No video :(

1999 Ford Ranger - Diagnose and Repair Turn Signal Failure

Подписаться 78

Просмотров 49 тыс.

50% 1

Short video on determining why turn signals failed, and how to repair. We'll discuss the first thing to check (fuses), where they're at and what to look for. In my case here, the fuses were fine and we needed to check the flasher relay, which was the culprit. We'll show how to remove and replace the flasher without removing the plastic & metal panels. For my '99 Ranger, the Motocraft flasher relay part # is SF631 which I purchased from Amazon, here's a link . . . www.amazon.com...

Опубликовано:

5 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@bigrod997 3 года назад

Best video on this repair. Very simple and easy. Watched other videos were guys were taking off the plastic cover and metal cover. All those extra steps are not needed. Just slide the relay off towards the drivers door and pop it off. That was a little tough to pop it off the clip and put the new one on. Super easy, besides the struggle with the clip. Thank you so much!

@roystake6081 3 года назад

Glad it helped 🙂

@tobylewis5787 Год назад

Thank you so much for this video. My indicators / hazards were sticking on in humid climates. Checked through the various other videos on YT and they are all pretty terrible. Most of them start with the panels already removed. Your video saved me a lot of time and effort. The only fiddly part was due to the awkward angle and tough clip on the relay / wire connector. For anyone with a 1998 Ford Explorer, the following part works fine - Standard Motor Products RY-1214 Turn Signal Relay. Got mine on Amazon for $17. A lot cheaper than the Motorcraft part. It is missing the tiny 6th pin in the corner but many others report using the RY-1214 part without issue also.

@roystake6081 Год назад

Glad to hear it was helpful Toby, and thanks for sharing the less expensive part for folks.

@josephdupont 2 года назад

I had that problem which was solved by cycling the emergency flasher several times.

@HaakSO 2 года назад

I have the exact same problem on my 2002 Ranger. What do you mean though, by cycling the emergency flashers?

@livingfree1936 4 года назад

Great video, quite helpful!

@reivajm1212 4 года назад

Nice video. The problem I have on my Truck is that when I turn the left or right signal I hear the click but it doesn't do anything on the dashboard or wont turn the signal light on. The hazardous lights blinks and work with no problm. But, If I play with the lever turning it up and down, the signal light will turn on , yet it won't blink, just solid light. Also a solid left ot right signal on the dashboard. If I let go the lever, it will turn off. And then, have to keep moving the lever until is on again, wont blink. Do you think is the multifunction switch or a bad relay? Already checked the fuses and the bulbs. Thanks in advance.

@pxods 6 месяцев назад

Thank you

@roystake6081 6 месяцев назад

Your welcome

@masonjackson565 Месяц назад

My relay isn’t in that position. I think it’s on the left side

@andrewdominguez123 4 года назад

How'd you know the part was bad? I just got hone from work and im having the same problem. Fuses are good. But what would i look for in a damaged/non-working part?

@roystake6081 4 года назад

Great question Andrew. Thru process of elimination, the flasher relay was the most likely culprit. The issue could be something else (faulty wiring, faulty turn signal switch/lever assembly, etc.), but replacing flasher was easiest (and most likely) next step. You can actually pull the flasher relay and bench test it (here's pretty good generic tutorial on how to do that . . . ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-IpRWcNoLdwQ.html ) before you buy a new one.

@bigboyzooted2638 2 года назад

I have a relay that has a extra pin in it I can’t find one that has that extra pin. Can I buy one with just 5 pins instead ?

@roystake6081 2 года назад

Not sure. If there is a number or marking on the one you have, you might try searching for that. Or search for with specific make, model & year of your vehicle. Or might just call a local parts shop, have them search for you.

@corysturgis6660 Год назад

Did you find the 6 or did the 5 pin work

@txsurfnturf 11 месяцев назад

Another videos says the extra pin is for brake lights.

@rudyr1578 2 года назад

Have an 03 with same problem. Mine doesn't have that relay at all

@roystake6081 2 года назад

Thanks for heads up re: the '03 Ranger Rudy. What did you find was the issue?

@MichaelAMcDermott Год назад

Yeah. My 2003 Ford Ranger doesn't have a relay at all. I took it all apart, and to my suprise, NO RELAY!!!! 😲

@robyabraham3283 Год назад

My ranger signal indicator not working But 4 way signal working,what is the reason

@angeblitoherrera Год назад

That's the fuse for hazard lights

@Korrea00 3 года назад

Will this fix the hyper flash?

@sleebbie 2 года назад

Hyper flash is usually caused by using LED blinker lights. A stock flasher will not fix that issue, you need a flasher for LED lights. You want an EP27 flasher, they are sold on Amazon, Ebay, etc.

@HaakSO 2 года назад

I have the EXACT same problem