No video :(

12v Anderson Plugs and Connectors - FLOOD SOLDER

Подписаться 33 тыс.

Просмотров 19 тыс.

50% 1

In this video I show you How To Flood Solder an Anderson Plug Electrical Power Connector. Anderson plugs are a solid and simple electrical connector that give you a solid connection for your outdoor electrical connection needs. Check this video out for a run down on how to make up a wire with Anderson plug connectors using the floor solder method :)
► Buy Anderson Plugs: amzn.to/2R8PKHL
The second version of how to install Anderson plugs onto wire using a hydraulic crimping tool is out now on the channel - head over the 'Electrical' playlist on the check it out or click here: • 12v Anderson Plugs and...
► Enjoyed? Buy me a beer 🍺😀 bit.ly/videosho...
► Don't forget to SUBSCRIBE and hit the bell for UPDATES :)
Be sure to leave a comment in the comments section, share with anyone you think might find this useful, subscribe for more video's just like this one!
For business enquiries email - videoshowmehow@gmail.com
***************************
A bit about VideoShowMeHow
***************************
►Where did this start?
I really enjoy tinkering with different projects - they usually require a whole bunch of research and learning along the way. It's satisfying on doing a thing and standing back and going 'Yeah! Totally did that!'. I had a bunch of mates asking 'how did you know how to do that?' and 'I couldn't never do that myself' so I thought; I need to start something where I can help others that might be thinking the same thing :)
►What will you find here?
The purpose is simply to make these videos as top quality and helpful as I can. They will always be free, there's ZERO agenda and the only motive is to try and upload what I would want to watch to help with that particular project. I'm also keen to keep building this little community and will try to answer all questions when asked - fire away :)
New videos are being uploaded regularly so if there's something you'd like to see, have Questions and/or Comments drop me a line.
Cheers guys.
Adam
***************************
#videoshowmehow #andersonplug #solder
Disclaimer:
If you click any of the product links above and end up purchasing anything I get paid a small commission (not charged to you). This is one of the ways you can support the channel :)
VideoShowMeHow assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from the information contained in this video is the sole responsibility of the user and not VideoShowMeHow. VideoShowMeHow cannot guarantee against improper use or unauthorised modifications of this information.

Опубликовано:

23 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 10

@VideoShowMeHow 3 года назад

CHECK-OUT ALL THE 12v VIDEOS HERE 😃 -> ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2BikJusnD9Y.html

@twagner6155 4 года назад

Though your solder job held I put solder flux on the wire and in the connection too.

@VideoShowMeHow 4 года назад

Nice, thanks for the tip

@sreekumarUSA 3 года назад

101020/1438h pst. I’m here once again, to sincerely apologize for expressing my affinity towards soldering Anderson connector or any high current connectors (ring terminals etc) I retract that statement and wholeheartedly support crimping the contacts with 10 Ton hydraulic crimper. The soldering to Anderson connector became a mess and looked hideous. Fortunately I have the 10 Ton hydraulic crimper. The final product looked very professional neat and tidy. Thank you , stay safe and 73s...

@sreekumarUSA 3 года назад

093020/1311h pst. Thanks for the 2nd segment of connecting cable to Anderson connector, by flood soldering. I, always prefer to solder smaller cables, (up to AWG10) to ring connectors and to connectors of similar types as above.This is due to “Wing” formation and the struggle to trim and fashion the area. The larger AWGs, it’s best to use the Hydraulic press/crimper as you spoke and demonstrated in the previous video. In the first part of the video, after filling the cavity with Pb, it looked that the Cu strands were simply dipped into the molten Pb. Under such conditions Pb may not adhere to Cu properly thus giving rise to an undesirable “dry solder” condition. It’d have been proper, to either pre-tin the Cu strands or dip the Cu strands in KESTER #921 fluid flux before insertion into molten Pb. I faintly, observed in the second part of the procedure, that Cu strands were Pre-tinned before insertion. ThT was nice. Like you mentioned, the Ronson torch was an “overkill” (excessive heat) and in the process, the Ag got oxidized. But the theory is well taken. The above comments are only an observation nothing but that. Your project is well appreciated and respected. Thank you, Sir. Stay safe and 73s...

@rosswines 10 месяцев назад

Hydraulic crimper always better. Eliminates risk of a dry solder joint.. you may think you have a structural join but not necessarily a good electrical join - my personal experience of 50 years doing amateur electronics and Amateur Radio!!! When soldering with blow torch - connector can get too hot causing oxidization of the silver coating of the Anderson connector affecting electrical join. Both the Anderson connector and the wire cable need to be fluxed / tinned with a temperature controlled soldering iron before soldering to join electrically both parts. if insufficient contact join area and you try to pass high current through it - that could cause heating of the connection and even failure of it. So message is - crimp it!! That is why profession installer always crimp. End of story!!

@michaeldoherty2289 3 года назад

Nice discussion and show and tell. My only comment is I think you contaminated your solder joint with melted plastic insulation which could compromise the strength and electrical conductivity of the joint. Trim off a little more insulation so you don't do that would be preferable to me.

@moikehunt8928 Год назад

Should the ends of the cables be tinned before inserting them into the well?

@VideoShowMeHow Год назад

Not necessarily no

@twagner6155 4 года назад

I think you didn't mention about the type of solder you used. It is very important to use some sort of flux, I think you have flux core solder. Also the cheesy jumper cable clamp isn't strong enough for me, I used vise grips. Check out T Wagner's video.