2013 - 2020 Ford Fusion Amp and Sub Install

Подписаться 134 тыс.

Просмотров 93 тыс.

50% 1

Parts used linked in the description below!
Watch a full tutorial as a 2020 Ford Fusion will have an amplifier and subwoofers installed to the factory radio. Note this Fusion has been equipped with the factory Ford Sony amplified sound system which will be retained with this install.
This video applies to Ford Fusion models for years 2013, 2014, 2015, 2016, 2017, 2018, 2019, and 2020. This video also includes amplifier wiring, amp installation and testing.
Click here to see how to set your gains on your amplifier!
• How To Set The Gains O...
If you have any questions, leave a comment below! Be sure to like and subscribe!
Parts used in this install (Amazon Associate Paid Links):
*Skar Audio Loaded 12" SDR Enclosure: amzn.to/3xGDj8f
*Skar RP-1200.1D Mono Amplifier: amzn.to/3sTr73b
*Skar OFC 4 Gauge Amplifier Wiring Kit: amzn.to/3zIWXT2
*Pac Audio Line Out Converter: amzn.to/33lRh5u
Disclosure: As an Amazon Associate I earn from qualifying purchases

Опубликовано:

6 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 178

@ProvoBeastAudio 2 года назад

Parts used linked in the description of the video!

@samueltownes6494 2 года назад

How much will it run for the whole set you have in this video

@ProvoBeastAudio 2 года назад

@@samueltownes6494 Amazon will have those current prices, and install will vary based on the shop you use. You can do it yourself to save on labor and use this video as a guide. Links in description

@MrXlopez05 2 года назад

Hello, I just got a brand new aftermarket amplifier installed in my 2018 Ford Fusion Titanium. The one that has the Sony Surround System with a center channel and a subwoofer. I also got a DSP installed as well. After I got these two things installed, when I went to the sound settings, it would not let me Put the sound in stereo and it is stuck in surround. The speed compensated volume also cannot be changed. I prefer stereo over surround and I was wondering how do I fix this problem and what should I do? Thanks.

@thisguysnameismatt4460 Год назад

I have watched many vids on installs in fusions. Passing wires thru the firewall is much easier using the big sqare grommet (edited location as i went out and re -looked at it) its to the left of the steering column near the floor. Where the carpet meets some firewall insulation, pull the insulation up, (edit stops here)Its about a 4 or 5 inch square and pops right out. Plenty of room to run wires. I found it when i installed my fog lights and DRLs that i toggled hot from the battery. Just pull the carpet down a little and its right there, cant miss it. Good vid tho.

@tkg565 6 месяцев назад

I’m having a hard time finding this, could you help me out a little?

@thisguysnameismatt4460 6 месяцев назад

@@tkg565 it should be right there as desribed.... not sure if they did diffrent on other years... mines a 2013. I'll see if i can take a pic. I just recenrly (finally) put a stereo in and ran my power wire thru it.

@thisguysnameismatt4460 6 месяцев назад

@@tkg565 ru-vid.comb0Bz2nN-c_c?feature=shared

@thisguysnameismatt4460 6 месяцев назад

@@tkg565 sorry, i kept forgetting to do this, hope this helps.

@Chippy363636 5 месяцев назад

For those who may have had this happen. I tapped into the wire mentioned on this video in my 16 Titanium and the wire was for my rear backup sensors. May be because of my line out converter but it caused them to disable and a warning came up on my screen. Otherwise Great video!

@xavierjohnson4999 2 месяца назад

How did you fix this?

@Chippy363636 Месяц назад

@@xavierjohnson4999 Wired it direct to the cigarette lighter and tapped into the positive. Ran the wire with my sub woofer bass controller up under the climate control buttons. Technically you can just wire it up to the positive on the subwoofer but to play it safe I ran it to the cigarette lighter.

@ErickWright 8 месяцев назад

Those wires look they really clean

@sevaslee4865 Год назад

Just save hella money with this video

@phonkushomonkulus8358 Год назад

I followed step by step and it works almost perfect. Only thing is that it shuts off when the trunk closes. Line out converter is powered on the same yellow-red wire. Not sure what to do

@ProvoBeastAudio Год назад

Power your LOC instead off of the power and ground terminals of the amp, or at the fuse box.

@robbyeagan7671 Год назад

@@ProvoBeastAudiomine is doing the same thing and can’t figure it out, and I’m not quite understanding what you mean in this comment? A little more help would be appreciated!

