Don't Replace ABS Module Before Watching This | Part 2 | ABS Module Components Test

Automotive Diagnosis: Cars Repair &Training Guides

Подписаться 47 тыс.

Просмотров 61 тыс.

0% 0

This video is the second part of ABS Module test and repair. In part 1 I explained how to test the ABS circuit, board and explained the ABS Module wiring and internal structure. I also explained how to test the ABS Module for Valve relay error fault or for ABS Motor Electrical fault.
But in this video I will go further to explain how to test the MOSFETs and Solenoid valves inside the ABS Module. I also explain the difference between ABS and ESP/TCS in terms of internal structure and how to know the normal value for the components during the test.
Part 1 of this video can be found in my channel or using the link below:
• Don't Replace ABS Modu...
Join the channel for more videos and more support:
www.youtube.com/@AutomotiveDi...
You can also find the ABS internal diagram that I presented in the video in the following link:
drive.google.com/file/d/1Pzz8...
And for downloading the ABS internal components diagram use the link below:
drive.google.com/file/d/1jbpZ...
Finally a Perfect Budget Friendly Scanner for DIY & Pro Mechanics That Can Do Everything !!!
• OTOFIX Lite Review | A...
#ABSmodule
#how to repair ABS Module
#RepairABS
#tcs
#esp
Disclaimer:
Any information contained in this video is just the understanding of “Automotive Diagnosis: Cars Repair & Training Guides” and it is not an official guide or reference, so everything provided in this video is just a share of our experience and understanding and they are provided as a courtesy for your reference only. So, if you are using any part of this video, use the information at your own risk. We highly advise you to check the manufacturer owner’s manual before performing any act of removal, diagnosis, inspection, or repair on your car to know about what you are authorized to do on your car, what the correct and legal procedure is and what risks might be involved, also viewers are strongly advised to consult a licensed person before any sort of inspection or repair. Due to the factors beyond the control of “Automotive Diagnosis: Cars Repair & Training Guides”, we cannot guarantee against improper use of information or tools or systems, or the procedure provided. “Automotive Diagnosis: Cars Repair & Training Guides” disclaims any damage, injury or loss caused by your decision to follow the steps provided in this video.

Авто/Мото

Опубликовано:

22 май 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 219

@AutomotiveDiagnosis Год назад

Please watch the Part 1 of ABS Module Test & Repair in the following link: Don't Replace ABS Module Before Watching This | Repair ABS Module for Motor & Valve Relay Error ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-kUGL53kNXSE.html

@Ed-ty1kr 18 дней назад

Thorough explanation of how the part functions and how to check common issues. Outstanding information.

@AutomotiveDiagnosis 17 дней назад

Thanks for watching. I’m glad you liked it.

@stephendennis7871 Год назад

Another excellent follow on video to the first one, very informative with clear video pictures to go with the explanation

@AutomotiveDiagnosis Год назад

Thanks a lot for your comment.

@josephmcmonagle5901 2 месяца назад

That was totally amazing. Thank you so much for taking the time to make these videos.

@AutomotiveDiagnosis 2 месяца назад

Glad you like them!

@cliveradvan3414 4 месяца назад

Fascinating insight! Thank you so much for your great presentation.

@AutomotiveDiagnosis 4 месяца назад

Glad you enjoyed it!

@giterdunpete Год назад

I think these 2 videos go a long way to explaining the error codes in BMWs which a mechanic is never going to string together with an electronic fault. And just removing and replacing the large connector is a WORK AROUND which if it works is destined to fail again. So well done .

@AutomotiveDiagnosis Год назад

Thanks a lot, I'm glad you liked the video.

@arazaliguliyev Год назад

i was looking for such an educational chanel like this👍

@AutomotiveDiagnosis Год назад

Hi my friend and thanks for your comment. Welcome to this channel, I'm glad you found it helpful. ❤️

@ScientistPrepper 9 месяцев назад

Great video. I learned a lot. I'd like to see another video in the abs module series.

