14 Bolt Disc brake conversion part 1 

Glad you found the videos helpful, thanks for watching

Glad you liked it and thanks for watching!

thanks for the tip and thanks for watching

Glad you liked them. Thanks for watching. More videos coming soon

Check out www.sneveysoffroad.com/ they have a 14 bolt 6 lug hub conversion kit.

Thanks for watching!

Glad you liked the video. The rotor I got in the kit is a 12.4 in rotor. part number 5523. Thanks for watching

My axle is a full float 14 bolt. Check out this link to help identify which axle you have. lugnut4x4.com/axles/14-bolt-axle-identification/ Also use this link for tons of good information about the 14 bolt www.billavista.com/tech/Articles/14-Bolt_Bible/index.html Thanks for watching and good luck on your project

Yes, my stock 16 inch rims fit with no issues. My rims are steel. I assume they are stock, they are cheap looking steel rims, but yes they fit with no issues. Now they are tight! But no rubbing that I have noticed. Thanks for watching

Did u end up doing it I have a 99dually

I think my WMS width stayed the same. If it did change it was minimal. Per lugnut4x4 website any changes should be less than 1/4 inch. Thanks for watching

awesome thank you. cheers @@Offroadfarm1

I used plenty of pb blaster but I don't have an offset flare wrench

The process will be similar. lugnut4x4 has a kit for the newer style of 14 bolts with slide on drums. If you opt for the slide on rotor then you won't have to press or knock out your studs. He also has a kit that will go behind the hub and you will have to knock those studs out. My truck is a '88. Thanks for watching!

@@Offroadfarm1 i still don't understand what rotors i need to get, the slide on rotors for stock vehicles or rotors behind the hub. mines a 1996 k3500 with slide on drums i don't have to remove hub to get drum off

You can get either. Keep in mind regardless of which style rotor you get you will still have to pull the axle and remove the hub so that you can remove the dust shield/backing plate and then install your new caliper mounting bracket. Slide on rotors : remount the hub, slide on rotor, install caliper, mount wheel, done(don't forget to hook up and bleed your brake system) Rotor behind the hub: Press or drive out all 8 lug studs on both hubs, put rotor behind hub, press or drive in all 8 lug studs per hub through rotor into hub , remount hub, install caliper, mount wheel, done (hook up and bleed brake system) The slide on rotors are easier to install but cost more. If you have access to a press and want to save some money then you can get the behind the hub rotors. They will save you some money but will take a little longer to install. (If you don't have a press you can still install the behind the hub rotors to save some money. You will have to knock the lug studs out with a air hammer or a BFH, it will take longer and be more work but it's totally doable.) Also make sure your running at least 16 inch wheels to clear those new calipers! Hope this helps Let me know if you have any more questions Thanks for watching

The kit I used was for SRW but I believe lugnut4x4 also has a kit for DRW. Thanks for watching

No I don't. Check out this webpage. www.billavista.com/tech/Articles/14-Bolt_Bible/index.html It has tons of info on the 14 bolt. About half way down he talks about the difference between SRW and DRW. I believe you can simply change the hubs to SRW hubs, but I have never done it before so I am not certain. Thanks for watching and good luck on your project!

@@Offroadfarm1 The detail and part numbers and links sums it up. Thanks and Thanks again from all the people I will pass what you told me along and where to find it.

Measure from the center of your rear chunk to the axle mounting surface. This will give you a rough idea of how long your axle shafts are and how much room you will need to pull them. Once you get close to the end you will be able to angle the shaft some. A quick search looks like your shafts should be around 32 inches long. I would say you would need at least 30 inches of room, maybe 32. Good luck on your project and thanks for watching!

@@Offroadfarm1 thanks for the info, I've been watching your videos on this subject several times, I'll be starting on the conversion this weekend and through the 4th of July and hopefully have good luck, thanks for making very informative videos👍

I don't have drum brake tools and they were easily removed with a long screwdriver. Also I had no plans to reuse anything, it all when in the scrap bin. Thanks for watching

Could have just left it all together and just pulled the 4 backing plate bolts and removed it all as one assembly.

Feel free to email me offroadfarmchris@gmail.com and I'll do my best to answer your question, Thanks for watching

My kit was roughly $600. That did include the E-brake calipers and new bearing which added close to $300. Their basic kit for a 14 bolt starts at $315 but shipping to Canada per their site is $150 which is high. You may be able to find a company in Canada that offers a similar kit and save on the shipping. TMR customs does offer a kit which includes the bracket, rotors, calipers, and pads for $429 CAD no idea about their shipping charges. Good luck and thanks for watching

I don't think I still have them. They went in the scrap bin and we hauled it off a few months ago. I will try to check this weekend. If I still have them, they are yours if you'll cover the cost shipping. Thanks for watching

I checked and I no longer have them.

Are you asking about the flange bolts? Mine were not a problem to get loose as you mentioned. They should only be torqued to 115 ft-lbs. Maybe some one used locktite on them? Have you tried heating them? Have you tried a cheater?

@@Offroadfarm1 my left hand side axle broke free pretty well but the right one is still hard as a rock. Ill try a cheater tomorrow. My guess is they were over torqued. Thanks for the help

Any luck getting the right side axle loose?

@@Offroadfarm1 yep got if off. Then my wheel cylinder locking nut stripped and it took a hammer, chisel and some beer to get it off lol

Glad to hear you got if off

I have new lines to put on, just haven't done it yet