234hp 8th gen Honda Civic FD R18 Turbo Reflash tuned using 100% Stock N/A ECU without extra tools

Подписаться 389

Просмотров 15 тыс.

50% 1

Stock ECU Reverse Engineering and Reflash tuned by XGN Performance
- Full Speed Density Conversion
234hp 274Nm
Car built by TstepsRacingShop
- IHF55 Turbo
- Stock crankshaft
- Forged rods
- Honda OEM R20 pistons
- Chinesium Billet IHF55 Turbo
- Chinesium 650cc Injectors
- Chinesium Triple Plate Clutch
- Stock fuel system
- TstepRacingShop turbo and exhaust system
Running at Lambda=0.75 or 11.0:1 AFR for maximum safety for cast-iron pistons
Considerate ignition timing with full knock control
Such a fun car!
Thanks for watching!

Опубликовано:

30 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 110

@erwinsm10 Месяц назад

What ??? It can't be done !! But you did it !! You are the tuning wizard .

@XGNPerformance Месяц назад

🙏🙏🙏🤝🤝🤝

@BulliKid Год назад

Nice build!! I also run stock 02 sensor and I run at 10.5 afr wide open throttle. Do you suggest even lower afr ? Check out my turbo r18 in America!

@XGNPerformance 11 месяцев назад

Hi Stock O2 Sensor in these cars always report richer than the mixture actually is when the mixture is rich, they are ok when it's not as rich. That's why I said I did it rich using stock sensor, to avoid going too lean. Then I refined the tune with a wideband later.

@BulliKid 11 месяцев назад

@@XGNPerformance what afr are you targeting in boost now with wideband? And is your factory o2 still saying 10.14 at wot

@XGNPerformance 11 месяцев назад

@@BulliKidFactory O2 says 10.14, Wideband says 11.5-11.0:1 at 10psi/0.6bar and 10.8-10.5:1 at 15psi/1bar

@justintso 11 месяцев назад

Hey man! Stumbled upon this video, it really inspired me to Turbo my R18. I love my 8th gen non-si civic... I want it to live forever. It is also my first car. I have just one dumb question... does the R18 Turbo need higher octane fuel? or can still run 87? That closing remark really hits man, I am so glad that you are tuning cars and it makes you happy!!!

@XGNPerformance 11 месяцев назад

Hey! Thank you for watching and your kind words! I really appreciate it! Regarding fuel, minimum fuel recommended will be oct91(ron95) for the boost stock sensor can prrovide, which is around 6-10psi with considerate timing.

@ancientsociety653 Год назад

Unreal! Someone who did it right! the FD2 made 222 HP! What an accomplishment! I would love to see the R18's get some love.

@XGNPerformance Год назад

Thank you for your kind words! And I fully agree 100%! R series engines need some love too!

@shadf7902 11 месяцев назад

Huh? They can do 300whp stock internals

@XGNPerformance 11 месяцев назад

@@shadf7902 They can do more than that. But that's not what he meant.

@Thevqboy3.7 2 месяца назад

I will do the same set up on mine thanks bro to opening up my eyes 🤝 big fan from QC MTL

@BulliKid 5 месяцев назад

Have you used or Heard of people using kingtec racing rods and pistons?

@XGNPerformance 5 месяцев назад

This car has KingTec rods

@BulliKid 5 месяцев назад

@@XGNPerformance what’s your feedback from them?! I just got their R18 forged rod and piston kit.

@AtoriKushina 18 дней назад

did you ever end up sleeving? or was it just the OEM pistons

@XGNPerformance 18 дней назад

Stock sleeves and stock pistons are fine for 15psi with conservative tuning

@bpturbo27 Год назад

Love what you did brother , you're humble and very there for the people, as 4 your English I understood everything you said and so will the world , we need more information on how much it costs and the supporting mods

@XGNPerformance Год назад

Thank you for your kind words and support my brother 🥰

@nissanv6TT 5 месяцев назад

using WinOLS for tuning is crazy. Very powerful utility in the right hands though. Glad I got haltech working on my b18 lol.

@hazimkhairuddin4510 Месяц назад

La ingatkan melayu

@TET2005 2 дня назад

Way to go... the car needs a good wash though.

@delacruzjeremyc.70 8 месяцев назад

That’s unreal 🔥, do you have partners here in the Philippines?

@XGNPerformance 8 месяцев назад

Thanks I have one in Cebu, and could do more in Manila if needed.

@Queso305 8 месяцев назад

Your English is great! Your tuning seems good too!

@XGNPerformance 8 месяцев назад

Thanks for the support!

@carlostossas9024 2 месяца назад

Can you tune a factory Lexus ecu ?

@XGNPerformance 2 месяца назад

Can do many of them, but not all.