@AutomotiveDiagnosis 9 месяцев назад

Thanks 🙏, more videos are coming about ABS module

@drissjakane2683 8 месяцев назад

Thank you so much for this practical video this all waht we need to learne how to controle moduls👍

@AutomotiveDiagnosis 8 месяцев назад

Hi my friend. I’m glad you liked it.

@mohammadal-gebaly3046 Месяц назад

Thank you very much , professional job , I enjoyed it , watching you from Egypt , appreciated

@AutomotiveDiagnosis Месяц назад

Hi my friend, thanks for watching

@GarethDavies-hk9cg 3 месяца назад

Thank you for two very interesting videos.

@AutomotiveDiagnosis 3 месяца назад

Glad you like them!

@agdoservice 10 месяцев назад

Excelente vídeo ! Parabéns ! Sua disposição para ensinar e algo divino ! Feliz por sua disposição,Obrigado.

@AutomotiveDiagnosis 10 месяцев назад

Thanks for your kind words. I’m glad you found the video useful.

@cartech5015 Год назад

Perfect explanations.

@AutomotiveDiagnosis Год назад

Thanks

@NishanthaMillagala 11 месяцев назад

Dear sir Its very nice explain. Thanks so much .

@AutomotiveDiagnosis 11 месяцев назад

I’m glad you enjoyed it 🙏🙏❤️

@amarabdelli487 Год назад

Thanks for sharing, perfect explanation

@AutomotiveDiagnosis Год назад

Thanks for your comment.

@esmfamil3929 Месяц назад

A nice and helpful explanation , thanks a lot .

@AutomotiveDiagnosis Месяц назад

Glad you liked it

@antonispk6760 16 дней назад

Very helpfull video !!

@AutomotiveDiagnosis 16 дней назад

Glad it was helpful!

@maar5725 Год назад

بعد شُكر الله ؛ شُكراً لــككك ؛ Thank you very much Good steps

@AutomotiveDiagnosis Год назад

Thank you very much for your comment.

@luisramos3427 5 месяцев назад

Super helpful!👍👍👍👍👍

@AutomotiveDiagnosis 5 месяцев назад

Glad you think so!

@mariocarmecanicaautomotiva8602 3 месяца назад

Estes dois vídeos me ajudaram muito aqui no Brasil, total gratidão por compartilhar seus conhecimentos, peço que Deus te abençoe grandemente

@AutomotiveDiagnosis 3 месяца назад

Hi my friend. Thanks for your comment. I’m glad videos were helpful.

@dipakmanu1842 Год назад

Thanks a lot, I have watched the first one more than 5 times I think 😊 this one is great too ❤

@AutomotiveDiagnosis Год назад

👍👍❤️❤️

@shaunchetty4223 20 дней назад

Awesome

@TripleBRanch 2 месяца назад

@AutomotiveDiagnosis thank you for the video. I checked everything you checked and all tests were good. The original fault code was “C2200 Antilock Brake Module Internal”. I would guess the trouble will still be there if I just reassemble… my car is a 2015 Jeep Wrangler JK. Any advice will be greatly appreciated.

@gcauto6946 Год назад

Thanks for the great job! See if you can make a following video, to explain the operation of the MCU and the controller, Thank you!

@AutomotiveDiagnosis Год назад

Thanks for your comment. Sure thing, I will try to do my best 👍

@bwagizoselemani8434 Год назад

Thenk you sir for a good lesson

@AutomotiveDiagnosis Год назад

I'm glad you liked it.

@user-tt4xy9rd4s 10 месяцев назад

thanks, useful information

@AutomotiveDiagnosis 10 месяцев назад

So nice of you

@suatkaleli5075 28 дней назад

better than others thanks

@AutomotiveDiagnosis 28 дней назад

Thanks for watching

@bluedeckelectronics 11 месяцев назад

Good video !

@AutomotiveDiagnosis 11 месяцев назад

Glad you enjoyed it

@LooneyRanger Год назад

Perfect. Tq u so much

@AutomotiveDiagnosis Год назад

❤️❤️

@johnreyzabala3163 9 месяцев назад

wow great nice video

@AutomotiveDiagnosis 9 месяцев назад

Thanks, I’m glad you liked it

@sandyshrimp8463 Месяц назад

This was a great video. I checked the motor mosfet (mine is a PN0404 for a jeep) and have an OL reading between the gate and the drain. Should I assume the mosfet is bad? thanks again for the video and for any help you can provide.