@Nargantous 10 месяцев назад

Run your LOC power wire into the amp with the main power wire coming from the battery that’s what I have done before with success

@keylinbrown9983 5 месяцев назад

Same issue but when I run the constant with the power straight to the amp it doesn’t shut off with the car

@ZakimboBlue 2 месяца назад

Thanks im doing this

@Christop775 7 месяцев назад

Was the yellow wire you tapped into for the LOC the parking sensor wiring?

@kingofta99 2 года назад

Any tips to do this from the rear door speakers?

@jus10foote 2 года назад

If you pull the trim on the B pillar(between front and rear door) the wiring will be there for the rear door speakers. If you take off the rear door panels and look at the speakers, you can see exactly what color the wires are that you will tap into.

@newbie_nugs 2 месяца назад

I have the fifteen titanium. So instead of going to the 6x9s. I would be going to the amp for thr single subwoofer. Can i still use this line output. I like the remote option right there. If not i think i can do an add a fuse to my truck fuse box instead of running up front

@lewissmith234 Год назад

Have you ever done something like this on a 2010~2012 fusion??

@jonahhenry5695 2 года назад

would you mind explaining the B-pillar alternate install? i purchased the stuff not realizing i didnt have the 6x9's

@ProvoBeastAudio 2 года назад

Pull off the B-pillar cover, and locate the wiring that feeds into the rear door. In that bundle of wiring, you will find a twisted wire pair which is your speaker leads. Here are those wire colors: Right Rear + Brown/white Right Rear - Brown/Blue Left Rear + White/green Left Rear - Brown/Yellow

@Beazta Год назад

You teach how to tap into these wires

@JD-ym2hg Год назад

@@ProvoBeastAudio hey great video it’s going to help a ton with a sub install I’m about to do, I was just wondering if I’m only installing one subwoofer, do I need to tap both rear speakers? Or just one.

@ProvoBeastAudio Год назад

@@JD-ym2hg Technically, being a mono amp., you can get away with just tapping the LOC both channels into one speaker. The only argument to that would be if any audio being played has bass frequencies coming out of different speakers, you may have an issue there.

@JD-ym2hg Год назад

@@ProvoBeastAudio thanks sm for the reply, and that’s what I figured. I did some research and apparently it’s not uncommon for people to just use a Y splitter to send signal to a single subwoofer. Btw this video has been so helpful. 🙏

@summershores8957 2 месяца назад

My 2016 Ford Fusion Titanium doesn’t have a yellow and red wire. But it has a yellow/orange and yellow/green..

@wess6658 Год назад

Yo how filtered is the signal at the rear 6x9's? What frequency is subsonic (lpf) and what frequency is high-pass? I know this is why they make dsp blah-blah-blah but seriously where is a full-range signal? Why did the carmakers delete a full-signal that we can tap into? Baffles me....

@ProperScope Год назад

Is there different 2 yellow and red 12 volt wires go for converter?

@billsmith6325 8 месяцев назад

I have a 2018 taurus SEL and was wondering if I could do the same with my LOC in my trunk or do I have to go in behind the infotainment console?

@user-mm4hd2qm6t Год назад

I have a 2014 which has the speakers in the rear doors not in the back in trunk. How do I tap into those?

@jhermelmorris3783 7 месяцев назад

Hey did you ever figure it out

@puredaylite559 Год назад

Not sure if anybody knows will this work on a 2017 Ford fusion with the remote wire for some reason mines not working

@richardnorris8377 Год назад

I have a 2013 ford fusion se without the 6x9's since I don't have those wires to tap into what would I tap those wires to

@ProvoBeastAudio Год назад

I'd tap into the rear door speaker B pillar wire locations.

@Pete.across.the.street Год назад

Why no mounting plate? Why didn't you loom all the wire? What did you do to prevent the wire being pinched by the seat?

@tryroger 4 месяца назад

Are the subwoofers included with the box on the link

@vontaadams6013 4 месяца назад

I have a 2020 ford fusion se and I don’t have back speakers so idk where to put the converter

@iCripL Год назад

I'm having a problem where the amp constantly has the red light on by the "protection" text. Do you think I may need a new amp. I did it almost exactly as you did in the video. Got it to work for a whole 5 minutes too by moving my ground to a different spot, but anytime I turned the volume up slightly it would just go back into protect mode. Haven't been able to replicate what happened since.

