2022 Runaway Rangerunner MODS Part 1

Подписаться 595

Просмотров 4,1 тыс.

50% 1

The Runaway Gang just got their Runaway Camper back home to North Carolina and we are already hard at work modifying it to meet our needs!
Removed ALL electrical wiring that runs underneath the camper and brought it ALL inside the camper!
Replaced the flimsy plastic license plate holder with and cool diamond cut metal one!
Added a couple of custom metal license plate frames for "Benfield" (our 2016 Subaru Outback) and "The Hideout" (Our 2022 Runaway Rangerunner Camper)!
Hope this helpful for ya!
There will a LOT more Runaway Camper MODDING videos to come so stay tuned!

Опубликовано:

27 июл 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 15

@oldschooldiy3240 Год назад

I respect your willingness to live on the edge....just in case you didn't know, several states have enacted laws about license plate frames which state "No part of any writing on any licensing plate may be covered, in part or in whole. This shall include any vehicle registered in this state, or any other state."! You can thank law enforcement for this....

@TheRunawayGang Год назад

Hey Old School! Thanks for the tip! I was completely unaware of that! Thanks for dropping by!

@coltallman854 Год назад

I see you are from NC. Me too! I'm looking to get me one of these spring of this coming year!

@TheRunawayGang Год назад

Hey Colt! Where in NC? We are thrilled with our little runaway! So glad ya stopped by!

@chroniclesofstuntbucket3522 Год назад

I don't consider the rubber license plate frame flimsy - it is that way on purpose so when you most assuredly hit your plate on something it just deflects out of the way.

@TheRunawayGang Год назад

Hey thanks for dropping by and sharing your thoughts! Much appreciated! Always good to have different takes on the same thing! You make a valid point!

@chivasmom2024 Год назад

Nice mods! Thank you for showing the wiring detail, very helpful. I plan to order mine without that rear strip, thus avoiding all the holes in the bottom of the camper. It is in an odd location anyway, and not needed. Do you find the height of the camper to be too short? I think an extra 6" would make a huge difference in comfort.

@TheRunawayGang Год назад

Super glad the video was helpful to ya! For the height is perfectly fine! I am 5’ 10” and I can comfortably sit on the bed without my head hitting the ceiling. Our bed top is approximately 13” from the floor of the camper and then my weight would compress that down to probably 10” or so if that helps ya any! I actually prefer the lower profile for ease of setup and towing.

@chivasmom2024 Год назад

@@TheRunawayGang That information is very helpful, thank you. I am trying to decide between the smaller Coolcamp, or the Rouser! Ideal would be 5Wx8Lx5H but doubt they will ever make that size.

@TheRunawayGang Год назад

@@chivasmom2024 Glad that was helpful to ya! Sounds like maybe the rouser might suit ya better then. No concerns about height with that one! Blessings!

@stevelindsay3858 Год назад

Did this mod violate your warranty?

@zacharyhunter6408 Год назад

What did you use to remove the range runner sticker?

@TheRunawayGang Год назад

Ha ha ha! I actually tried several things to get the sticky off. The stickers themselves came off ok but left a sticky residue behind. Between isopropyl alcohol and goof off and some elbow grease I got it off!

@zacharyhunter6408 Год назад

@@TheRunawayGang thanks. I’m about to attempt it with mine

@TheRunawayGang Год назад

Go for it!