2012 Jeep Grand Cherokee Headlight Swap 

Hi, Hill, we would like to send to Hill to review our LED bulb too, would you mind to email me? Email: mark@wplamps.com

Do you manufacture a model that has amber side markers that comply with US S.A.E regulations?

What's the status on the sealing issues? Any resolution to this problem?

Win Power, can you please make this available plug and play for a 11'-13' Grand Cherokee with halogen. Right now most need a custom harness. Thanks,

sure we can make! but we don't have US GC in China. so would please do me a favor? we need to know your orginal headlight wring detail with photos(which wiring for what function. like, what wiring for turning, what wiring for Hight beam and so on). and please kindly email me at: mark@wplamps.com

E M- I was looking for these on eBay but I couldn't find them. Do you mind telling me what you searched or the link I would greatly appreciate it. 😊

www.amazon.com/dp/B01N0M7J52/ref=cm_sw_r_cp_ep_dp_u.Iqyb1E7SS91

www.ebay.com/itm/151767897489?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT

no problem, thanks for watching

I don't think you need to put the amber reflective tape in, I don't think it is a requirement. The headlights come sealed but they are not sealed the best.

Did you figure it out?

GlorybetoGOD7 I can help you out with the install, I also can give you 10% off the purchase of the headlights email me at iDriveSRTWK2@gmail.com

How did you figure it out??

Javi Fregoso email me at idrivesrtwk2@gmail.com if you want to buy a set

Nor does it lack that automatic regulation that is imperceptible I just mounted that headlights illuminate the road in high and low better than the Originals if the help of that regulatio

Thomas how did the auto leveling work out? I'm about to purchase but don't want to give up the auto leveling function.

Never mind. My wire taps weren't clamped all the way down. I'm now having an issue with my HID bulb not powering on or my ballast working on the driver side. I think it may have something to do with the Low Beam connector. The win power side for the low beam only has two prongs and a 3rd prong that is broken off at the base of the receptor.

Sorry I am not sure if it will work for none HID headlights. I think the connector may be different.

The new headlights have a automatic leveling motor but the connector and wiring on the motor is different then the factory. As of right now it is not possible to connect the leveling motor. Its not a huge problem. The headlights will just stay in a locked position.

Hey Mike does your headlight have 4 connectors or 5 like in the video?

@@chenderek8589 I figured it out somehow moisture got in the lens & burnt out the low beam lights. & there was a bad connection in the wireing connection that made the drl go out.

Yoskel Lopez Same here, you figure it out?

Yoskel Lopez Yeah I have the same issue, did you manage to make it work?

Hey man, Same problem with me. I have a 2012 JGC Overland Summit. A guy said that I need to check the polarity on all three wires on the driver side connector. then run an additional ground wire into that connector and or light wire. not really sure how to do it though I'm not an electrician. Send me a PM and we can discuss it more.

I would use LED. The size is H7. Winpower also makes LED bulb. Here is there link www.amazon.com/RCP-Headlight-Aluminium-Waterproof-Adjustable/dp/B01LVXMSIA

Actually, it's just a tip to put a seal on them ... but you should not need to add anything to a new article ... you should write to the seller and make the claim to see what solution he gives you.

This is what I was told. "Hi, it will dry itself. this is the design of the headlight, beacuse of the HID is very heat. It will dry in several hours when you turn on your headlight or in few days. no need to worry about this, thanks" What a joke. I'm just going to take them off and see if I can find the leak and add more sealant to the whole thing.

I recommend that when you lower the headlights to put more sealant do it on a hot sunny day where there is no moisture in the environment to see if it works. That's what I did.

My first install was on a very hot sunny day. Prep work was done inside and installed in garage. I took lights off again 3 days ago and went to town using almost a whole tube of the Permatex Clear RTV Sealant. Went over all the previous areas, around every plug, wires, basically anything that went inside the housing. This time I also used it to adhere the rubber covers and even around the outside seam. Used extra to fill in/build up a few spots I noticed where water may hold and seep in. I let it cure for 24 hours before installing and car has been sitting in garage since and today will be first time out. Its very humid and hot with scattered rain for the next few days. If its able to fogs up even in the slightest way I will have absolutely no clue where or how it would even be possible. I'll update once I've driven through some decent rain and has set outside in the humidity.

Update... Had decent storms today. Didn't really drive much in the rain it mainly just set outside. When I got home I checked and they both still fogged up... I mean WTF! It wasn't near as bad this time as it only covered the turn signal and along the bottom, but it still makes the lights look like sh*t and makes it dangerous when people cant really see my turn signal. Could the moisture actually be getting through the connections? I'm 99.99% sure I have sealed everywhere else. At this point I really couldn't be any more disappointed in them.

😂😂😂😂😂😂😂😂😂😂😂😂. They are always on as long as the car is on

How did it go? I have the same car just a year older overland model

I would like that info too

Protuninglab, they have em for 348$

I am wondering the same

Can you send me an email @ Robert.joseph.gale@gmail.com Thanks

Rob G sent u a email

politisht I can help you out with the install, I also can give you 10% off the purchase of the headlights email me at iDriveSRTWK2@gmail.com

I can help you out with the install, I also can give you 10% off the purchase of the headlights email me at iDriveSRTWK2@gmail.com

I can help you out with the install, I also can give you 10% off the purchase of the headlights email me at iDriveSRTWK2@gmail.com

I also want purchase have 2012 grand Cherokee overland 5.7

Loving the lights, still working great. no issues with fogging

Amazon