10 Day House Build: Day 2 - Framing Walls, OSB and Floor System

Подписаться 370 тыс.

Просмотров 165 тыс.

50% 1

Want to see a house built in 10 working days? Subscribe and follow along to see if our crew can do it!
---
ALL Business Inquiries:
MattBangsWoodManagement@gmail.com
Buy Merch : www.mattbangsm...
Follow MBW : / mattbangswood
Subscribe : / mattbangswood
______________________________________________________
Want to Support Our Channel?
Shop our Amazon Store-Front, we get commission:
www.amazon.com...
Or you can send me something from my Wish List here:
www.amazon.com...
Want to donate directly to the channel instead? Donate here:
paypal.me/matt...
All donations and commission go right back into the content, with giveaways, events, travel costs, etc. Thank you for supporting MattBangsWood and everything we're about.

Опубликовано:

24 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 193

@MattBangsWood 5 лет назад

How are we doing for 2 days in with 4 of us? I'd say we're doing alright. Subscribe if you're not already! Let's hit 20K today! For those that wanted to know lifespan of a Diablo Router Bit.. That bit did all of Season 1 & 2's windows, and it's still sharp doing the windows here.

@alexmitilica99 5 лет назад

They dont give u a hard time for not using galvanized nails in browntone lumber. The inspectors are always on our ass about that

@kyawwinoo1099 5 лет назад

I love to learn it from you.

@teddyvarano3637 4 года назад

MattBangsWood save a good amount of studs if you use off cuts from plates or something for you”channels” and replace that full stud in the middle with 3-1ft ish blocks instead. We call our channels stud black studs. Use then on every corner too instead of California corners. Personally i like stud block studs better, leaves u room to shove insulation in if needed and can be easier for the electricians in some cases.

@mainegeek0 5 лет назад

I am turning 40 soon and contemplating a career change. I have always enjoyed carpentry and framing seems like it would be up my alley. Thanks for the videos. You are never too old to do what makes you happy.

@seapowder3434 7 месяцев назад

Did you ever make the switch ?

@mainegeek0 7 месяцев назад

@@seapowder3434no not to construction but I left a toxic job for one that I am much happier with.

@DailyMobbin 5 лет назад

Framing is just too much fun!! Great video Matt!👷‍♂️🔨

@pcranebmw 5 лет назад

I have always had good luck with a pilot panel bit chucked up for cutting out door and window openings. No bearing to fool with. Bang On.

@cencoast_7.340 5 лет назад

Don’t really have to mess with the bearing, set it once and you’re good. To each his own I suppose

@brayan9274 5 лет назад

Make these videos longer I could watch these all day!

@joshsmith2591 5 лет назад

I've never heard them referred to as channels. Always called them to pars. My first boss would lay out a wall like: x[par]x and the guy making headers would make them up. Keep slaying!

@Bloodgt3 4 года назад

From ohio we call them u corner

@johnpiegzik298 5 лет назад

Great video! Hey I know how you love your Vans, you should reach out to them and help design a framers shoe! Maybe a mid or high top perhaps a steal toe! LOL! You never know! A MATT BANGS WOOD SPECIAL EDITION!! John 👍😎

@FritsvanDoorn 5 лет назад

Oh yeah! Great camera work! Thank you the fun!

@psidvicious 5 лет назад

We used to call the channels, “Ts”. We made them with the cut-offs from the door jacks instead of a full stud. Pencil in the saw guard...naughty, naughty 😆! A case of, “Do as I say, not as I do?” 🤜🤛

@MattBangsWood 5 лет назад

Definitely a do as I say, not as I do kind of person! 😂 I can’t cut blocking the way I do if the guards down.

@nutoriousclown4107 5 лет назад

psidvicious we would just call the Ls

@JustAnotherChippy 5 лет назад

I love your videos for rawness and knowledge. No mucking around with camera tricks or sponsor/not sponsor/click here and there/notification blah blah blah. Keep the puft puft puft sound of gun ringing. 🇳🇿🤙

@MattBangsWood 5 лет назад

I have companies I work with, but I rarely ever do sponsored post. Just showing the real life work day!