@ravigarage8745 Год назад

Excellent

@AutomotiveDiagnosis Год назад

👍👍👍

@juvehe Год назад

This is very cool! Thanks for sharing your knowledge.

@AutomotiveDiagnosis Год назад

Glad you liked it and thanks a lot for your comment.

@juvehe Год назад

@Automotive Diagnosis: Cars Repair &Training Guides if I can suggest one thing to make your awesome video more awesome: show how to check integrated circuits. I have an MK60 module off of a 2002 BMW 325i, got the trifecta lights on my dashboard. Turns out I have a bad IC (9369.1D).

@juvehe Год назад

@Automotive Diagnosis: Cars Repair &Training Guides in case anyone is curious, the error code I get is 5DF5: ABS-DSC internal fault, control unit.

@AutomotiveDiagnosis Год назад

@@juvehe Hi there, Thanks a lot for your comment and sharing your experience. I explained more on the first part of this video but as you said there is more way to go and hopefully I can make another video too.

@AutomotiveDiagnosis Год назад

@@juvehe Thanks a lot for sharing your experience.

@somarpr 4 месяца назад

Excellent video, great explanation in this excellent course on how does a ABS module works and I can relate it to how intermittent ABS should be worked and diagnosed. Thank you. What did you use to close it back and water proof it.

@AutomotiveDiagnosis 4 месяца назад

Glad you enjoyed it! I usually clean up the old seal and apply new black silicone.

@maar5725 Год назад

بعد شُر الله ؛ شششكراً لّككك ،،، Thank a lot ,,, You did great job in very excellent demonstration I ever seen .

@AutomotiveDiagnosis Год назад

Thanks a lot. I'm glad you liked it.

@gabrielgv252 6 месяцев назад

Excelent video

@AutomotiveDiagnosis 6 месяцев назад

Thanks

@longhuynh5249 11 месяцев назад

Brilliant indtructions

@AutomotiveDiagnosis 11 месяцев назад

🙏🙏

@i.fix_iran6097 7 месяцев назад

good job👍

@AutomotiveDiagnosis 7 месяцев назад

Thanks for the visit

@sahsaker 10 месяцев назад

1st thank you very much if this great vedio I meet 2 times problems with my car 1 st one the module stoped because the vacuum pump not working but motor working properly I changed already abs unit 2nd one after time too have a problem get the oil from pump to module Now I want to repair the old pump but the pins on not released this pins on motor head inside the pump

@AutomotiveDiagnosis 10 месяцев назад

Hi there, I didn’t quite get the question, is there any fault code right now? If brake fluid is not coming into ABS module, this is not the ABS motor fault, you must check the master cylinder.

@watkinsrcful 9 дней назад

Thank you

@AutomotiveDiagnosis 9 дней назад

Thanks for watching

@user-ii1un6fq3h 9 месяцев назад

Best ever

@AutomotiveDiagnosis 9 месяцев назад

Thanks

@Walopa_uie 3 месяца назад

sir i check all mosfet is good .. the error code is u3000 hope you notice this one sir thank you for sharing👍👍👍

@leethomas9198 8 месяцев назад

Thank you for identifying the electrical components. Where is a good source for these components and tech sheets besides Google?

@AutomotiveDiagnosis 8 месяцев назад

Wiring diagram is better than any other source.

@dapurperadaban7710 10 месяцев назад

Thank you very much, this is great explanation, do you have any video for how to check the IC5895-5220C if there's IC fault, how to check it? and how to scan it directly the ABS module in bench (pinout connection to OBD scantool). can you share the diagram for Ford Fiesta 2011-2014. again, thank you very much!

@AutomotiveDiagnosis 10 месяцев назад

Hi there, we don’t have any videos for inspecting that IC, but I will try to get one.

@176robles 8 месяцев назад

MY Grand Vitara 2011 ABS is near desame, where can a get wiring diagram like this one you have?

