2005 GMC Sierra AEM Wideband Install

Подписаться 116

Просмотров 12 тыс.

50% 1

I installed an AEM 30-0300 wide band kit in a 2005 gmc sierra.this would be the same process for a 2003-2007.5 Gm truck and would probably be the same steps for any vehicle. This is mainly meant to aid someone who is unsure of the process for installing a wideband and also to help guide someone who's installing one.

Опубликовано:

4 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 28

@adriancervantes19 5 лет назад

Best detailed install video I've seen for these kind of trucks, looking forward to more content bro! as I have a lq4 swapped Silverado with a 228/232 tsp cam 👌

@gmckid9166 3 года назад

I’m just now getting into this more, I lost my password for a while. You still have your Silverado?

@lordandprotector 5 лет назад

PLEASE don't start the engine on a hot sensors. When the gauge says "HEAT", it's not kidding around. The sensor's ceramic element is heated up to over 1000F ( yes thousand degrees ). Then, gets hit by cold startup exhaust gas. This is the #1 cause of early sensor death.

@gmckid9166 5 лет назад

Thank you for that information. I normally don’t start the truck on a hot sensor, I was checking to make sure the sensor worked before starting the truck.

@lordandprotector 5 лет назад

@@gmckid9166 Ah, ok. I just cringe whenever I see that done. Those sensors are EXPENSIVE ! And then people complain that they die. I don't know why that info isn't the 1st thing in the manufacture's instructions.

@ismaelcarrillo3956 3 года назад

So if the sensor is hot doesn't that mean the engine is still hot? I would think the sensor cools faster than the engine.

@lordandprotector 3 года назад

@@ismaelcarrillo3956 No. The sensor has its own electrical heater. As soon as the gauge has power, it starts heating the sensor up to 1450°F ( Hotter than expected EGT ). And, even on a warm engine, the first few turns of the crank are cold ( no spark ), until the ECU syncs up with the trigger wheels..

@carguy1013 3 года назад

@@lordandprotector so in that case how long does one have to wait to re start the car? , This seems like a big problem I mean what if you have to shut the car off at the petrol station after a few runs and then start it after filling up?

@russellallen1976 2 года назад

You need your sensor closer to the manifold.

@Chit_126 Год назад

How do you install to work with HP Tuners?

@Boostededdy 4 года назад

Question, what did you end up doing with all the other wires that were just left there?

@gmckid9166 3 года назад

I know I’m super late on this but I just figure out all my passwords again. I never ended up hooking them up. I was told it could be wired into the OBD2 port but no one ever told me how it could be done

@cbr1thou 4 года назад

Your clamps are leaking, get 3" clamps , dynomax on Amazon and copper rtv, or weld it and weld in v clamps

@54inches Год назад

On your truck, you need to install the Wideband install as close to the front as possible.

@dscracing0260 4 года назад

Did you calibrate the sensor ?

@RyanPowell887 3 года назад

How many engine grounds are you runnin

@gmckid9166 3 года назад

I have a body ground that comes off the back of the block, then there’s the one on the driver side under the head, and lastly the one that goes behind the front bumper. Those are just the factory grounds, I haven’t added any extras into it