Love your videos. I am more of the Budget Rifle build rifles and believe your recommendations over others greatly. Thank you for what you do! You are so meticulous in your builds as well as all your reloading. I so appreciate your attention to details. Thank you Gavin for all you do. Your fantastic Sir!
Great video, makes a person realize just how much care and precision is needed to do things correctly. Videos like this bring a whole new level of appreciation into owning and shooting precision rifles. ✌️😎👍
When truing up the bolt face and taking material off it and other areas, wouldn't that change your headspacing? Or am i completely out of left field on that one? Lol
Every time I watch these very "information packed" videos I WISH that you would provide more videos of what you are talking about. I spend all my time trying to visualize what you did. Did I guess correctly? I never can tell without a lot more work. MORE VIDEO coordinated with less and more focused talk would really be an improvement. Tell us what you are doing as you do it on camera. I love your shop...I have the same equipment - learning to use. Great work...great results...just a little hard to follow for a visually oriented person like me.
@@Ultimatereloader it is relative as you said, but I really like how this shows that skilled labor isn't cheap for a reason! Will be really interesting to see how/if/ what difference there will be between these two rifles.
Nice video. The 300 prc is really catching on. Originally a 30-375 Ruger. What's cool about the 300 prc is u can use that ammo in a 30 Sherman mag. I got one getting made from Gray Sloan from swift Creek rifles. Batt action. Bartline barrel. 1.35 at shank. 1.25 at the end 30 inches long. Manners stock. Love your videos. Great builds.
Great info!! Great job showing where you have hiccups and how to recover. Not everything goes perfect. Should be some great comparisons between the two rifles. Wish more people would understand that “budget” doesn’t mean cheap. To help with some recoil management I would look at the limb saver butt pads with the air coils in them. I’ve put them on most of my rifles. They are a game changer
Gavin, I know there is a lot of folks that will thumb there nose at a 1/2" rifle and talk about how their guns will shoot in the .2"s or even .1"s but if the truth be known it is very difficult to shoot tight groups with a heavy recoil, sporter style stock. I prefer five shot groups to tell the story of consistency but with factory ammo and the style rifle, I would say that rifle is going to shine with handlaods and good (learned) bench technique.
I love the builds! It would be interesting to do an actual budget build, maybe get a used 700 or win 70 action and buy a very budget oriented barrel ($150-250 or even a low round count takeoff barrel for sale on forums) and attempt to put something together for under 'x' amount of money and compare the accuracy of quality components to budget components given the same time, care, and precision involved? Would be interesting to see, for me anyway. Keep up the good work!
My gunsmith did this with a slightly used Remington Long Range in 300 win mag. Just did the action/barrel blueprinting, and it shoots sub 3/8 moa. THAT'S a budget build.
@@stevensolinko8807 How much to blueprint barrel and action in your neck of the woods? Buying a Rem 700 from a guy for cheap so I have something similar in mind
I still find that, even though you do make a good case for the attempt to be sort of a gamble and a lot of time/effort/cash spent one something that might be, with luck as good as, something that we can rely on being great or even better. I prefere to use nonbudget parts, work/time is far to expensive were I live
Great video! Have you ever consider doing a build around the X-Bolt action and how that changes barrel and bottom metal fitting compared to the Remington 700 action?
Gavin, Have loved your videos from the outset as your are down to earth. I have a greater appreciation for the cost the gunsmiths charge for their work. I like this build but because I am recoil "shy" I would not consider a caliber of this nature. If you ever get the chance in the future to build a 16-17ib "Fly" rifle in say a 260AI I think that would be an interesting build and load development exercise. Have a great day from Australia.
Curious as to why u went with 300 prc over the rum ... you can drive the same high bc bullets faster with the rum ... my 30in barrel rum drives 212 eldx@ a bit over 3200...
I've thought about having my 7mm rem mag re barreled to a 300 PRC. In my testing the bipod is definitely the weakest link. It may be worth doing some testing/measuring on your end before writing off all bipods (hint Harris is the problem) square your rifle to the wall and measure the offset of the legs. Always bump the legs out one notch to make sure your not riding on the springs. Grab an atlas, why sit your $2000 rifle on a $79 bipod. I get the budget idea but there are some places not to skimp.