@mazdaservice6533 Год назад

Thanks bro

@AutomotiveDiagnosis Год назад

👍👍

@greggutierrez7760 3 месяца назад

Great instructional videos on ABS module operation and diagnosis. My question is, if you cut the plastic cover off then how do you ever re-use the module if it tests good? Seems like this is destructive testing? Good to know if you're just interested to see where your old module failed but not useful for actual repair correct?

@AutomotiveDiagnosis 2 месяца назад

Hi there, of course we seal the cover back on, unless what’s the whole point of testing the unit? So, we must be very precise when removing the cover, then we seal it back on.

@OnYok1974kuwait 3 месяца назад

👍👍👍

@AutomotiveDiagnosis 3 месяца назад

👍👍

@matmechanic5909 Год назад

Thanks

@AutomotiveDiagnosis Год назад

👍👍

@newyorkerturbo 7 месяцев назад

hello what an explanatory video are you giving me the courage to do it too, I tell you that I have a 2008 jeep grand cherokee with a similar module I have the DTC C2200 the only thing I have seen with the scanner is that the valve feed oscillates between 5 and 10 volts before the DTC appears when starting the vehicle and exceeding it of 15 miles the lights come on and in the scanner the valve feed is It's still at 5 volts, do you think I could fix it if I open it? 🤔

@AutomotiveDiagnosis 7 месяцев назад

Hi there, thanks for your comment. This code is due to an internal failure on ABS Module, Sometimes it could be something we can find by checking all connections in the ABS module, but sometimes is coming from the main microprocessor which is hard to repair. So basically there could be different possible causes for each different case, and we can only be sure after inspecting the module carefully and thoroughly.

@supercomputerbug 11 месяцев назад

please show how to verify opening function of mosfet. if i am right, by charging the gate by touching with + of multimeter, the mosfet opens.

@IdaIda-vx8hp 2 месяца назад

Thank your explanation, I got the problem the resistance are different 2 ohms between blue, 9 ohm and 8.8ohm this acceptable? , my car problem abs right rear cannot detect.

@AutomotiveDiagnosis 2 месяца назад

HI there, that much difference is not a big deal. May I ask the fault code too?

@drv8086 7 месяцев назад

Okay dude, you gotta tell me, where did you find these diagrams. It’s exactly what I was looking for! Edit: thank you for this wonderful video btw

@AutomotiveDiagnosis 7 месяцев назад

Hi there, thanks for watching the video, there are different ways we can find the wiring diagrams, Some manufacturers have designed the OEM scan tool with wiring diagrams (KIA, Hyundai, SsangYong etc.) so if you have those scan tools, you have the diagrams too. Also, in addition to the manufacturers technical websites, some other private companies offer the wiring diagrams and workshop manuals too.

@drv8086 7 месяцев назад

@@AutomotiveDiagnosis that’s fantastic, I’ve been really struggling to find the wiring diagram of my 04 Kodiak Topkick. I may have to look into some of those private companies or scan tools you mentioned. I saved the ones from your description and I can’t tell you how much it helped. Thanks again!

@AutomotiveDiagnosis 7 месяцев назад

@@drv8086 I'm glad it was helpful. I will check for that wiring diagram as well and will keep you posted here if I find any.

@drv8086 6 месяцев назад

⁠@@AutomotiveDiagnosisThank you so much, if you do happen to find anything it would be very much appreciated. I’m still having trouble diagnosing exactly what’s gone wrong. A diagram such as what you have outlining the pin out would be wonderful!

@ronlisto4790 11 месяцев назад

Great video. Question: 2009 Ford Escape with very low brake pedal. No codes or lights. Replaced master cylinder, all shoes & pads good. Had shop bleed ABS module with scanner. No change, still very low pedal. Is ABS module causing this? Thx

@AutomotiveDiagnosis 11 месяцев назад

I don't think that's ABS fault, if it is, it shows itself when you do the bleeding. Pedal is low, but how you feel the pedal?

@leethomas9198 8 месяцев назад

The low pedal position could be the end of the rod connected to brake pedal. Most Fords have an adjustable screw on end. I think it is a 7mm and you can lengthen it to cause pedal to react quicker.