@T.E.P. 5 лет назад

super exciting to see this coming together! gotta get some merch to represent here in MN

@kevinobrien1933 5 лет назад

Just a suggestion from another framer put your drywall backer in along the parallel walls before rim makes a great nailer for the rim joist

@rogerkim5652 4 года назад

good to see you switched up the start/stop location when routing windows. was surprised to see you start and finish at the bottoms in previous vids.

@waydemiller8706 5 лет назад

Josh Morrisson said its 2mm out do it again josh is from Australia he’s the best carpenter in the world

@aricv1295 5 лет назад

Nice confidence walking those 2x4 wall plates! Haha I still struggle with those. Especially on 2nd story houses..knees weak!! Nice vid

@jbll36 5 лет назад

Hello Matt. Going up fast!! Hope you didn't have to lug to much material from the back. Can't wait for the next installment. Enjoy the day. Ray L

@linnsoltwedel 5 лет назад

I like to make stuff with a saw and nails, but GOSH you guys are FAST! :D

@teh60 5 лет назад

Very cool, really like this series.

@johngee4688 5 лет назад

You guys Are killing it 🤘🏼

@jodyrolandconstruction6577 5 лет назад

Great work Matt!!🤘🏻🤘🏻🤘🏻

@leonhammond602 5 лет назад

Quality work as usual, break neck speed.👍👍👍

@zacheiriksson 5 лет назад

Instead of using a full length stud for your channel use 3 roughly 12 inch cut offs. Saves material and you use up scraps.

@charlieqian8076 3 года назад

Awesome videos!! How could you guys climb up and down and not feel dizzy or fall from that high.. do you have any protections?

@askaldesign 5 лет назад

good job bro👌👌👌

@edgarguzman5556 4 года назад

Aye matt i have the same problem with a loud compressor just throw a sheet. Over it helps. Alot

@lorenrickey5481 5 лет назад

We can’t tint that dark. 👮 carry tint analyzers now. Build a sound box for that generator out of scrap osb and sheet insulation.

@TheProCut17 5 лет назад

router for the window opening, nice trick. Thanks for sharing.

@MmmmGoodBoy 5 лет назад

TheProCut works great for your username too.

@cencoast_7.340 5 лет назад

I don’t get it..

@dancar1660 5 лет назад

Been Doing it for years !

@KoiAquaponics 5 лет назад

You do good work I wished you were in southern California and allow me to tag along to learn

@MattBangsWood 5 лет назад

Where ya at? I have a frame in LA area that we might be doing. Monster!

@KoiAquaponics 5 лет назад

@@MattBangsWood Orange county, very close by

@Raul-qu4qr 5 лет назад

Same, but I live far away

@cencoast_7.340 5 лет назад

I do framing in Orange County, come hang out I show you what’s up

@stanleysiewierski 5 лет назад

Makes sense to router window openings like drywall.

@lorenrickey5481 5 лет назад

Hey Matt, did that router bit have a bearing on it? Next time try the Diablo 1/2” shank panel pilot bit. No bearing needed and it has a sharp piercing point for plunge cuts. Most lumber yards carry this bit or a generic version of it.

@MattBangsWood 5 лет назад

Hey! I think you've mentioned that bit before, and I really want to try it. I wouldn't have to claw a hole to start either, which would be really really nice! My local yards don't carry them, I'll probably have to buy them on Amazon! The bit i'm using is a Flush Trim Bit - with a bearing. A few months ago I had a bearing fly off, scary stuff!

@Mikeanddrea 5 лет назад

Shouldn’t the second story floor joists sit right on top of the wall studs?

@duckhuntindudewelter219 5 лет назад

What's the reason your long haired buddy keeps his hammer in his bags like that? That would drive me nuts! Anyway keep hangin and bangin brother!

