1911 Barrel Fitting and Bushing Relief

Подписаться 29 тыс.

Просмотров 86 тыс.

50% 1

Check out my book on Amazon!
Insurgency: Refreshing the Tree of Liberty
www.amazon.com/Insurgency-Ref...
Gunsmithing Tools (using these links to buy tools, etc., will help support this channel, but at no additional cost to you. Also, if you browse and purchase other products after clicking on these links, that will still help support this channel.)
Sandpaper-400 to 2000 Assorted Grits, 9 x 11 inch, Dry/Wet | amzn.to/2UVqEuo
1911 LUG FITTING KIT | snp.link/75ad55d1
FRIEDR. DICK GMBH PROFESSIONAL GUNSMITH NEEDLE FILE SET |
HARRISON DESIGN & CONSULTING TRUE RADIUS PRO SEAR JIG | snp.link/5232281d
ED BROWN 1911 SEAR JIG | snp.link/293938b6
NORTON 6" X 1/2" X 1/2" INDIA STONE | snp.link/3cdeb22e
NORTON PREMIUM HARD ARKANSAS STONES | snp.link/5f35d8c6
BROWNELLS 1911 ANODIZED BUSHING WRENCH | snp.link/5218f3d6
Trigger Track Stone : BROWNELLS 1911 TRIGGER TRACK STONE | snp.link/440f2fdc
Barrel Alignment Block : BROWNELLS 1911 BARREL ALIGNMENT BLOCK | snp.link/2557da5c
Slide/Frame Rail File : BROWNELLS 1911 SLIDE/FRAME RAIL FILE | snp.link/054afae6
BROWNELLS 1911 HAMMER SQUARING FILE | snp.link/ff4d99a3
FRIEDR. DICK GMBH NEEDLE FILE HANDLES | snp.link/
Rotary Tool Kit (like Dremel) with MultiPro Keyless Chuck and Flex Shaft | amzn.to/2Dm0U4A
Dremel 684-01 20-Piece Clean & Polish Rotary Tool Accessory Kit | amzn.to/2IuUfJq
TEMO 10 pcs 8mm (5/16 inch) Bullet RUBBER Rotary Tool Polishing Burr | amzn.to/2PskWiJ
Dremel TR470 60, 120, 240 Grit Band | amzn.to/2ULlLZv
JOHN MASEN MASEN BRASS HAMMER & PUNCH SET | snp.link/f2fd6484
GRACE USA ROLL PIN PUNCHES | snp.link/b1899a9b
Nicholson Type B Wooden File Handle, Size 3, 4-1/8" Length | amzn.to/2IQ0PK3
Nicholson Metal Ferruled Wooden File Handle, Size 4, 3-3/4" Length | amzn.to/2Iwnuvt
Woodstock D3111 Rubber File Handle, Rectangular Hole, 5-Piece | amzn.to/2IFCaYk
Nicholson 183-22025NN 22025NN 8 Piece Machinist File Set | amzn.to/2ZjS3tj
Holsters from Amazon (If you browse to other products at Amazon after clicking on these links, that will still help support this channel.)
Holsters (these are some of the holsters in my personal collection)
Fobus Standard Holster RH Paddle 1911 | amzn.to/2P9HHrr
Fobus Standard Holster RH Paddle Glock 20 | amzn.to/2IhKFtf
Fobus Standard Right Hand Holster Glock 17,19,22,23,26, 31,32,33,34,35 Compact Style | amzn.to/2GceurR
Fobus Glock 17/19/22/23/31/32 | amzn.to/2GchvIw
Fobus Compact Holster Paddle 1911 | amzn.to/2IzxDXl
Fobus Concealed Carry Roto Rotating Paddle S&W Shield | amzn.to/2IgTLGA

Опубликовано:

