2007-2011 Honda CRV Lower Control Arm Replacement DIY

Подписаться 54 тыс.

Просмотров 22 тыс.

50% 1

Here's how to replace the lower control arm on a 2007-2011 Honda CRV.
Driver side control arm: amzn.to/3M2GsJB
Passenger side control arm: amzn.to/3NORzqP
Ball joint separator: amzn.to/429ijXm
Ratcheting wrenches: amzn.to/42uMp7n
Swivel socket: amzn.to/3Ly2J0s
Impact wrench: amzn.to/3LEsa0k
Impact socket set: amzn.to/42dWENL
Torque wrench: amzn.to/3nzoCEL
Wire brushes: amzn.to/3VCdiEl
Threadlocker: amzn.to/3M4wnMr
Gloves: amzn.to/3nx8TpM
#ad

Опубликовано:

15 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 12

@MrRangerZr1 Год назад

Parts & tools listed below: Driver side control arm: amzn.to/3M2GsJB Passenger side control arm: amzn.to/3NORzqP Ball joint separator: amzn.to/429ijXm Ratcheting wrenches: amzn.to/42uMp7n Swivel socket: amzn.to/3Ly2J0s Impact wrench: amzn.to/3LEsa0k Impact socket set: amzn.to/42dWENL Torque wrench: amzn.to/3nzoCEL Wire brushes: amzn.to/3VCdiEl Threadlocker: amzn.to/3M4wnMr Gloves: amzn.to/3nx8TpM #ad

@Ilyaselho Год назад

I can change anything on my car watching just your videos lol thanks

@luisbalderrama8145 16 дней назад

Dude this is an excellent video! With the torque specs and everything. You're a saint. Thank you!

@osmanespinoza8697 Год назад

God bless, peace and love be upon you, your family and your friends Mr. Ranger. Can you do a 2018 Nissan Pathfinder SL 2 WD/ 4 WD on how to replace break pads, rotors, ABS sensors front/rear, spark plugs, water pump, timing belt, TPM, and power steering belt?

@stevef8993 Год назад

Thanks for the straightforward video. Why did you need to change the control arms, rust, bent? Also, how did you determine what the ride height should be to torque the castle nut? Did you measure it before you lifted the car?

@MrRangerZr1 Год назад

The bushings were torn on this car. Jack up the control arm until that side of the car barely lifts off the jack stand.

@clavin162 Год назад

@@MrRangerZr1 how is the Amazon part going strong??

@MrRangerZr1 Год назад

@@clavin162 Yep

@EsenbekAliev_ 11 месяцев назад

can you show more of that Odyssey on your page ? tesla wheels, lowered, headlight retrofit.. more pics and details?

@MrRedHotChiliMan 3 месяца назад

What’s the jack method you used here? Is the suspension under load or just hanging? I know you jacked up the arm to ride height to torque the ball joint bolt, but did you have the jack there when installing and torquing the other bolts as well? Thanks I’m advance, I have an 07 CRV as well and your videos are super helpful.

@MrRangerZr1 3 месяца назад

For suspension bolts, you want to tighten the bolts in the position the car will be on the ground, so you have to jack it up till it just comes off the jack stand.

@MrRedHotChiliMan 23 часа назад

@@MrRangerZr1I had another question. I noticed you used moog control arms. I was going to replace my tie rod ends with moog as well. The ends came with a couple regular looking washers included, do you have any clue where the washers are supposed to get installed. Mine in an 07 made in Japan. No washers on the current OE tie rod ends.