3.0 Horsepower TECUMSEH Engine. H30 side shaft. HOW TO INSPECT Fix CARBURETOR ADJUSTMENT and TUNE

Подписаться 62 тыс.

Просмотров 26 тыс.

50% 1

How to Fix a 3.0 Horsepower TECUMSEH Engine that STARTS the DIES or STOPS. WILL NOT STAY RUNNING. H30 side shaft motor repair. Fuel gas delivery problems. STARTS but WON'T STAY RUNNING. Carburetor Service and Initial settings ADJUSTMENT. This style of TECUMSEH small engine CARBURETOR has several ADJUSTMENTS that are needed. Fine tune. FLOAT NEEDLE VALVE replaced. Initial presets preliminary adjustment explained. Specification.
Music by my band! BonzaiRod ~ song~ "My"
Copyright 2018 Jeff's Little Engine Service
For T-Shirts and Parts, visit my website!
www.jeffslittle...
Donations help, thank you!
www.paypal.com...
Sponsored in part by GRIP Tools, "they help me help you, check them out"
gripontools.net/
PLEASE KEEP IN MIND when you are watching my videos: I am demonstrating the least expensive, quickest "backyard", "backwoods"methods for repairing or servicing your lawnmower. Replacing all components such as gaskets and fuel lines is always recommended when rebuilding or repairing equipment. With these videos I hope you are able to fix and repair your lawnmower yourself with minimal parts, knowledge and tools. Remember to always work safely and follow proper mechanic procedures. Thank you for watching!
Jeff

Опубликовано:

10 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 43

@sargoon11 3 года назад

Best video ever I nearly burned the machine 🤣 thank you so much she is cutting beautifully on my real mower.🙏

@red380zzz 6 лет назад

i REPLACED MY CARBURETOR AND STILL HAVING ISSUES. i AM GOING TO ADJUST IT ACCORDING TO YOUR VIDEO AND SEE WHAT HAPPENS. VERY AWESOME VIDEO! GREAT MUSIC AS WELL!

@b1644 2 года назад

Thanks for this! I was able to get my old Troy Built chipper's Tecumseh H35 (very similar to the H30 but no speed control) running properly again. The tiny orifice in the side of the main jet needle was clogged. I cleaned it with a copper wire and the engine runs great now.

@JeffsLittleEngineService 2 года назад

Great to hear!

@andreyzagoruyko5390 4 года назад

WOW this is the BEST vid I have ever seen on small engine carb rebuilding; THANK YOU A TON!

@JeffsLittleEngineService 4 года назад

Wow, thanks!

@petedebo6906 8 дней назад

Sounds good....just so you realize you should have water at least in that pump so you don't burn the seals out

@piodambrosio1427 3 года назад

Hello Jeff,Hi, If you had disconnected the carburetor from the engine you could have cleaned it completely and worked on the carburetor more comfortably!

@piodambrosio1427 3 года назад

Hi Jeff If you had disconnected the carburetor from the engine you could have cleaned it completely and worked on the carburetor more comfortably!

@denisrodrigues9643 3 года назад

Hi, I'm from Brazil, Nice vídeo!

@JeffsLittleEngineService 3 года назад

Awesome! Thank you!

@denisrodrigues9643 3 года назад

please, i would like to know how much oil goes. i bougth one, and here theres no much like this. sorry my english. thanks.

@etwaroojai382 2 года назад

Nice video Jeff, very informative , I have the same 3hp engine on a Troy Bilt tiller I am working on at the moment .

@JeffsLittleEngineService 2 года назад

Thanks for watching

@Pointlesshandle48 2 года назад

Same

@stevesmith6058 5 лет назад

Jeff does everything the hard way

@JeffsLittleEngineService 5 лет назад

lol! I like to show what not to do

@richschafer3354 2 года назад

I love your videos!!

@JeffsLittleEngineService 2 года назад

Thanks Rich! You and me are friends now!

@Rokonmattadk 3 года назад

I have one without the throttle lever so one speed (genarator) it over revs like crazy, what adjustment would that be?

@JeffsLittleEngineService 3 года назад

govenor problems perhaps or a stuck throttle on the carb

@dylankountz6801 3 года назад

I have one I'm working on could u send me a picture of the carv and spring location's please

@anony13ousgamer55 3 года назад

Check magnets on fly wheel if come loose could be why

@walterdowns9012 6 месяцев назад

What happens if the float is too high or if it is too low at the loose end

@JeffsLittleEngineService 6 месяцев назад

Carb may leak if float is set wrong, or not run very well.

@heffedirte6243 2 года назад

That last low speed adjustment was awful fast

@susansanders3833 3 года назад

Jeff How do you set the idle screw? Is there a factory set number of turns out? Thank you for a very nice video... Well done

@JeffsLittleEngineService 3 года назад

it usually just screws in and pokes through other side about 4 or 5 threads

@Rokonmattadk 3 года назад

I have a very similar engine but way older, it does not have an governor leaver as it's a genarator, how do I adjust the low/high if there is none?

@jamesshivers8213 4 года назад

Good info, I have a 3hp Tecumseh and ot jas a diaphram carb on it. I was wondering if I could put 1 on it like the style on tour engine. Any help would be great, thanks

@JeffsLittleEngineService 4 года назад

I am not sure but it may be possible

@satlarsatlar 3 года назад

At 2:30 in on the video on the left side under that thin metal plate with the holes and spring attached; there is a black rubber tube coming out of the engine block. What is that? My Tecumseh engine has the same thing. It's not connected to anything. I can't find it in the manual or diagram for the engine. I haven't taken apart the carb on mine but it doesn't start w/o shooting some gas into the spark-plug hole. I wondered if this tube should be connected to a priming bulb or something. Thanks in advance!

@JeffsLittleEngineService 3 года назад

I think that may be the crankcase breather hose

@satlarsatlar 3 года назад

@@JeffsLittleEngineService Thanks for the reply. I've never heard of such a thing but have already found another video explaining what it does. BTW your video rules!

@roger4439 2 года назад

Partsfor Tecumseh

@red380zzz 6 лет назад

Hey Jeff I have followed all of your directions and it will idle on choke but will not run. I installed a new carb and cleaned the tank and carb and all I can get is it to idle on full choke. It was running great last year. Any suggestions? Thanks

@JeffsLittleEngineService 6 лет назад

sounds like a fuel delivery problem/ plugged carb. If it is an aftermarket cheap carburetor, that may be the problem too.