@TheBlueDemon00 Год назад

Have you double checked your remote wire connection or the fuse on your power cable?

@iCripL Год назад

@@TheBlueDemon00 I figured it out, it was a faulty amp. Skar sent me a new one.

@prestonklug7792 Год назад

Will this work on a 2012 ford fusion and just say down the road if I want to install a aftermarket radio will this all still work the same or will the subs and amp not work anymore once I install that radio?

@jonlorenzo5992 2 года назад

Other than the battery being located in the rear on an 18 hybrid same Sony set up with the factory 6x9s is the wiring any difference I imagine it'd be a significantly shorter and you wouldn't have to fight with the firewall or removing all that crap to hide the wiring because it's already in the trunk

@ny2bama Год назад

Did you get installed? Any tips?

@yaboyruben2343 2 года назад

Does anyone know if these same steps will apply to a fusion sel?? It has the 6x9s in the back but based off the research I did it's what's known as a premium audio system and not the Sony one.

@ProvoBeastAudio 2 года назад

Yep, will be the same process!

@patrickball5033 2 года назад

I have having a problem trying to find where to pull the battery wire through.

@thisistheway9174 2 года назад

Same. I am running 0 gauge ofc by skar.

@chriscarlsonii9466 Год назад

Cannot seem to get subs to have power, the amp does and so does the LP device, my stock 6x9 are working still with everything soddered idk what to do

@babydro108 2 года назад

you think I could fit 0 gauge through the same entry point you use for the 4 gauge. thank you

@devildog1534 Год назад

Ever figure it out. I’m thinking about running 0 gauge wire through mine.

@BrianWaller-qe7gr Год назад

I’ve watch many of his videos I don’t ever recall him installing anything other than 4 gauge. Many installers don’t want to install higher wattage systems because they are intimidated. Funny thing is it’s the exact same process just dealing with bigger wires and higher fuse ratings

@Meddawg799 Год назад

I just hooked all this up on my son’s 19 FORD FUSION TITANIUM with the Sony stereo yesterday. Today his battery ended up being dead. I want to make sure I didn’t wire something wrong. I attached the yellow wire to the constant yellow/red wire and it looks like the light was staying on at the line out converter even after shutting the car off. I’m hoping that’s not draining the battery. The battery probably needs replaced but now I’m worried it’s what I did.

@ProvoBeastAudio Год назад

The line out converter used should be connected to constant power as it will turn on your amp as soon as the vehicle wakes up. It will remain on, even after shutting the vehicle down until the electrical system "goes to sleep". Very common on late model Fords.

@jessiemock1128 4 месяца назад

Will this work with the hybrid as well ?

@samueltownes6494 2 года назад

The whole setup that you have in this video how much will that run me

@ProvoBeastAudio 2 года назад

All linked in description for current price.

@gabrielsabutis4864 2 года назад

My car is a 2018 and my deck speaker wires are different colors. Do you happen to know if I can tell the difference without a meter

@paco.taco.flaco28 2 года назад

It would be really easy with a voltmeter.

@RyanAnderson-gh3sh 5 месяцев назад

How do you adjust the bass for different music?

@ProvoBeastAudio 5 месяцев назад

The Skar amp includes a bass knob.

@jayayala2045 Год назад

Is there any specific amplifier for the a 2014 ford fusion or I can use any amp ??

@samuelcalero5925 Год назад

It’s any amp as long as it doesn’t dish out more power than the speakers need

@Addy376 2 года назад

ive watch this video 36 times still don't understand we're the converter speaker wires hook to witch ford wires

@ProvoBeastAudio 2 года назад

Well, @9:44 we show you how to extend the speaker wire inputs so they can reach the rear deck speakers, and @11:19 we show you how we ran them up to the rear deck speakers, @11:28 we show you how they tie into the rear deck speakers left channel, and @11:51, the right deck speaker channel. Now sure how in your 36 times watching you would miss the second half of the video??

@paco.taco.flaco28 2 года назад

I grabbed the 12v from the same wire as in your video but it won’t turn on my amp. I do have 12v at the amp but my remote from the LOC is not 12. Could the LOC be bad?

@sniyps1444 2 года назад

Did you ever figure out your problem with the rem not having 12v?