23 фев 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 71

@tonykomer2997 2 года назад

Nice video. A few suggestions. As a general rule slide the barrel bushing over the barrel first then seat the bushing in the slide before allowing the barrel to locking to the bushing. Doing it with the barrel already installed wears that precision .001 slip fit. Stop short next time with the lug cutter. Just before the safety seats into the slide recess. This way as you finish polish the feet it will not advance the slide rearward further creating a gap that frankly may wear in so with use and grow a thou more. A way to check that barrel foot radius after using the cutter is to install the link into the barrel and add the release pin and try to swing it thru its range of motion. It show smoothly ride that foot radius not bind anywhere. That will get you to the minimum. As if the link can not rotate thru it will not cycle and bind instead. Then you can check with it installed on the slide (yes with the bushing installed... we all miss stuff especially trying to film too). Have the foot all dykem coated and clear the high spots. Technically ideally if you had the slide stop pin installed and it was spinning you would feel not bind and the pin would evenly clean the dykem off the radius. That would be a true 0 tolerance fit. Takes serious patience polishing and testing over and over. If you are doing any kind of cerkote or dlc coating do not get it that tight as the combine parts layers can add up to 5 tenths (0.0005) and might bind if you got it that tight. I like every mating surface part to have a high polish in the direction of movement. Keeps everything to the lowest friction for butter smooth cycling, The feet, link pin and pin hole, slide pinnstop shaft. I like my bush to fit snug in the frame where you have to use a bit of force to spin it out. That still is a slip fit but ensures undetectable movement. I prefer the bushing to fit where it just stops binding the barrel. Just were it stops springing. Polishing gets you there at the end that last 5 tenths. If the slide has any vertical play when you are checking that radius link fit you want to pull up on the frame as otherwise it will allow increased tolerance between barrel and slide lugs. Also did not see the hood fitting but be sure to check firing pin centering but do not allow it to be the ultimate spec. A bit off center but perfectly fitted hood and top lugs is the most critical. 9bviously it can not be off significantly but a tiny bit is no big deal.

@Renrondog 5 лет назад

Excellent video, I'll never attempt this process but it gave me valuable insights on exactly how lock up works . Thank you for taking the time to show us.

@ralphmamauag7018 4 года назад

Bring the camera a bit higher in the 1st part of the video

@CB-68-westcreations 7 лет назад

The Lug mill makes sense. The other tools are easily made from either head wood or nylon. Thanks for taking the time to make this video 😁 More people should consider it.

@youngbuck9481 4 года назад

Great information but you gotta either move the camera back or keep the slide in the video!

@bjbstewart 5 лет назад

REALLY well done - appreciate the detail and video quality!

@JohnDoesItAll 4 месяца назад

Wow! Who knew! Thank you for sharing😊

@biggysground 5 лет назад

Jay, much better barrel fit on this vid than the other one you did. Still, you should have the bottom lug fit a little tighter to where it requires a little bit of assistance to gain lock up. 20 + rounds break in before it starts to cycle with no problems. One knot holes at 50 yrds is the goal.

@-NOGOODRACING- 4 года назад

Your hand motion cutting looks very good, the surface after cutting looks like a milling machine cut, very smooth and clean cut!

@fredgreer7481 7 лет назад

Could watch this stuff allll day. Thanks Jay and keep at it!

@jayphilipwilliams 7 лет назад

Thanks! I'm glad you enjoy it!

@LifeReloaded1911 6 лет назад

Love the video!

@s.e.8719 2 года назад

Outstanding video!

@timw9919 5 лет назад

you need the bushing installed to finish the lug fitting. An old or factory one not the one you precision fit. Do you have any of the print manuals? IMO that is a MUST HAVE. ETA: Sorry I jumped the gun I just hated to see you over cut and change the angles on the lugs I posted before watching the rest of the video. I see you already figured that out. I should have finished the video. You are learning and thats good. Next time it would save you some money to start with cheaper gunsmith fit barrels than the top of the line Barsto. Those mistakes can be more costly. Honestly just start with an RIA/Fusion even a Ruger1911 and pay a small fee for a local precision tig welder to weld up the rails so you can fit the slide. You could even have him weld the lug and hood on the stock barrel. Add a match bushing to fit. Build and fit that. Once you have it down then order you Caspian frame and slide (or a Colt 70 GI). Get it with whatever extras you want flat top lines checkering etc. I will say I think its good to hand checker a couple ties just so you understand it and are then able to repair checking better. Honestly even mill checkering is a PITA to setup the jig and you need a good not hobby mill to do it. Hand checking teaches patience and mental endurance attention to detail etc. There is also way more pride when you finish a perfect job. Trust me. You should be applauded for doing this documentary of your progress thru 1911 pistol smithing. Stay with it you are improving very nicely. Just more patience writing numbers down and pausing to think and contemplation of choices before removing more metal. The guys over on 1991forum gunsmith section would be happy to offer and help you with questions and tips especial as you have video to show where you are at. A number of very prominent smiths on there that are willing to still offer knowledge.

@timhallas4275 3 года назад

You made a perfect machined surface, but then you finished with a hand held Dremel tool. I'm pretty sure those surfaces have to be parallel and square to each other.

@abrahamm1325 7 лет назад

excellent video you couldnt ask for a more detailed video

@jayphilipwilliams 7 лет назад

Thanks! I'm really glad you enjoyed it.