@unclefranko2452 11 месяцев назад

Hi mate ,good video, how do you manage to get the cover off ???? Please regards Frank

@AutomotiveDiagnosis 11 месяцев назад

Thanks for your comment. I simply use a small cutter to do it carefully.

@humbertholzmann674 2 месяца назад

nice video but at the end can it be repaired fixing soldering?

@AutomotiveDiagnosis 2 месяца назад

Of course it can, if there is any broken solder, it could be the source of the problem. But as I said, that’s not the only possible cause, there are many other causes that are explained in the video.

@sangeethkumar6727 20 дней назад

Where can we get the schematic diagrams of the electronic components of the ABS ECU and the hydraulic schematic of the ABS valve body for other cars

@user-wd8kv9yf4c 7 месяцев назад

Excellent video. What about when a component is faulty. I have an abs error code indicating a wheel speed sensor problem but everything is fine. The problem is probably within the abs module. The question is which faulty component of the module will keep the brakes locked on one side only when the abs light is lit and the brake pedal not depressed?

@AutomotiveDiagnosis 7 месяцев назад

Hi there, that problem could be coming from the ABS valves, but you need to check the brake caliper as well, sometimes brake piston or sliding pin is sticky.

@user-wd8kv9yf4c 7 месяцев назад

Can the ABS module can be damaged if the wire harness cause a short because of a shafted wire connecting to the ground? Or the module is protected somehow in these situations.

@mofeedfouad7391 11 месяцев назад

First of all thank you for your efforts I have jeep grand cherokee 2011 my front wheel lock properly but my rear wheel not lock the wheel enough, I have changed everything but not the abs because there's no abs or any light in shown im my dashboard, And when I try to bleed the rear ones the brake oil the pressure of it approx. Nothing compared to front ones Do you have any advice?

@AutomotiveDiagnosis 11 месяцев назад

Hi there, Have you checked the master cylinder?

@mofeedfouad7391 10 месяцев назад

@@AutomotiveDiagnosis Yes already replace it with new mopar

@KPoth-hj3mh 4 месяца назад

thank you for sharing. where we can find the wiring for an ABS unit? I have a ATE controler 28.5162-2917.3

@AutomotiveDiagnosis 4 месяца назад

Thanks for watching. I normally get the diagrams from the dealers technical website or those online websites offering the diagrams for a fee. But not all of those diagrams provide enough details. May I ask what model your car is?

@athulprakash77 9 месяцев назад

I bike lever is harder when applied front abs brake what cause the problem i get the braking but its little tight

@lsp5745 4 месяца назад

Hi, I'm getting this code. Everything I checked with your vids is OK. mosfet Ok. C1043: Master cylinder cut solenoid valve circuit No.1 failure

@AutomotiveDiagnosis 4 месяца назад

May I ask your can make and model?

@lsp5745 4 месяца назад

@@AutomotiveDiagnosis Yes! Suzuki Grand Vitara Year 2012. Where are the transistors for the solenoids? The two mosfets seem to be Ok, following your indications. Also I tried to look for the pinout of two big chips on the card, but can't find the datasheet.. I've got some electronics experience so I'm trying to solve it myself...Thanks!

@RianKurnia 10 месяцев назад

Penjelasan yang mudah dipahami. Saya ingin bertanya pada anda, bagaimana cara memeriksa kode kesalahan u3000 pada modul abs ford fiesta? Mohon dijawab, terima kasih.

@AutomotiveDiagnosis 10 месяцев назад

Hi, for this code you need to check the power and ground on ABS Module and also CAN-BUS terminals.

@JEscGod 4 месяца назад

Hi, i have a 2012 chevy equinox with ABS, brake and stability track lights on at same time, do you think the ABS module can be repaired?

@AutomotiveDiagnosis 4 месяца назад

You must check the fault codes first, sometimes it’s not a very serious issue

@eluno72 3 месяца назад

Hello ! I have a problem with a 2013 terrain ABS module, the code is U0073 00! I try to buy a new module and program it but it is impossible to get it. Could you guide me if it can be repaired or tell me what I should check? Thank you

@IgorReviews 6 месяцев назад

Хорошо, что английский я знаю)

@AutomotiveDiagnosis 6 месяцев назад

😊👍

@user-rc2yw1bc9f 9 месяцев назад

Make a video on Hyundai ABS please

@AutomotiveDiagnosis 9 месяцев назад

Sure thing

@juanjoalbarello442 3 месяца назад

is this ABS Module from a Ford Focus SE? because is very very similar...