@AntonioRamirez-xg5ce 5 лет назад

Hey @MattBangsWood huge fan of the channel. What hammer are you using? Looks really slick

@latebarz 5 лет назад

Who the hell dislikes a video showing you how things are built!? I can’t understand it! The hate for no reason type! Jeez! 🤦🏽‍♂️

@MattBangsWood 5 лет назад

People that think they can build it better.

@latebarz 5 лет назад

MattBangsWood haha! But seriously... lol

@dancar1660 5 лет назад

Democrats

@billroks313 5 лет назад

Thankyou very much appreciated for sharing the knowledge to the world.Awesome

@tobslobe 2 года назад

It's like watching myself work...pov is Kool. makes 8' look way smaller. i prefer to sheet walls laying sheets horizontal if its possible but i know some places or builds don't allow that. I don't have a cordless/ router so i like to cut my windows out as i go cause ppl cant cut good with the Sawzall or they bevel the plywood so windows flanges cant touch the wall. routers are nice though if you sheet it on the ground or have a lift with a man basket so fast.

@henryperez18 5 лет назад

Nice work

@jeremyford.1499 5 лет назад

You earned a new subscriber! You’re talented bro. I can’t wait to be running my own crew here soon. Probably another year, I’m almost a year in. How long have you been framing?

@MattBangsWood 5 лет назад

Started as a laborer at 15! Just turned 23.

@mehardies3999 3 года назад

Hey Matt. Love your videos. What material did you use on the rim for the 2nd floor? Was it 3/4 in ply ripped to size? Thanks.

@tonytslawncareoffloridal.l8959 3 года назад

I really wish you can come to outskirts Tallahassee to frame my future house up...,🤔

@KoiAquaponics 5 лет назад

Imagine if owner builders took the time to put construction adhesive between the studs and plate priors to toe nails. It would be so much stronger.

@MattBangsWood 5 лет назад

Would definitely make a crazy bond. Would it be worth it though?

@KoiAquaponics 5 лет назад

Only for the home owner/builder. For contractors, it's not worth it because 2 toe nails already meet requirement .

@cencoast_7.340 5 лет назад

Nails hold plenty well, what would be the benefit?

@elnitas 4 года назад

Hey Matt, how do you seal the joint connection between the concrete slab and the sill plate of walls?

@diamondfateful 3 года назад

Amazing!

@mickquaid7709 5 лет назад

In Australia we have to put house wrap on all our frames do you also have to do this aswell as the osb

@TT-ik3kd 5 лет назад

I get how blocking the wall like that before it’s installed makes it quicker and sturdier, but doesn’t it lower the r value significantly in that area because now they cannot insulate behind that. Thx

@MattBangsWood 5 лет назад

Not sure - I doubt it, have to think.. Studs are the same thing, but 92-1/4” tall, they insulate above and below. It calls out for a 4’ block line on plans, but we have our ways of blocking that we stick to.

@elcocotumayor 3 года назад

Great guys god bless you brothers

@jeremyseiler1559 5 лет назад

come to florida and frame we'll show you what the toughest building codes in the country are! hold downs lmao we are all about uplift here bro

@MattBangsWood 5 лет назад

California and Florida, two hardest places to get a General Contractors license and two worst places to build due to spec’d out hardware to codes.. Nobody here is bragging about hold downs, or anything like that.. Just documenting work days buddy.

@michaelalonzo3027 4 года назад

Love your channel. Quick question though. Have you ever made a mistake? whether it was big or small.

@kodakbrown4461 4 года назад

Has anybody else nailed themselves while working?

@ethielurrea 8 месяцев назад

Hey there Matt, great job 👏🏻 Got a question: what is the recommended distance between those I beams and can they be replaced by 2X12’s?

@feaonau7073 5 лет назад

Nice bro.

@kylecorrow702 5 лет назад

How did you get into this line of work? Rarely see young framers or young plumbers or anything. Nice work bro. From Las Vegas

@MattBangsWood 5 лет назад

I'm working on a video on how to get into framing or carpentry at all for that matter.. I feel it needs to be talked about! It's super simple, most people just don't have a clue on how!