@paco.taco.flaco28 2 года назад

@@sniyps1444 I did. I’m not sure if it’s bc I have the 2020 SEL trim but I couldn’t grab 12V just like he did on the video. I had to grab 12V from the fuse box in the drivers footwell. I also noticed if I wired it like he did, my backup camera and sensors would not work correctly.

@freddymendez4698 2 года назад

@@paco.taco.flaco28 Im having the same issue, wires are connected to the same ones as in the video but no power at amp. Can you verify when the loc is properly hooked up does the light on it turn on?

@paco.taco.flaco28 2 года назад

@@freddymendez4698 I had the same issue getting power for the amp. So I grabbed power from the fuse panel under the drivers dashboard and ran it all the way back to the amp. Everything else worked. My speaker wires were different color than the one in the video but all I did was find out which wire was positive and which one was negative.

@freddymendez4698 2 года назад

@@paco.taco.flaco28 where exactly in the fuse box did you tap into if you don’t mind helping out!

@gregtaylor8727 2 года назад

Have u solved the active noise cancellation problem yet?

@gymnabetic382 Год назад

If you're talking about a constant firing of the subs, all you need to do in unhook a microphone connection above the rear passengers. Took me weeks to find the solution but only takes 30 seconds to fix.

@m0ren0140 6 месяцев назад

I have a ford edge and I disconnected all speakers and still didn’t fix

@GarrisonSnyder Год назад

quick question on this install. i have a 2017 ford fusion sport with the sony radio. I tapped into the yellow red wire for power on the line in like you suggested but can not get power to my line it, do you have any advice?

@ProvoBeastAudio Год назад

Just relocate the power and ground of the Pac module to rob power and ground off the amplifier and that should fix your issue.

@GarrisonSnyder Год назад

@@ProvoBeastAudio will it turn the amp of when i turn the key off?

@noahlittlefield6890 Год назад

@@ProvoBeastAudioso that's the yellow LOC wire in the amps battery terminal, and the black LOC wire in the amps grnd terminal, right? Cuz that's how I have it wired and I have no power to my sub still. Do I have to use the brown wire off the LOC?

@zacharymartinez6489 Год назад

I can’t even find the yellow with red on it back there any other suggestions?

@zacharymartinez6489 Год назад

@user-bx8dx8mf3q did you even figure it out?

@SierraRomero-d3v 8 месяцев назад

I have a 2013 ford fusion hybrid and I have back door speakers we connected everything and it pounds but when I go to drive and I accelerate the gas pedal it makes a really loud humming sound in my subs what could that be we’ve tried to figure it out but we can’t find the problem why it’s doing that??

@adamhawkins243 7 месяцев назад

It sounds like you may have a bad ground

@derekmetcalfe4630 2 года назад

I have a 2017 ford fusion titanium. same setup as the video. I bought the inline converter you used. I wired everything the exact same. I have power to my amp (pyramid classic 1000w) but nothing from the subwoof. (pioneer 12") what could the issue be?? I'm lost

@dillonwestgate1625 Год назад

lmao what was the problem? because this sounds like what im dealing with

@noahlittlefield6890 Год назад

Dudddee same hereee, amp has power but nothing to the sub 🤦🏻

@natelamb6170 Год назад

Check the remote wire voltage. Mine was running 4 volts, Needs 12 volts to turn amp on.

@iCripL Год назад

@@natelamb6170 How'd you get yours to run 12 volts? I'm running 4-6

@Cdunnak Год назад

Do you plug the harness back into the rear speakers after tapping into them?

@alexmadera4005 9 месяцев назад

Yes

@jackdoff3633 Год назад

can you still wire to the factory radio if you dont have the sony sound system, i have the non sony 8” system with 6 speakers

@rongilesjr2334 2 года назад

I have a 2013 Ford Fusion SE it doesn't have the 6×9's but I do want to upgrade my factory system I have already replaced the factory door speakers do you have any recommendations on what kind of 6×9's and subs will best fit in my car😁

@NATUREMAN360 2 года назад

I am doing the same. I bought a paid of JBL's 6 X 9 three way speakers from Best Buy to go in the rear deck and adding a 4 channel bridgeable amp to play them.

@meechwilliams5923 5 месяцев назад

What if I don’t have the 6x9 in the back deck but have the factory amp still where do I place the speaker wire to tap into the factory system

@ProvoBeastAudio 5 месяцев назад

B pillar speaker wire or at the radio. I also provide a T harness (non factory amplified trims) that prevents the need to manually tap into wiring: www.provobeast.com/product-page/2011-2020-ford-add-an-amplifier-t-harness

@eduardogerman2854 2 года назад

Can the 2 channel line converter be purchased at any local retail store

@ProvoBeastAudio 2 года назад

Walmart will have a few versions, sure.

