2000-2006 Nissan Sentra Thermostat Replacement

Подписаться 6 тыс.

Просмотров 82 тыс.

50% 1

****Disclaimer**** Due to factors beyond the control of MACHINEHEAD REPAIR PROJECTS, we cannot guarantee against the improper use or unauthorized modifications of this information. Make sure you check with your manufacturer to make sure this will not affect your factory warranty. MACHINEHEAD REPAIR PROJECTS assumes no liability for property damage or injury incurred as a result of any of the information contained in these videos. Use this information at your own risk. MACHINEHEAD REPAIR PROJECTS recommends safe practices when working with tools seen or implied in our video and written content. Due to factors beyond the control of MACHINEHEAD REPAIR PROJECTS, no information contained on this RU-vid channel shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this content is the sole responsibility of the user and not MACHINEHEAD REPAIR PROJECTS.

Авто/Мото

Опубликовано:

25 апр 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@keyboardsamateur 3 месяца назад

The same machinery lies under Hood of Almera N16 (2006, 1.5 MPI). THANK YOU FOR THE VIDEO 😊

@skywind007 2 месяца назад

Nice video. I knew the procedure but was unsure about the gasket. I remember my old Jeep was a nightmare to replace the thermostat. Those old Jeeps had a completely useless paper thin gasket. The good news is that if you needed a "coolant sprinkler", Jeeps can function as that. Nissan is way better. Thank God.

@carlsherman4095 3 года назад

Sent this video to my gf who lives across country. Very helpful and much appreciated.

@adolfojuarez3654 2 года назад

Very good and easy explanation

@joseesquivias3078 2 года назад

Also thank you for explaining on how not to overtighten.

@adityathakur5766 2 года назад

Nice explanation

@solomonchoo4967 Год назад

Thanks

@adityathakur5766 2 года назад

lovely nice explanation ❤️

@neilswan8015 Год назад

Thanks, I need to change mine soon.

@chasecochran2173 5 месяцев назад

Pulled mine out no issue except for some coolant spilling onto the trans. The gasket was dry rotted the car was so neglected by the last owner 💀

@symphonychanel 2 года назад

Well here goes nothing… thanks for the video.

@stevex7479 Год назад

U have the video for the dip stick?

@meTimetraveler 3 года назад

use an air compressor to pop the broken dip stick out. connect the air to the valve cover ...has to be direct no PCV in the path of the air flow.

@robertorodriguez9668 3 года назад

Did this fix ur overheating?

@BILLBADASHAW2011 2 года назад

FIRST THINGS FIRST. ALWAYS WHEN DEALING WITH NISSAN AKA INFINITI COOLANT PARTS. USE """"""""""OEM""""""""""" REPLACEMENT PARTS !!!!!!!!!!!!!!!!!!!!!!!

@rockayeh3277 2 года назад

That looked easy enough but you said put the pin in the same place but you just put in the re not where you took it out from.. does it not sit well if it's in the wrong spot?

@chille17 3 года назад

Nice video! So how do you replace the water control valve? I didn't know that was another thermostat. Is it directly behind the thermostat you just replaced? I replaced my thermostat but still no heat.

@paulpatriot1776 2 года назад

I’m surprised you didn’t replace the cover gasket.

@flaboi404 4 года назад

What's the best way to bleed the 2006 Nissan Sentra 2.5

@davidm3210 3 года назад

I have a '05 1.8L and there is a bleeder screw on the thermostat cover - it's near the top one of the three bolts. Check to see if there is a screw that is clearly not for mounting purposes, that may be it.

@joseesquivias3078 2 года назад

I broke my housing so i will be going to the junk yard i dont know how i cracked it i guess i tighten it to much what a bumber and also damaged the new thermostat and im pretty sure they gave me the wrong one it didnt fit through the whole and i guess i thought buy trying to just install it and tighten it would just go to place but i was wrong.

@davidm3210 3 года назад

Rock on dude, keep up those B15 Videos! Also, there's a bleeder on that housing. My lower hose is cold after a radiator swap (maybe I'm just noticing) so off I go. I'm not too upset as I didn't remove the engine block drain plug, so I reckon it was only a partial coolant change anyway. UPDATE: No go on the thermostat replacement - the gasket completely melted the 15 yr. old therm. onto the housing (not the cover). Maybe I'll try to tear it apart with a pick, and then pry it out with a pliers.