@AutomotiveDiagnosis 3 месяца назад

No my friend, but very similar

@carsmobileservice1846 Год назад

Do you guys have any video about electric parking brake too?

@AutomotiveDiagnosis Год назад

Yes, we do a couple of videos for EPB on different cars (more vides are coming though), I will send the link here.

@AutomotiveDiagnosis Год назад

How To Release Electronic Parking Brake on Mercedes CLA 45 Before Replacing the Rear Brake Pads ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-r7q_WextBwQ.html

@AutomotiveDiagnosis Год назад

How to Fix C10E254 Fault Code on VW Golf Electronic Parking Brake (EPB) Just in 2 Minutes ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-zRd48AoQISE.html

@Walopa_uie 4 месяца назад

sir i check all mosfet and all coil is good.. my final is cpu or ic ?? do you think im right, if change ic , need to program sir or no need..thanks for helping sir,gdbless

@AutomotiveDiagnosis 4 месяца назад

Hi my friend. May I ask what is your fault code exactly?

@Walopa_uie 4 месяца назад

@@AutomotiveDiagnosis u3000 49-68 control module, panel lights on abs, traction and steering angle sir..

@Walopa_uie 4 месяца назад

@@AutomotiveDiagnosis not steering angle sir the other one light is uphill..

@ratheeshkrishnan1623 10 месяцев назад

Can you do the video of Bosch abs 5.3 module

@AutomotiveDiagnosis 10 месяцев назад

Hi there, I will, as soon as I have that module.

@geodirecoes2778 9 месяцев назад

Eu sou do Brasil, muito sua boa explicação!! Estou com problemas em um abs do ford FUSION!! Vc poderia me ajudar?

@AutomotiveDiagnosis 9 месяцев назад

Hi my friend, I try to do my best, what is the problem with your ABS?

@geodirecoes2778 9 месяцев назад

@@AutomotiveDiagnosis ele não comunica com scanner

@geodirecoes2778 9 месяцев назад

Quero um treinamento guiado com você !

@AutomotiveDiagnosis 9 месяцев назад

@@geodirecoes2778 When there is no communication, it could be power supply, ground or CAN-Bus problem. It's better to start from Power supply on ABS module, normally there are 2~3 power supply, one is for ABS motor, one is for ABS valves and the last one is for ABS control module, the last one is very important for the communication. If power is okay, find the pins for ground and inspect them. ABS connector also must be carefully checked for any dirt, moisture or looseness.

@geodirecoes2778 9 месяцев назад

@@AutomotiveDiagnosis muito obrigado pela atenção, vou verificar

@user-tl3gp8re3r 4 месяца назад

Ola,queria saber teste para código U3000 Ford New fiesta ,falha eletrônica interna

@rhinoleveling 11 месяцев назад

I have a unit like this one. ATE MK60E it keeps throwing C2200-49 internal module failure. I have already verified that motor & valve circuits are good. I'm scratching my head on this one. Any insight would be greatly appreciated.

@AutomotiveDiagnosis 11 месяцев назад

Thanks for sharing your experience. If you have checked the components as described in this video and part 1 (link in description), it could be the control unit failure which does not switch the actuators on.

@rhinoleveling 11 месяцев назад

@AutomotiveDiagnosis sounds correct when I clear the code it's fine, has bidirectional comm. Until wheels start rolling as soon as I hit 2 mph, it comes back

@braddunn5983 9 месяцев назад

@AutomotiveDiagnosis what do you check or replace for this situation, where the control unit doesn't turn it on?