@killer1245thug 9 месяцев назад

Have you done Ford Taurus?

@killer1245thug 9 месяцев назад

If not I’ll give you my Ford and parts lol

@jesusrubio4498 2 года назад

You didn't explain where to connect the remote wire to turn on the amplifier

@ProvoBeastAudio 2 года назад

To the remote turn on terminal on the amplifier.

@freedomordeath1216 11 месяцев назад

Thank you for this video! By chance could someone help me out, I ran my power and ground wire for my amp. I don’t have speakers in my rear deck. I know I need to run my speakers wire on the opposite side of my power wire. Should I splice in behind my 4” radio, the rear door speaker or tweeters? What color wires am I looking for?

@Aintnowayyy-c8x 8 месяцев назад

I’m having the same issue for placing my loc back there

@Mr.Towboater87 5 месяцев назад

What did you figure out

@freedomordeath1216 5 месяцев назад

@@Mr.Towboater87 I spliced behind the radio. I was worried about breaking the plastic trim removing it. But it came off nice and put back together nice.

@Mr.Towboater87 5 месяцев назад

What speakers did you tap into both rear speakers

@baconand3ggs 2 года назад

I have a 2014 with the 8” touchscreen. It has no rear 6x9s where would I want to connect the wires from the output converter that you connect to the 6x9s

@ProvoBeastAudio 2 года назад

You can go to the B-piller to tap into the rear door speakers as an alternative!

@juniorcates3343 Год назад

what would a shop typically charge for something like this? All the amps and subs i would provide

@alexsampson3579 Год назад

Best Buy charges around 150 for a basic install. Never go to actual shops because they will overcharge you by a MILE. The Best Buy that did mine did a phenomenal job and I’ve had my subs in working order for over 3 years. You just have to find the right guys for the right price 🤷‍♂️

@trxpbxy Год назад

@@alexsampson3579 false , just checked . $350 for basic install .

@haanstang648 2 года назад

Would the PAC audio line out converter be the right choice for my 2018 Lincoln MKZ with the stock revel audio system? Thanks in advance

@ProvoBeastAudio 2 года назад

Sure would be. That is linked in the description of the video!

@ethankramer1004 Год назад

I did this but used my rear door speakers because I do not have 6x9 and my amp goes into protection mode as soon as I turn the car on. Any help?

@ProvoBeastAudio Год назад

Sounds like you have a short somewhere. Hard to tell without seeing it in person! Check all your connections and wiring to the sub.

@kingdamian3393 2 года назад

LOC doesn’t come with remote wire. Is there a place where I can connect it?

@ProvoBeastAudio 2 года назад

Go to the fuse box, find a circuit that is only on when the vehicle accessory is on / running, and use an "Add-A-Circuit" to safely tap into that circuit.

@speederwill Год назад

Did you plug the factory 6x9s back in or do they have to stay disconnected

@ny2bama Год назад

Plug back in

@jonchowles21 2 года назад

When you take the signal from the 6x9’s do you lose the audio to the 6x9’s? I want to keep all my speakers and add a 10” sub. Is that possible?

@m3m3gamer53 2 года назад

you keep them as long as you use a t splice or make sure to sodder then correctly

@raffewittig6231 7 месяцев назад

everytime i shut the trunk i lose my subs they just go super quiet and i don’t know why pleas any ideas

@spencerharmon4012 5 месяцев назад

i saw another comment with the same issue. the creator told them to run the power under the same lug as the power to the amp

@jk262831 Год назад

I hooked up power for the line out converter to the exact yellow wire in the trunk and now my rear park assist is not available. any idea what could have happen.

@jk262831 Год назад

I may not have disconnected the battery is it possible I blew a fuse.

@ProvoBeastAudio Год назад

Yeah, check fuses. Sounds like a wiring issue to me.

@mathewdearinger2891 Год назад

@@ProvoBeastAudio i also hooked it up to this wire in my sons 2019 sel and his parking assist was not working and we did unhook the battery so i cut the wire and them started working again

@22kings5 Год назад

What are the factory speakers wire colors?