@abenzuoo 5 лет назад

your team is FAST :]

@MattBangsWood 5 лет назад

We move right along! Hoping to double speed and have the place done in 5 days, with a day of pick up.. We’ll see.. Today’s not going so well!

@danielchapin8277 4 года назад

That tint will give you a ticket or more

@dylanmounsey7515 5 лет назад

I’d say you’re crushing it

@lorindastephens7580 2 года назад

With the type of flooring used 1 1/2 ply wood then another 1 1/2 how can it be ok to hang a ceiling rack or two in the garage. I’m used to seeing the floors built by a full 2 x 6 or 8. The ceiling racks I’m inquiring about can hold up to 6 hundred pounds.

@ivtec845 5 лет назад

Build a quiet box for your generator check out landberg tiles video on the one he made out of go board

@nitro1380 5 лет назад

Why do block in between studs, is that code in California or spec in the plans?

@spyderx92 5 лет назад

Matt. I see you used the replica hitachi gun ... is good ? Or would you just buy the a5 ?

@MattBangsWood 5 лет назад

I’d buy it over the NR83A5.

@spyderx92 5 лет назад

Kool.. thanks 🤙

@spyderx92 5 лет назад

what is the second tank for? never seen that set up and love to learn new thing . thanks

@GodzUnit01 5 лет назад

what’s the difference between a shear wall vs a regular wall? are there noticeable differences when looking at them?

@MattBangsWood 5 лет назад

Shear walls will have specified shear nailing (6/12, 4/12, MUST use 10d’s) along with spec’d out sheathing. Shear walls will have hold downs at both ends. Technically, non shear sections don’t need OSB at all. Some framers do it that way.. We don’t. We sheet everything! I’ll explain more in my structural plan reading video!

@themalcolmking 3 года назад

Dope video. How do you know where to route out for the windows once you get the OSB up?

@lorenrickey5481 5 лет назад

Just curious Matt, you have cordless drills and saws. What do you use a generator for?

@MattBangsWood 5 лет назад

We have a gas compressor too. Generator is used because 2/7 of us have corded Skilsaws now. I'm working on getting them hooked up with cordless!

@joespha.dubecksr.6083 4 года назад

GRATE JOB WOW,,,

@dougchristopher2072 5 лет назад

New sub here. Bang on Matt 😀

@MattBangsWood 5 лет назад

Hey Doug! Welcome to the channel. 😊

@gacusdt 4 года назад

Just curious why you guys not sheet walls on floor ?

@perrosymasperros8516 5 лет назад

saludos al mexicano.,.,gretings from argentina.,.,brooh god job congratulations .,.,

@ZackAlawi 4 года назад

Why arw the blocks between the studs staggered but in the winery build it was a straight row?

@MattBangsWood 4 года назад

The blocks in this build were just to keeps things rigid, while the walls in winery build have blocking in it for siding backing.

@jbparrothead8532 5 лет назад

Good to see the fire blocking going into the frame...was told by a builder here that it is no longer code...another stupid Cali BS decision.

@MattBangsWood 5 лет назад

Anything over 10’, we block all walls no matter what though! Our preferred way of doing it.

@jbparrothead8532 5 лет назад

MattBangsWood Best way to do it no matter what... sign of a conscientious builder...

@atamagashock 5 лет назад

Quietest Ramset I ever heard

@MattBangsWood 5 лет назад

Hilti DX36M - Paid $35 from someone at a Yard Sale for two of them, like-new in box!

@philb9550 6 месяцев назад

What was the pump action nail gun into the bottom plate?

@zacheagle3018 5 лет назад

What your calling a channel we call a tee post in NC . It’s funny but a corner or tee post built with blocks in the middle we call a California corner or tee.

@MattBangsWood 5 лет назад

Isn’t it funny how things change, place to place? Lol I’ve always tripped out on that!

@cobylocke3249 2 года назад

What Vaughan hammer do you use ?

@mechanicosz9337 2 года назад

Why everyone is using OSB for sheathing instead of fibreglass gypsum boards, like the GP Dense Glass or USG Securock, or Glasroc X?