@@H43339 square the barrel to the wall or other flatserface and measure the distance to each leg, 3/8" difference isn't uncommon. Recoils will exploite this and it's why so many comp guys are moving to the atlas CAL or locking out the pan on their current bipods.
@@H43339 if you have time, take a look at all three parts of this video series. While bipod construction isn't directly addressed it's very easy to transfer to these mechanics of recoil over. Hope this helps clear this up. I believe part 2 is where bipod bouncing is looked at. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-whVH-FaZyQs.html
Have you thought about trying a different muzzle brake on the budget rifle? Like a Terminator or one from LR Customs? I would guess those would knock down the recoil quite a bit more. Awesome video and gunsmithing work. Love your videos
seeing your most recent content i wonder, are you looking into becoming a rifle manufacturer/gunsmith? It certainly looks like you are ready to produce your own custom rifles for customers to come!
Ola Gavintoobe, I hope you are very well, I wanted to say that I really like this program, but I would like you to put subtitles on what you are talking about, that there are many who see the program in all parts of the world, but do not understand what is speaking, because they speak another language, thank you very much and a cordial greeting from north cali, thank you very much for such a great contribution for the community and for the world
So all this for 0.5MOA now? Is it just me or does this not seem particularly impressive? My factory Mauser M18 can do that with factory hunting ammo when i have a good day. Just probably not for high round counts as it "only" has a 19mm barrel diameter at the muzzle. Something like a factory Blaser R8 can shot sub 0.25MOA with factory ammo if you do your part.
Outstanding work. About as close to perfection as you can get. And yes, for all the haters, this is a budget long range rifle. Maybe those viewers need to see the price tag on some real custom long range competition rifles.
I really enjoy watching your vids and I no that your choice of chambering is based on what’s new and popular but it seems a little biased based on hornady and what they have promoted. How about some comparisons builds to see if the new is better than the old chamberings might be fun for some new vids ! like 260 rem vs 6.5 creedmoore or something similar 300 ultra build vs 300 prc etc . I personally shoot custom built 6.5 x 284 and a crazy accurate 300 ultra lots of fun ! keep the vids coming !
Amazingly interesting build. Love following your projects, particularly the great detail and also seeing the work as you are doing it. The .300PRC is going to be my next rifle, but with limited choices in South Africa, I’m waiting for the Howa 1500 .300PRC to arrive. Custom unfortunately over here is LIMITED. 😔
Heinrich Stoltz ha! Another saffer. I literally said the same thing in my comment, limited with options. There is a company who is importing the Kelbly Into SA, just a bit of a wait for licensing and building, plus the costs. But would rather do it properly and wait for a proper rifle, than wait 18+ months (incl licensing) for a howa. Would be great to stay in touch!
First off thank you for providing so much epic content! I have a request.. can you somehow measure if your receiver in this 300prc build “RR” prefix rem 700 action is symmetrical at the rear scope base? I have heard that the newer actions need the rear portion of the scope base bedded. I also have done this on 4 actions to check. Place new never mounted steel base place it on action tighten front base screws finger tight. Now some will have a gap under the rear right side of the base as well as the entire rear section of the base is floating. The worst one I saw was the RR prefix I tried this on a C pre fix much older and it was rock solid. Also maybe I read the other comments and people don’t are up in arms about it being to expensive I have purchased everything to do this procedure from brownells for under $2000 I have 6 rem 700’s none of which have cost me over $400 buy a remage barrel $300-$700 and last time I checked a custom rifle that’s going to shoot that good will cost you $1500+ optics are opinions and don’t count in cost of rifle.
I'm asking because I'm just getting into all this also. If you are clocking your barrel with run out at the top, how does this affect your action truing. Doesn't it go against the whole bolt face truing?
I really enjoy your videos, I would like to re-barrel a Winchester model 70. It is in 7 mm Remington mag at this point, but would like to change to .300 Winchester magnum. If you are interested, I will supply whatever you need to accomplish this task. Please let me know.
It's not easy! You have to get an indicator tip in there and look for the "low spot" each time. You'll see the needle jump to the left and right, and you have to determine which direction is the groove, and use that as a reference. Perhaps I'll do an in-depth video covering this soon!