@adonaydelgado5839 6 месяцев назад

What kind of turbo manifold are you using nice build

@XGNPerformance 6 месяцев назад

Thanks! Custom made locally by TstepsRacingShop!

@Luisangelangulo2 11 месяцев назад

I made 240 whp on my 8th gen civic si full bolt ons on E85 tuned all motor k24 swapped on mine

@XGNPerformance 11 месяцев назад

Congrats, that makes about the same as our Toyota VIOS when it had K24A2 on E85. Nice power you got.

@Motofried 9 месяцев назад

What other mods are you running I made 253 on my k24 swapped 8th gen on 93.

@Luisangelangulo2 9 месяцев назад

@@Motofried I’m trying to buy supercharger for my car to make better numbers

@tanavatborisud437 7 месяцев назад

สุดยอดมากครับพี่ชาย ผมติดตามพี่อยู่ครับ หวังว่า สักวันจะได้เอารถไปทำกับอู่พี่ครับ

@antonysnoop Месяц назад

You’re the best my master! Saludos desde Honduras!

@CheatsCustoms 17 дней назад

Hello sir ! Great work I am doing somewhat of a similar setup as well Any way to get in touch with you regarding the tune Thank you

@XGNPerformance 12 дней назад

@@CheatsCustoms Hi! Contact me on Whatsapp at +66864099800

@promatic3871 Месяц назад

Stock internal and stock block and stroke?

@mohamadfaiz8484 10 месяцев назад

I got 247.96 hp 29.68 torque with stock engine and td05 stock turbo ✌🏽✌🏽

@XGNPerformance 10 месяцев назад

Congrats on your success

@josephbarlow8937 6 месяцев назад

What turbo you used

@WorasitRakthiangtam Месяц назад

Definitely be one of yur big fans kub

@kutlee2009 Год назад

Isn't r20 pistons aluminium? What is advantage over r18 pistons?

@ninovojnovski3991 Год назад

Can it be done online? I’m loving it 🚀😍 Respect from Macedonia 🇲🇰

@XGNPerformance Год назад

Thank you for your kind words Yes, online tuning can be done. We just gotta talk about the specifics. My Whatsapp is +66864099800

@dinukalakmal3155 Год назад

this is an one of my dream builds

@АлексейПерминов-н4и Год назад

Fuel consumption increased in comparison with R18 atmo? I mean cruise load.

@XGNPerformance Год назад

If you use the same power, there would be almost no change in fuel consumption. And better responsiveness, because we tuned knock limited ignition timing to suite the fuel well. So the car will get better ignition timing in all range, thus better efficiency.

@paulo..ferreira Год назад

Totally awesome!!! Keep up the amazing work you do!! 👏👏👏

@XGNPerformance Год назад

Thank you my friend Paulo

@rickyboostedhonda27 11 месяцев назад

I have a 2006 r18 automatic. How did you tune it in a stock ECU ? What did you use

@XGNPerformance 11 месяцев назад

WinOLS for editing PCMflash for reading and writing Lots of things need to be done. I do my own firmware reverse engineering deep down to Assembly codes. That's how I'm able to do these.

@fa1_z 11 месяцев назад

Subscribed! Love this kind of stuff! Canada here - could this be done with automatic transmission? Could I safely boost the car and start to build the rest as I go? Or should I start by swapping out pistons and whatnot? Great content man - love what you’re doing! Would love a breakdown video of everything you’ve done so far :)

@XGNPerformance 11 месяцев назад

Thanks! Appreciate the kind words! Yes, you can do 5-7psi with automatic fine. This car was also boosted with automatic + stock internals before.

@josephbarlow8937 6 месяцев назад

Where you get her vacuum form the pvc

@MrBluePoochyena Год назад

The Wizard of ECU's doing their job ;P

@RollingRoadEFI Год назад

Asian Einstein at it again 🙏

@XGNPerformance Год назад

Thank you my friend

@JoacoColombo 7 месяцев назад

Hello!! How did you deal with the MAP and MAF sensors?

@XGNPerformance 7 месяцев назад

MAF is deleted and converted to Speed Density with new tuning tables I created. MAP sensor is 4bar from Toyota Turbo Diesel, rescaled correctly, can read boost directly from obd2.

@bspbrandonsweatphotography7945 11 месяцев назад

Thanks bro inspiration for me to finally go in and get my turbo build started I’m just running cold air and catless at the moment and I am looking to pull more power from this block thanks for showing the potential and big ups from the us to Bangkok homie keep ripping tec (vtec) my man‼️‼️‼️💥🔥

@XGNPerformance 11 месяцев назад

Let's go!!! I'm just glad what I do means something to others. I really am. I wish you the best and success and your project! Honda forever! Thank you for watching and thank you for your kind words!

@shawnmarques7117 11 месяцев назад

K20/k24 here 240 hp 184 torque.

