. #Stove is a structure made of drainpipes. At the end of the film, there are the main dimensions of the sections: the diameters and length of the pipes. As well as the dimensions of the body-can of the oil burner. Experiments with #DIY stoves and camping equipment continue! 😊 🪓 🔥► Tatyana's film about this stove in the Reed Hut, here: • 🔥 Ночевка в Избе в −20... 🪓 🔥► Tatyana's film about this stove in the Reed Hut, here: dzen.ru/video/ watch/63c03f16485a3e425f370913
🔥► All videos about the Pipe-Stove: • Печка-труба своими руками
🪓► All our joint hiking trips: • Совместные путешествия...
📖 Content:
00:00 Minute introduction-spoiler for experienced and attentive. 😉
01:05 Side cuts of a tin can - stops and clearance.
01:35 Frontal cuts - clearance for flue gases.
04:28 The partition for the chimney-heat sink is ready.
05:28 Connection of the 1st and 2nd sections.
05:34 Connection of the 2nd and 3rd sections.
05:43 Connection of the 3rd and 4th sections.
05:50 Testing of the stove-pipe begins! 😊
05:55 Tatyana @GordeevaHike's stove-fireplace in the Reed Hut.
06:28 Removal of wood ash and hot coals from the Fireplace Stove.
06:51 Installation of the 5th and 6th pipe sections - a vertical chimney without baffles.
07:32 Insertion of insulation-partition made of foil porous polyethylene.
07:55 Thermal insulation around the chimney.
08:20 Inserting a cardboard wick into a tin can.
08:25 The base of the Stove-pipe for the installation of the burner.
08:36 Pour mineral vaseline oil into the burner jar.
09:06 We set fire to the cardboard wick of the oil burner.
09:27 We connect the base with the burner and the 1st section of the Stove-pipe.
09:46 On the street, smoke comes out of the 6th section - the chimney.
09:57 The air temperature outside is −20 °C.
10:02 In the Hut, the temperature next to the Stove-chimney is +17 °C.
10:11 Reflections of the flame at the bottom of the Chimney.
10:19 The 1st section of the Stove-pipe has heated up above the boiling point of water.
10:28 Now you can climb into a sleeping bag and spend the night comfortably. 😊
10:45 Morning.
10:58 Dismantling the stove-pipe.
11:05 In the jar of an oil burner - only the remains of the ashes of a cardboard wick.
11:49 Breakfast with cooking in the Fireplace.
12:23 Eugene @jekrecluse measures the heating temperature of the sections of the Stove-pipe.
12:29 Fastening-hanging with hooks of a construction from the 1st-4th sections.
12:35 Connection of the 4th and 5th sections of the stove-pipe.
12:43 Installation of an oil burner in the stand-base of the Stove-pipe.
12:56 Ignite the wick of the oil burner.
13:04 Mounting the 1st section of the stove-pipe on a stand with an oil burner.
13:23 Reflections of fire on the tin can of the pallet.
13:47 There is a strong wind outside.
14:06 The outside air temperature is −16 °C.
14:14 Measuring the heating temperature of the stove-pipe sections.
14:25 The hottest 1st section of the stove - the characteristics of the thermometer were not enough, there are more than +300 °C. :-)
14:37 Table of steel glow colors - with Celsius and Fahrenheit scales.
14:42 The temperature of the hottest place is +500-600 °C - the steel turns red.
15:12 Four places for installation of heat sink partitions.
15:29 There are no heat sink partitions above this place - there is only a straight chimney.
15:37 Temperature at the end of the 1st straight section +140 °C.
15:42 Temperature at the end of the 2nd curved section +130 °C.
15:50 Temperature at the end of the 3rd straight section +90 °C.
15:58 Temperature at the end of the 4th curved section +70 °C
16:06 Temperature of the 5th even section near the foil heat insulator +40 °C.
16:36 Extinguish the oil burner with a tin lid.
16:55 Structural details of the stove-pipe.
17:18 A 500 ml can is the basis of an oil burner.
17:38 The stove-chimney has been dismantled into separate sections.
17:40 Length of straight sections - 100 cm and 50 cm.
18:01 Approximate overall dimensions of the curved sections - 20 cm.
18:18 The diameter of the pipe sections at both ends is approximately 10 cm.
18:37 Tempering colors in the hottest part of the 1st section after cooling.
18:44 The length of the support-stand for the oil burner is 13 cm.
18:52 The height of the oil burner can is 8 cm.
18:59 The diameter of the oil burner jar is 8 cm.
19:08 The ratio of the sizes of the stand-base and the oil burner in different positions.
19:39 Reminder to like. 😊
19:55 End of the movie.
19 июн 2024