@FlyTJ 5 лет назад

What a great video! Maybe I'll see ya at Oshkosh! 😀

@PatriotPaulUSA 3 года назад

Wow 45 thou of lug engagement is a lot from what I have seen. Nice job if its not to tight. Really awesome video for us new guys Thanks. I have seen that the lower feet should have a very small angle up into final lock position just a degree or 2 as well some gunsmiths say. Excellent job explaining the process.

@jayphilipwilliams 3 года назад

I still consider myself a new guy! I agree about the small angle on the lower lugs, so as the barrel gets pushed forward, the upper lugs are engaging more and more. I'm glad you found the video useful!

@abrahamm1325 7 лет назад

during my 1911 build i noticed that when the barrel bushing is not installed the barrel had a hard time getting pushed up into the lugs. its easier to see how they will engage with the slide by holding the frame and slide upside down. this lets gravity pull the barrel into battery.

@jayphilipwilliams 7 лет назад

Yeah. I was thinking I'd measure the lug engagement again, but this time with the bushing installed. :) Might get even more engagement. Thanks for the comments.

@joeybunkerslgl15gbunker25 3 года назад

Good stuff thanx so much for your knowledge bunk auto n small eng

@brianonthego 7 лет назад

Subbed your channel.

@PimptatoPCs 3 года назад

My barrel is getting hung up a little on the front edge of the ejector port while pulling the slide back. There doesn't seem to be consistent downward motion of the barrel when transitioning out of battery. If I keep the firearm perfectly level then it works better, but as soon as I turn the frame to the side at all it hangs up. Just wondering what surfaces need adjusting to make the barrel move downward before the slide comes into contact with the hood. Any advice or pointers would be appreciated.

@jayphilipwilliams 3 года назад

Howdy! I would recommend you go to the gunsmith section of 1911Forum.com. There are some professional gunsmiths there and they're your best bet for help. forums.1911forum.com/

@malnwah726 5 месяцев назад

Camera isn't centered on what is being performed.

@poncoolride 6 лет назад

How much are the tools to do this?

@MarceloPereira-ll4go 3 года назад

Top

@marianai234 4 года назад

I’m having that same problem

@keithreinert5835 5 лет назад

Are you in Wisconsin? I live in Appleton close to eaa. Good vid!

@jayphilipwilliams 5 лет назад

Thanks! Glad you liked it. We live in Tacoma, WA. I was just in Oshkosh for a week, though. :) Flew in and out of Appleton. A buddy of mine from Wisconsin Rapids came for a few days, too.

@trabalhosverticaisbuica1463 7 лет назад

Good afternoon I have a super homelite 2 automatic oiling and when I put it to work begins to pour oil through the exhaust and put a lot of smoke, another one and the oil does not go out, what will it be? I appreciate your help because I do not speak English much THANK YOU

@jayphilipwilliams 7 лет назад

I think that when you get the oil in the exhaust, it's because the tubes are hooked up backwards, so the other way is probably correct. I would just try and make sure the oil passages are not plugged up.

@trabalhosverticaisbuica1463 7 лет назад

Muito obrigando pela ajuda vou ver.

@kevinkyger6558 7 лет назад

Can you give me the name of the jig you mentioned to do this job on a mill?

@jayphilipwilliams 7 лет назад

www.jackweigand.com/EBF1911.html

@FernandoOliveira-cw4mk 6 лет назад

Another doubt. what is the video where you take measurements from the barrel of 1911 cal.45 acp. Obrigado Jay.

@jayphilipwilliams 6 лет назад

I'm not sure what you mean.

@FernandoOliveira-cw4mk 6 лет назад

@dustyharry8402 7 лет назад

At 27:00 you do the lug engagement measuring all wrong, to get the correct reading, you need to put something between the breech face and the hood (about .1" thick), push the slide forward and do the second measuring, and you need to have the bushing installed while doing that

@caminhoneiroporamor.sabino4 5 лет назад

Show.

@ogsniper743 3 года назад

Nice video! Really helped me alot thanks! Did you sell the barrel lockup tool?

@ericbelanger7373 3 года назад

That extra tool you wanted to sell did you got rid of it or you still have it ?

@jayphilipwilliams 3 года назад

Seems I lost it.