@bmgeaney1238 Год назад

How would i do it to a 2019 fushion with out the sony 6×9s in the back mine didnt come with them

@ProvoBeastAudio Год назад

Tap the line out converter to the speaker signal in the b-pillar covers.

@tcs124 2 года назад

Where do I get the zip tie anchors you used to hold the wires down

@ProvoBeastAudio 2 года назад

amzn.to/3OxLMnh

@margrettemcconnell 7 месяцев назад

Hello I’m reaching out to you guys cause I followed your video to hook up a subwoofer and amp in a 2018 Ford fusion. I purchased the Loc pro 7 and I hooked everything up as you did step by step in the video. I had no power light to the Loc pro 7 until I unhooked the remote wire from the loc and ran it to my fuse box under the hood. I have a red light now on the loc pro but still no sound through the sub. I tested the amp wires for power and their getting it bit nothings happening. How do I fix this?

@btookz Год назад

Did you hook back up the deck speakers

@ny2bama Год назад

Yes

@ayebaldhead5133 2 года назад

In which fuse location did you use to put your remote wire. Under the hood or under the dash. Also which fuse number was it and/or what does it control. Mine stays on and id like to have it activated when the key is on

@ProvoBeastAudio 2 года назад

We didn't tap into the fuse box for our remote as our line out converter provided the turn on trigger for our amplifier. This is why we used the Pac LP7-2.

@ayebaldhead5133 2 года назад

@@ProvoBeastAudio is that sold in stores or online only

@ProvoBeastAudio 2 года назад

@@ayebaldhead5133 Everything we used is linked in the description of the video.

@ProvoBeastAudio 2 года назад

@@ayebaldhead5133 We have ours linked in the description, but it can be picked up at your local audio shop or best buy.

@ayebaldhead5133 2 года назад

@@ProvoBeastAudio thanks bro

@longhair5978 Год назад

Too bad the guys with multi tool wouldn’t stop made it hard to watch with that racket going on in the background.

@tyronemorris1976 2 года назад

So you don't have to hook anything up to the factory stereo?

@ProvoBeastAudio 2 года назад

We did, just at the speakers in the rear deck, not at the radio.

@tyronemorris1976 2 года назад

You not located in Philly are you?

@leroylira8460 Год назад

Is it the same process for a 2018 ford focus SE ?

@ProvoBeastAudio Год назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-pAPyQU4a6AY.html

@hwbwijensin6616 Год назад

do you need to run the wires through the head unit? (as in disconnecting the whole head radio to connect wires in the inside of it and reconnecting it?) sorry for the bad explanation

@devildog1534 Год назад

Could a 15 inch skar prefab fit in the ford fusion?

@LushRR Год назад

Nope

@Kadashh 2 года назад

Does the 2019 headlights fit 2014 models ?

@thisistheway9174 2 года назад

No they don’t. 2013-2016 Fusion are the same but 2017-2020 Fusions are different.

@JimmyShit 2 года назад

aye man how did u mount the amp to the back of the seat isn’t that shit metal ???

@charliebryan7345 Год назад

They look like self-tapping screws

@jcarcr8 Год назад

Does the box itself have wires in it? Or just rca hooks up directly to the speaker inside the box?

@hippieish7330 2 года назад

Do you know if the 12v consistent is the same wire for a 2015 SE 2.5 model?

@hippieish7330 2 года назад

Anyone wondering the same, I just ended up going with the kicker LOC that takes signal from your speaker wire and turns it into a 12v! Has worked perfectly for me so far!

@herrbailey8277 2 года назад

Is there a difference between a "Factory Radio Amp Amplifier subwoofer Interface Wire Harness with Inline Converter" (amazon product), and the "LOC Pro Inline Output Converter" you are using? I have the Sony system. Would I need a bass restoration processor? Thanks.

@wyattrobison2379 Год назад

I have some questions

@ProvoBeastAudio Год назад

Shoot us a message on facebook and we can help out.

@margrettemcconnell 7 месяцев назад

@@ProvoBeastAudio Hello I’m reaching out to you guys cause I followed your video to hook up a subwoofer and amp in a 2018 Ford fusion. I purchased the Loc pro 7 and I hooked everything up as you did step by step in the video. I had no power light to the Loc pro 7 until I unhooked the remote wire from the loc and ran it to my fuse box under the hood. I have a red light now on the loc pro but still no sound through the sub. I tested the amp wires for power and their getting it bit nothings happening. How do I fix this?