@alimuddin3018 5 месяцев назад

@@rhinoleveling I have same problem too.dont now what to do

@stevowhit3121 5 дней назад

Great info. I have a 2013 Ducati Multistrada with bosch abs. I get a random """abs pressure sensor fault.: C1006, C1007""". Totally random sometimes not for hundreds of miles other times every 25? The fault resets when ignition is off / on. I have bled and flushed both front and rear many times with quality brake fluid. Abs operates when not faulted. When faulted the brakes are fine except no abs function. Ideas please. Thinking of pulling the module and checking solder joints. It seems like a bad connection due to the intermittent occurrence of the fault. Anyone having pressure errors faults ? All info I get is to replace module. Thanks in Advance. Cheers

@zackkennedy9266 9 месяцев назад

Hey if a mosfet is bad can it throw off the modfest next to it when doing the diode funtction test

@rogerbsp1 5 месяцев назад

Hi there, it's possible communicate abs module with scanner without the others modules? I'm trying but the communication don't starts.

@AutomotiveDiagnosis 5 месяцев назад

Hi there, I didn’t quite get it. You mean ABS doesn’t communicate with scan tool or it doesn’t work with other control units?

@rogerbsp1 5 месяцев назад

@@AutomotiveDiagnosis I was trying to connect the scanner directly to the abs module, but the communication was not working. I even tried with a 120 ohm resistor between the CAN H and CAN L lines, but it still didn't work. So I connected the injection module to the CAN H and CAN L line and this time I managed to communicate with the scanner.

@Sunny-uk5fn 7 месяцев назад

Would be interesting if this solves the error code C1288, error at ABS pressure sensor

@AutomotiveDiagnosis 7 месяцев назад

It’s a bit complicated for the pressure sensor as it’s controlled completely by the control unit, but it is absolutely possible.

@japzonerazan744 6 месяцев назад

You can fix the code c1288 by changing the brake cylinder may be its defective, or the fluid is contaminated , this 2 are the reason why creating of pressure to the brake system,

@giulianofabbrinioficial Год назад

how can i fix, test or replace the pressure sensor? tks

@AutomotiveDiagnosis Год назад

Hi there, Pressure sensor is the hardest one as it senses the pressure and gives it directly to ABS module, so the only section to check is the contact between the pressure sensor and ABS module. In most cases we have to replace the ABS module is case of having a faulty pressure sensor.

@pedroqueiroz8097 6 часов назад

Ola .tem curso reparo ecu abs?

@AutomotiveDiagnosis 6 часов назад

Hi my friend. We are working on some courses including the ABS, will let everyone know as soon as they are ready.

@revbikerbigd8664 2 месяца назад

2014 f150 has a code C1440 can i repair my module??

@AutomotiveDiagnosis 2 месяца назад

This is a tricky one, most of the times the entire ABS module must be replaced.

@germany4650 Месяц назад

здраствуйте, я все видео до конца посмотрел но так и не понял именно в чем было проблем? потому что у меня не удаляется это ошибка c2112

@AutomotiveDiagnosis Месяц назад

Watch this video for C2112: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-F2RiGkoK9_g.htmlsi=xFe4fstEajurNX_x

@raulfloresreyes2112 10 месяцев назад

tengo dudas cuando el modulo de abs marca el codigo de falla ABS ACTIVADO cual seria la solucion en este caso?

@AutomotiveDiagnosis 10 месяцев назад

Please send the entire fault code here

@zola1981 8 месяцев назад

My ABS module was failing. The motor remain ON even if I close the car. I soupose the transitor it's remain blocked ON or the microcontroller gives power to the transistor...

@AutomotiveDiagnosis 8 месяцев назад

Hi there, yeah, it could be a short to power or ABS unit malfunction. Most likely there is a fault code as well.

@ponchoaag 7 месяцев назад

do you have a diagram specific for a MB c 280 2009 2009 MERCEDES-BENZ C 280 (204.054) WDDGF54X69F166637. Im really trying to verified and repair the module , because no body could do it , so want to try.

@AutomotiveDiagnosis 7 месяцев назад

I will check and send the diagram here if I have any.

@Gerber_Gaitan 9 месяцев назад

For Mazda 3 2010 mechanical ?

@AutomotiveDiagnosis 9 месяцев назад

And what is the problem exactly?

