Hey Tim I just used the nec cluster cable on 3 jetta's. I'm using vvdi2 almost the same process as abrites. The first 2 went perfect, the last one displays immobilizer on tge screen when installed back in the car. Any suggestions ? Jonathan
Hi Tim, great video. I've read the eeprom manually using a programmer, when I've done the service mode I've accidentally overwritten the original dump. Is there any way to repair eeprom dump ? Thanks
The only way I know of is to either use ODIS and reprogram, or read data from the ECU and build your own data into it.. Thats the reason we quit eproming these.... The easiest way I have done these when the data is lost, is write data from a like cluster, then pretend you are replacing the cluster.. Read the CS, MAC, PIN from the ECU, then manually type them in.. Sorry bud, I know exactly what you are looking at.. it's not fun..
Hey brother. Excellent tutorial, I'm curious where you found the chip layout diagrams for the various clusters. The ADC219 cable manual says there is more documentation on the AD website but I can't find it to save my life.
They come on a CD when you purchase the AbritesUSA NEC cluster cable kit... www.abritesusa.com/store#!/VW-NEC-Cluster-Set/p/134601930/category=34357291
Still just as confused as when first started watching video. How can we pull the pin / cs code since we don’t have a bench setup and would like to go to vehicle, add precoded key from dealer to vehicle? Any help greatly appreciated.
what part of the video confuses you?? If this confuses you, why are you trying to find the CS and pin code? If you are just adding a key with a working key, go to the car, turn car on with working key, then click on enter service mode, it will enter service mode, then click on add a key, put your dealer key in the programmer, it will add the key to the immo and then you are done.... This is aftermarket software that allows you to make and program a key from scratch... If you have a dealer key, you have to get the car into service mode to program the dealer key into the car, to do that with aftermarket software, you need to either have a working key, or use a bench setup, and hold the boot pin on the cluster and put in boot mode, then program the key.. Or if that confuses you, go to volkswagen and purchase ODIS, it's $1,000.00 a year for VW and $1,000.00 a year for Audi, then you can buy your keys from the delaer and just program them into the car with Odis...
@@bhimbieslocks8736 should... just remember, with micronas you have to take daughter board off the back of the case, and then put on mainboard, then pogo
I use ABRITES, you can find it at abritesusa.com It makes it rather easy to read the data from one and transfer it to another.... and if the original is gone, you can read the data from the ECU and get the other data from the car and input it and viola, your up and running
Hi, I got a 2016 Jetta premium 3D cluster (SW1009). I can’t find the pin-layout on the internet. Is there any info about this? Or can I use the old method with chip reading? Would love to hear from you! Thanks Tim!!
if you are looking at the blue plug on the back of the cluster, the end that is wider is pins 16 and 32, pins 31 and 32 are power, 29 is Can lo, 28 is Can hi, 16 is ground, 7 and 8 are the key coil.. and if you want to make a cable, OBD2 pins are pins 4 and 5 are ground, pin 6 is can hi, pin 14 is can lo, and pin 16 is positive..
@@timtracy9442 Sorry, I was trying to say where the ground pin/reset pin location is on this cluster. Tried some points on the back of the cluster, but I can’t enter service mode on this cluster. Older 2D/color cluster wasn’t a problem, by using service mode on bench.
WHICH CHIP IS IMMOBILIZER CHIP? I AM A REPAIR SHOP FIGHTING ONE OF THESE DUE TO BAD SCREEN AND TRYING TO SAVE CUSTOMER MONEY. AND TRYING TO USE A GOOD USED IPC
the chip that has the immo data is the 24C32 or 24C64 chip that is under the dials... Why wouldn't you just move data over using the cable? I have literaly done hundreds of clusters by putting on bench, read data from old, then read dat from new/used, then overwite the data.. you have immo data and coding data, if you move the immo data and the cluster is coded differently, you are going to have a blank cluster..
