I this episode I’ll restore this old lift arm lighter from 1930. I think the manufacturer is called Polo. It has a bad spark, minor dents that need to be fixed and the plating is mostly gone. No extreme defects this time. I think the seller also accidentally sent me extra an lighter. I too has some minor dents and the plating is almost completely gone. The brass on both lighters is also patinated.
More info can be found after the links
---------------------------------------------------------------------
Check out my new Instagram: / odd.tinkering
Support me on Patreon: / oddtinkering
SOME OF MY TOOLS:
RUST REMOVER: www.mc-51thebestrustremover.c...
SCREW DRIVER SET: amzn.to/2F3n6kO
SCORLL SAW: amzn.to/31Eblej
POWER FILE: amzn.to/2URHvPq
CHUCK NORRIS’ TOOTHBRUSH: amzn.to/2YfXUj2
CORDLESS DRILL: amzn.to/2Wois77
BETTER ROTARY TOOL: amzn.to/2WF75I6
PRESS FOR ROTARY TOOL: amzn.to/2Uiv1Eu
2-AXIS TABLE FOR THE PRESS amzn.to/2WPkttl
MY FILMING GEAR:
MAIN CAMERA: amzn.to/2JvtKox
MAIN TRIPOD: amzn.to/2OlpYgn
MICROPHONE: amzn.to/2I80iDz
VIDEO LIGHTS: amzn.to/2FpJDaB
MAIN LENS: amzn.to/2Fm8yMk
CINEMATIC LENS: amzn.to/2TmNdHH
WIDE ANGLE LENS: amzn.to/2U7iJha
GOPRO: amzn.to/2U3eqU3
---------------------------------------------------------------------
SUBSCRIBE ▶▶▶ ru-vid.com/show-UCf_s...
---------------------------------------------------------------------
Restoration playlist▶ • Tool restorations
---------------------------------------------------------------------
The disassembly of this one was simple the wheel was attached with a tiny screw and the arm was held together by a spring and it was disassembled by only pressing the arm down and bulling it backwards, so it popped out of the slot. The spring was not attached in any way but it was just pinned between the arm and the body of the lighter.
I put all the parts in MC-51 rust remover which will also remove patina from the brass. This was followed by sanding out all the scratches and tiny dents. While sanding I also made a dent removal tool from a nail. This helped me to push some of the deeper dents back up. Whatever shallow pits were left from those, I sanded down. The wall was very thick, so this was no problem. After sanding, everything was polished. The shinier surface you have when you start plating, the better results you get. Also you can’t polish the plating too much because it’s thin. Some polishing can be done if you plate thick enough layer, like I did.
For nickel plating I used a nickel electroplating solution I’ve made myself. It’s essentially a nickel sulphate solution. I might do a tutorial on this at some point. This is still a very slow system but I want to figure it out myself rather than use a commercial system. That’s half of the fun. Cleaning the parts well before plating is essential.
After plating I gave the parts quick polish on some areas but mostly it looked fine after I had rinsed everything with water and got the black oxide off the plating.
While the plating was going on, It was several hours, also sharpened all the teeth of the wheel with a tiny file. Although it didn’t take many strokes on each teeth this took a good while because they were so tiny.
On previous video someone commented that I should have the wick running trough the whole lighter and before putting the cotton in and then cut it in length afterwards. This seemed to work well. Almost all comment are red and tip are listened although I don’t have time to answer most of them.
Thanks for reading all the way trough. If you have questions, leave a comment. I might answer or not, I get a lot of comments and questions so I can't answer all but I try to read it all and answer a few every day.
22 июн 2019