@XGNPerformance 11 месяцев назад

Good power, we made similar power with our Toyota when it had K24+20 before we remove it for a J35.

@Motofried 9 месяцев назад

I thought you’de make more than that with a k20/k24 setup my k24 swapped engine makes 253 on 93 .

@XGNPerformance 9 месяцев назад

@javielo1374 It's also up to dyno we use. We also just made 272ps on Dynapack @tcf=1.06 SAE with just JDM K24A2 block + DC5 oil pump + RBC cam gear using E20 OCT91(RON95). It would make less on some other dynos.

@TEHBR0LY 11 месяцев назад

❤

@XGNPerformance 11 месяцев назад

SUH DOOHHHHHHHHH

@วิศักภูเขัยว 8 месяцев назад

สุดยอดคับ

@justinwang9026 Год назад

May I know How much it cost ?

@XGNPerformance Год назад

Hi Turbocharging cost around $1,500-1,800 up to the turbo we have to use, with some Chinese parts and custom fabrications. Building the engine is entirely up to the parts we want, rebuilding labor cost alone is about $800-1,000 not including parts. Tuning costs $500-800. I can do online tuning for many cars. Whatsapp +66864099800

@xerxestheii856 Год назад

@@XGNPerformance oh that's expensive 😂

@Rimbabara-r1e 9 месяцев назад

in dollar or thailand bath sir? @@XGNPerformance

@XGNPerformance 9 месяцев назад

@@xerxestheii856Yes, even with Chinese parts, it's not cheap. But all these will make it a lot less than what we usually had to spend back in time. It will be much more expensive with all genuine parts.

@XGNPerformance 9 месяцев назад

@@Rimbabara-r1e It's in USD.

@vtecminileon 9 месяцев назад

Can you please tell me why you used the R20 pistons over stock r18 pistons?

@ravi210878 11 месяцев назад

Hello. Where is your location. Can i add same turbo and tune stock ecu on my r16a

@XGNPerformance 11 месяцев назад

Hi Im in Thailand. My Whatsapp is +66864099800

@XGNPerformance 11 месяцев назад

I have partners in many countries. Maybe we can arrange something.

@AThao-q1d 10 месяцев назад

8th gen civic vtec turbo

@XGNPerformance 10 месяцев назад

🤝

@theconiq2274 10 месяцев назад

Hello. Doy you make turbokit for me?

@rickyboostedhonda27 7 месяцев назад

What turbo manifold was that ?

@XGNPerformance 7 месяцев назад

Stock bro

@XGNPerformance 6 месяцев назад

I was reading it wrong and thought u were asking about intake 🤣. It's custom made locally.

@xx_kisalove_xx Год назад

*just get a si motor*

@lovepreetkular2264 Год назад

Why

@XGNPerformance Год назад

I'm happy for you that you have such options in your country.

@_xx.bugz.xx_ Год назад

There is nit one civic si in my country

@XGNPerformance 11 месяцев назад

@@_xx.bugz.xx_ so we are in the same boat🙂

@AkilAmmon-iw2vu Год назад

👍

@Budgetmealracer 11 месяцев назад

What injectors are you using bro? And how many cc?

@XGNPerformance 11 месяцев назад

Chinese 650cc injectors bro, but it's maxed out. I recommend using 850cc for stock fuel system.

@Budgetmealracer 11 месяцев назад

Ok brother thank you, we are planning to build and r18 turbo with stock internals with skunk2 cams. Is 400-500cc injectors good?

@XGNPerformance 11 месяцев назад

@@Budgetmealracer No problem. How much boost?

@Budgetmealracer 11 месяцев назад

@@XGNPerformance my kit is still in transit and we will install in later on. My tuner mr. Julius told me that we will run on low boost only. By the way if i would use a k20 injector would it work bro?

@XGNPerformance 11 месяцев назад

@josemichaeljochin870 K20 will only be enough for super low boost. Does is happen to be Julius from Philippines?

@henrycoool Год назад

Stock internals?

@XGNPerformance Год назад

Chinese forged rods and Honda OEM R20 pistons

@kpraz 11 месяцев назад

wow just a year im jealous

@XGNPerformance 11 месяцев назад

With over 20 years of time spent with computers, helps a lot with firmware reverse engineering. Also, studying engines and cars and observing live data from cars for years. We also do road constructions and do all the maintenance of machineries ourselves at home.

@lovepreetkular2264 Год назад

Ratatatata👌

@XGNPerformance Год назад

Brahpppppppppppppppppppp

@tehgibbles8314 Год назад

So boosed only to make k series with bolt ons power. Country restrictions suck

@XGNPerformance Год назад

Hi, thank you for watching. It's up to the owner of the car for what they like to do. And we assist the owner to achieve it together. As long as the owner is happy. We will be happy too!