@carlosg802 10 месяцев назад

abs engine will have oil leak inside just like it happens with master cylinder please answer me appreciate

@AutomotiveDiagnosis 10 месяцев назад

Hi there, I didn’t quite get the question, you mean break fluid leak inside the ABS module?

@carlosg802 10 месяцев назад

im sorry my friend i was trying to said is the abs motor if is leaking interior like happing with master cylinder brake

@carlosg802 10 месяцев назад

abs motor not module

@AutomotiveDiagnosis 10 месяцев назад

@@carlosg802 I haven't seen any internal leak on ABS motor, but internal leak on valves is possible.

@timrogers4124 10 месяцев назад

where do you get your drawings?

@AutomotiveDiagnosis 10 месяцев назад

In some cases, I get them from the companies technical websites, some companies like Kia and Hyundai provide the wiring diagrams on their scan tools too.

@ratheeshkrishnan1623 10 месяцев назад

If remove electronic control module and can drive the car

@chaunguyen5102 3 месяца назад

this bmw abs series ?

@AutomotiveDiagnosis 3 месяца назад

This was not for BMW but they are very similar

@justme8956 9 месяцев назад

Wer was the problem, most o them ,just bad contacts, main processor or conscription plug

@AutomotiveDiagnosis 9 месяцев назад

Yeah, absolutely, most of the times it’s poor connection.

@mohanraj2398 6 месяцев назад

i20 ABS 3 wheels bleeding. But one wheel not bleed.. what's problem????

@AutomotiveDiagnosis 6 месяцев назад

You mean it keeps giving air bubbles from that wheel?

@mohanraj2398 6 месяцев назад

@@AutomotiveDiagnosis 0% oil flow in 1 wheel

@netoferreira8708 Месяц назад

I have error code b1342 on my Ford Fusion 11. Have you ever caught anyone with this error?

@AutomotiveDiagnosis Месяц назад

Hi there, this code has many different possible causes, have you checked other systems as well for any fault code?

@LooneyRanger Месяц назад

I have code eror c0082 and u0415, what i am chek

@LooneyRanger Месяц назад

Mazda biante skyactive

@AutomotiveDiagnosis Месяц назад

@@LooneyRanger I would check the ABS module connector first, then check the ABS fuse inside the engine fuse box.

@netoferreira8708 Месяц назад

@@AutomotiveDiagnosiswithout other errors. I have already checked the wheel sensors and the ABS works and does not lock the wheels. I will send it for repair. grateful.

@abdulhamza920 10 месяцев назад

iam working on peugeot 301 abs i daignose it i find front right sensor and front left sensor not working and i opent it i fund some line on the board and i repair it and fix it back he didni worh so i need some help thank

@AutomotiveDiagnosis 10 месяцев назад

Have you checked the wiring between ABS module and sensors?

@northernpatriot9078 Год назад

What if its on yhe car with wires

@AutomotiveDiagnosis Год назад

There are some other videos on the channel explained those how to check the ABS module on the car too, I will send the links here.

@AutomotiveDiagnosis Год назад

How to Test & Fix the C2112 ABS Valve Relay Error | ABS & ESP Fault Code ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-F2RiGkoK9_g.html

@AutomotiveDiagnosis Год назад

How to Test & Fix C1266 ABS or ESP Valve Power Circuit Failure on Ford | ABS & ESP Fault Codes ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-NTCEF8FSqTM.html

@mrklobouk 4 месяца назад

This is from bmw?

@AutomotiveDiagnosis 4 месяца назад

No, it’s a Chevy,but they are mostly the same .

@jancloddlafront9185 3 месяца назад

oh great... class but you are not actualy trying to fix this module and neither are you offering a solution to fix the problem, Right? that some info I didn't understand anywhere on the 2 videos... great stuf any way. But have you even found a problem on an Abs module this way?

@AutomotiveDiagnosis 3 месяца назад

These two video are not only for one single fault code, there could be multiple faults on ABS module, that’s why I explained how to check the internal components one by one. I think the solution are very clear, you see how to check any of those components, so if there is anything wrong in your inspection, you have to proceed to repair. For example, any fault on ABS motor or valve relay circuit can be checked step by step by following the videos.