@johnmeoff Год назад

im confused is hiis the first floor over a basement

@wesleylindley1229 3 года назад

What’s the nail gun you run ?

@LucasHenrique-ll7nt 4 года назад

That's something cool! Can you share de floor plans? I'm a civil engineer from Brazil and we do not build wood frame here! Cheers

@beverlyHillsAgent 2 года назад

in 9:51, how did the nail get in? diagonally?

@flyby8049 5 лет назад

You guys work fast 👍 what router bit do you use to cut out windows?

@lorenrickey5481 5 лет назад

FlyBy804 take a look at Whiteside pilot point router bits

@flyby8049 5 лет назад

Loren Rickey thank u

@farofalo 4 года назад

If you frame exterior channels like that, how can you get your insulation in?

@tracycolorado 5 лет назад

put the generator in that garage to keep the noise down

@MattBangsWood 5 лет назад

We have to go in there. It’ll be a death room if anyone goes in there! Lol

@MattBangsWood 5 лет назад

Right now - it’s actually REALLY close to the bathroom.. and it fills the bathroom up with exhaust fumes! Fun stuff! 😂

@nutoriousclown4107 5 лет назад

Stiletto Tibone vs martinez hammer ?

@MattBangsWood 5 лет назад

Dalluge 16oz!

@nutoriousclown4107 5 лет назад

Btw man how did you get used to walking top plates 🚶 I’m only able to do it on 2x6 external walls. Any tips?

@MattBangsWood 5 лет назад

Takes time, I was scared to when I was younger, after a while of getting comfortable, you know it's just part of the job.

@MattBangsWood 5 лет назад

Tomorrow is a fun one. All second story top plate baby! WOO!

@redrhino1911 2 года назад

Damn all us younger framers really use the same lingo lol.

@frankuzmic4305 8 месяцев назад

Hi, greetings from Croatia, what is name of these at 10:41?

@spencerjohnson1052 3 года назад

How do you chose to use these i-joist vs a straight 2x10 for the floor joist?

@Bloodgt3 4 года назад

We call thoes channels, u corner in ohio, but mostly we just put blocking in between the stud space every 2 feet. Our builder doesn't like the the air space that is left with the u corners.

@mars6433 3 года назад

@0:37 bet that tint is way too dark for California vehicle code.

@meandnature6452 5 лет назад

do your crew work on weekends?

@MattBangsWood 5 лет назад

Nope, we’re trying to do (4) 10’s - with 3 day weekends.. but we’re still working Fridays.

@meandnature6452 5 лет назад

@@MattBangsWood we do 8hours 5 days but i would rather do 10hrs 4 days

@carstengrove6214 5 лет назад

What gun is that your using

@MattBangsWood 5 лет назад

PneuTools Framing Nailer! can find them on Amazon.

@josecorona102 7 месяцев назад

Hermano un libro de framing que me recomiendes

@mitchell9153 5 лет назад

Why not 2x6 as backer instead of 2 2x4s

@MattBangsWood 5 лет назад

7” vs. 5-1/2”. A 2x6” over a 2x4” wall only gives an inch of backing on both sides. The way we did it allows for 1-1/2” on both sides.

@aweaweaweaweawewa8317 5 лет назад

is your airhose polyurethane? what brand is it?

@MattBangsWood 5 лет назад

Yes it is! 😊 We run Husky (Home Depot) or Hitachi Hose, 1/4” for going to guns, 3/8” Flexzilla hose to go from compressor to tank.

@lorenrickey5481 5 лет назад

MattBangsWood Flexzilla is great especially in cold weather. Lays flat no trip hazards. Bostich makes a good hose too. Check out Home Depot’s Dewalt hoses during Christmas for a good deal @ $20 for a 1/4 x50 with connectors.

@bearshield98 5 лет назад

New subscriber, like ur channel, I'm not a professional carpenter, but I've learnt a thing or 2 watching ur videos... just a tool question, ur router bit u use on ur windows, how many do u go thru on a typical job?

@MattBangsWood 5 лет назад

That router in the video has now done 2 or 3 full houses! 😊