@raging_rhino2582 3 года назад

Jay from 4:30-5:30 the work is out of frame my good man (Great job anyway)

@thomasp.monroe4922 6 лет назад

I think Jay you need to learn to use a Dremel properly. You are not keeping the Dremel cratex polishing stone parallel to the 2 lugs you are polishing . Therefore the lugs surfaces will not have full contact with the pin. Also you you should have stopped a little earlier with the lug cutter and finished with a round stone by hand to eliminate the excess clearance in the safety.

@tonyyanezjr7835 6 лет назад

Hi do you still have that tool for sale and how much?

@jayphilipwilliams 6 лет назад

I do. It's $20.99 + shipping on Brownell's, so I would send it to you for $20 even, including shipping. It's still in the original sealed package.

@tonyyanezjr7835 6 лет назад

Jay Philip Williams please send info again it got deleted some how

@blusky7072 4 года назад

Please move the camera out farther from the table. That way we can see what you are explaining. Thanks

@FernandoOliveira-cw4mk 6 лет назад

Hello good evening. I have a doubt, What defines which link barrel I use? Did I test the number 1 through 5? thank you.

@jayphilipwilliams 6 лет назад

See if this post helps: forums.1911forum.com/showthread.php?t=500485

@FernandoOliveira-cw4mk 6 лет назад

OK. I'll search the site. thank you.

@juanvillegas7597 3 года назад

Great information , but the only thing you show is your hands , get a wide angle lens to show your information thanks

$@frackyouasshat5531$

@frackyouasshat5531 7 лет назад

does anybody make a 1911 10 millimeter long slide

@jayphilipwilliams 7 лет назад

At a minimum, Caspian does (the company I'm using here). www.caspianarms.com/product-category/long-6 You might ask on forums.1911forum.com for more options. Someone there will know more.

@alexgman1988 5 лет назад

Springfield armory just released a 10mm longslide a couple months ago

@TheREALLibertyOrDeath 5 лет назад

Iver Johnson eagle-xl

@billrichardson4873 6 лет назад

You need to fire the camera man

@echchahyabdeljalil4700 6 лет назад

Slm

@jayphilipwilliams 6 лет назад

Spatial Light Modulator? Service Level Management (ATMF)? Sustainable Land Management? Sliema (postal locality, Malta)? Sudan Liberation Movement? Sound Level Meter? Service Lifecycle Management? Surinam Airways (ICAO code)? Single Longitudinal Mode (SONET)? Sul Livello del Mare (Italian: Above Sea Level)? Statistical Language Model? Standard Liters per Minute? Surinaamse Luchtvaart Maatschappij (Surinam Airlines)? Software Lifecycle Management? Speech Learning Model? Selective Level Meter? Signal Label Mismatch (SONET)? Standard Laboratory Module? Shining Light Ministries (Mission, TX)? Service Layer Manager (Ciena)? Signaling Link Management? System Load Module? Student Life Ministry? Shoulder Launched Munitions (MILES Component)? Ship Logistic Manager? Senior Life Master (bridge)? Subscriber Loop Multiplex? Service Life Monitoring? Short Life Memorandum (UK)? Seat Lift Mechanism (toilet component)? Sea Level Measurement? Structure Location Maps? Shear Load Measurement? Staff Level Meeting? System Library Manager? System List Model? Synoptic Lagrangian Map? Side Lobe Measurement? Ship/Submarine Logistics Manager? Submarine Launched Missile? Silver Life-Saving Medal? Synthetic Layer Microstructures? Strategic Logical Model (Sprint)? Socially Limiting Maneuver? Skip Level Meeting (Sprint)? Shoulder Launched Missile? Smart Little People (modeling)? Static Load Model? Smart Learning Module? Sport Leisure Management (UK)? Social Local Mobile (also seen as SoLoMo)? Spanish Language Media? Software License Management (also seen as SWLM)? Sri Lankan Military? Selective Laser Melting (manufacturing)? Simulation Lifecycle Management?

@mozeppa 5 лет назад

you can't see anything you are doing!

@alanex5225 3 года назад

When you take the parts you are working on out of camera it is frustrating and viewers cannot tell what you are doing. You need to edit this video to show always the parts IN THE CAMERA.

@jayphilipwilliams 3 года назад

It was a mistake in the editing process.

@johnzarollin2749 3 года назад

for heavens sake don't review the off camera shots before posting, jeeeeeze.

@johnbladen4931 8 месяцев назад

Thank You for this video but you Waffle On to much. JB

@hunter-cs3em 4 месяца назад

Get it together man. Sorry 😞 you are making it sound like you don't know what your talking about.

@johnzarollin2749 3 года назад

try reviewing what you are going to post PRIOR to posting video whose subject is off camera and not always in focus. major waste of your time, my time.