13 Ways To SECURE Flat Surfaces To Conduit!

Подписаться 21 тыс.

Просмотров 13 тыс.

50% 1

Over the years we have seen a lot of creative solutions for securing flat surfaces to conduit builds and frames. In today's video, we look at 13 of these solutions and learn how they work. Check out the links below for more information about the builds and other resources we discussed in the video. Thanks for watching and be sure to subscribe for more weekly videos and build inspiration!
------------ Product Links -------------------
EMT Conduit One Hole Straps - makerpipe.com/collections/mod...
EMT Conduit Two Hole Straps - www.lowes.com/pd/Sigma-Electr...
Maker Pipe Flange - makerpipe.com/collections/mod...
Maker Pipe Puzzle Piece Clamp - makerpipe.com/collections/mod...
PVC Pipe Clamp - www.amazon.com/uxcell-Clamps-...
Spring Clips - makerpipe.com/collections/mod...
Conduit Hanger Straps - www.homedepot.com/p/Halex-1-A...
Threaded Pipe Inserts - makerpipe.com/collections/mod...
--------------------------------------------------------
----------- Community Builds ------------
Lush Storefront Shelf - connect.makerpipe.com/post/ou...
Adjustable Shelves - connect.makerpipe.com/post/ch...
Quick Access Panels - connect.makerpipe.com/post/lu...
Ikea Desk - connect.makerpipe.com/post/he...
Electrician's Table - connect.makerpipe.com/post/ht...
Six Monitor Desk - connect.makerpipe.com/post/an...
Laser Shop Storage Shelf - connect.makerpipe.com/post/ok...
Liquor Shelf - connect.makerpipe.com/post/my...
Aquaponics Flood Table - connect.makerpipe.com/post/us...
Enclosure Roof - connect.makerpipe.com/post/fi...
------------------------------------------------------
----------------Videos-------------------------
Saunders Build Out - • We Built Custom Packag...
Tube Insert Overview - • Mount Anything To Cond...
EMT Conduit Flipped Over - • Why Didn’t We Think Of...
Adjustable Angle Overview - • Perhaps The Most Versa...
Simple Pipe Desk Build - • Build Your Own DIY Pip...
Ping Pong Table Restoration - • I Can't Believe They W...
How To Make EMT Conduit Flanges - • How To Make A Flange F...
Adjustable Angle Coffee Table Build - • RAW Coffee Table Build...
Upside Down One Hole Strap Strength Test -
Grip Clip Uses - • These Little Clips Are...
Frost Proofing The RV - • E12 - Frost-proofing t...
------------------------------------------------------
Community Kits - makerpipe.com/pages/community...
Contact Us - makerpipe.com/pages/contact
Need Some Inspiration? Download Our Free Build E-book - makerpipe.com/pages/be-insipi...
Follow Us On Social
Facebook - / makerpipe
Instagram - / makerpipe
TikTok - / makerpipe
Join Our Free DIY Community - connect.makerpipe.com

Хобби

Опубликовано:

5 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@MakerPipe Год назад

While editing this I realized there's a couple of things that I forgot to include in this video that I think are worth mentioning. 1. The rule about getting a bolt or screw that secures the material without going completely through it applies to pretty much all of the methods. 2. When I talked about pipes interfering with a flat surface I failed to mention that in those builds you should support the material with the longest pipes in the build. Basically if your shelf for example is really narrow but deep then you will want the side pipes supporting the material. If your shelf is really wide but not that deep then you should use the front and back pipes to support the flat surface. If you have any questions about anything, please put them in the comments or reach out to us. Thanks!

@TinyDantz Год назад

But don't the shelves basically rest, not on the pipes, but on the connectors themselves at the corners? That is, unless the shelves bend. The connectors are 1/8th thicker than the pipe so the shelves sit on them at the corners, not the pipes directly. I've been thinking of adding connectors in the middle of the 3-foot wide shelf unit I'm starting to build so that it doesn't droop in the middle even this 1/8th of an inch. Am I wrong, or too worried about 1/8 of an inch?

@TinyDantz Год назад

Great Video. I've been hoping for a round-up on this subject!

@christiancicirale7149 Год назад

@@TinyDantz I was thinking about this as well. Some type of connector or bushing mid span would prevent any drooping.

@raymondhill3 11 месяцев назад

Thanks, this video has the answer to my work challenge!!!!!!!

@MakerPipe 11 месяцев назад

Awesome! Glad you found it useful!

@zombalia Год назад

Just discovered Maker Pipe here on RU-vid and I am STOKED! What an awesome product you guys have created. I cannot wait to get creative and start building. And truly, your videos are delightfully done. Thank you!

@MakerPipe Год назад

We're stoked that you found us too! Thanks for the comment and good luck with your builds!

@michaelbowie4358 Год назад

I made an open shelf unit for my brother and used the threaded pipe inserts on both sides of the shelf and linked them together with a length of all thread. Since the hole I drilled just allowed the all thread to go through I could screw the conduit tight to the shelf.

@MakerPipe Год назад

That’s awesome! We’ve seen that done a couple of times and it’s always really cool. We’d love to see yours too if you feel like sharing the build. Thanks for the comment!

@MakerPipe Год назад

Oh wait I just realized what you meant! That’s a super clever thing to do!

@carmenmarcinkiewicz7149 Год назад

I love your video edits......so entertaining!

@MakerPipe Год назад

Thanks Carmen! That means a lot!

@05BaNsHeE27 2 месяца назад

Can you show or give me any ideas for how to make a custom oval shower rail to go over a freestanding tub? I was going to use 3/4 emt and was trying to figure out a T for connect to wall and ceiling.

@MakerPipe 2 месяца назад

That sounds interesting! Have you seen the flanges that we make for EMT Conduit? Standard Flange - makerpipe.com/collections/modular-pipe-fittings/products/flange-connector Adjustable Flange - makerpipe.com/collections/modular-pipe-fittings/products/adjustable-angle-flange

@Thomas-qk7wf Год назад

Any chance you have more information or a source for the table pictured at the 6:45 mark? There's a lot of bracing in that structure and it might work for a bed frame I'm working on for our van. Or give me a few ideas on how to approach it.

@MakerPipe Год назад

Hi there Thomas, thanks for the comment. We built that when we launched the adjustable angle connector. We did a timelapse of the build that you can watch here -------> ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-eV7FjXug2iA.html Let me know if you have any questions.