Gavin... what's your opinion on a 300 PRC vs a 300 PRC Sherman Improved (aka, 300 SM)? Just curious. I am wanting to build a custom hunting rifle in a 300 PRC, and am trying to understand whether the Sherman Improved version would be better. Of course it would allow for 2-or-so extra grains of water weight capacity -- but would it also help with the cartridge efficiency?
Makes no sense why people jump on these fads, 300 prc lol. Nothing special about it It's still a 30 caliber should have just left that ultra mag alone especially the way you had it shooting
Hey Gavin! Thanks for the great videos! I actually watched this 2 part video series on the 300PRC since I have been looking for some options in my country (South Africa) - in sa, we a little behind and we don’t have any stock rifles in 300PRC yet, apparently some are coming though. I specifically want to have my build in a MDT chassis, and being struggling to find options. I now see that you using a Kelbly Atlas action in a MDT ACC chassis - I had a call like just 2 days ago with the company who import kelbly into SA - can I ask, could I get the model number, or spec sheet for that action? As I would love to have it in the mdt chassis too? I know you mentioned it was a custom action, but not sure if you could tell me which base “model” you used? This would really help me. Thanks in advance!
To be clear- i enjoy the content- that said, the direction your channel has taken does not jive with the title "ultimate reloader" . maybe "a guide through basment manufacturing". I first started watching as i got into making ammo, not building firearms. I found you through some articles and you were one of my first tube subscriptions. (You and JRB, but he has gone dormant)This was a couple years ago. Personally, the equipment in your shop costs more than my house. Although it is cool to see you build these rifles, a "budget" build should be, to me, something sub 1k (optics included) with no need of gunsmithing. If your saving money by using tools that 99.9% of your viewers cannot afford than it defeats the purpose. That said, it is cool, i do enjoy it, I will continue to watch, and who knows, maybe ill win the lotto and be able to get me some of those machines.
Gary- if there are videos that don't suit you, please skip them. However, lots of great reloading budget content coming, including a LEE Loadmaster unboxing and other related content.
@@Ultimatereloader i watch em all! And enjoy them. I didnt mean to sound disrespectful, was trying to give feedback....im not the best writer..so i usually dont write comments. Like i said, i enjoy it but i guess the word "budget" is different pending on person.
Gary R - Very well articulated. Some of us unintentionally “triggered” Galvin, in the first part of this series. This series is a tour de force of gunsmithing. I’ve seen nothing else on RU-vid that gives such detailed information.
I have a long action magnum bolt sitting in my safe that I want to build on. But don’t know what route to take with it. I have a 300 win mag hunting rifle so I was leaning towards that. It would be a budget build. What’s a good place to start? should I look at 300 prc?
Budget 300? Use hand tools and a bench top mini-lathe, to true up and accurize a rifle that will give your 300s a hard run for the money. This would be something a lot of us could do. Follow along and paint by the numbers! Keep in mind we don't have sponsors, the odds and ends tools and devices must be cost effective. In other words, do something we can do too!
Just a thought, have you considered setting the video out so we see you do the work along the way and hear you talking as you work, rather than show us the finished product and hear you explain how you got there? It's very easy for me to suggest, much harder for you to do, I'm sure.
I'm planning how to do that, but it would be broken down into smaller segments- each machining operation covered in a separate story. Else, the video would be 5 hours long- or longer! :)
Hello , Nice video 👍🏻 About shooting a sporterrifle with a heavy recoiling caliber... I strongly recommend to read Nathan Fosters The Practical Guide To Long Range Shooting ☝️ Its about master and controling the rifle rather than the YotTube-ordanary free-recoil-manner that take a tremendous effort from the shooter to accomplish. I think you noticed that yourself with the different bag setup 💡 If... you buy the book ... Please don't hang up on Nathan's ruff language and jargon, just read the information ☝️ Greatings from Sweden 😁
Imo, this channel is going the same way 8541 tactical went. (Good or bad, take it how you want). Went from stuff everyone can afford, explaining how things work and why they do what they do and how to improve upon it.... to stuff only people who get a 2nd mortgage or would only dream of owning can afford to make " budget builds" out of...most costing in the 4k+ range *before optic*.
Thanks for the feedback (I appreciate feedback like this, especially when the person commenting is respectful like yourself). I would encourage you to check out my Budget Shooting and Reloading playlist: ru-vid.com/group/PLApPU7t86M4v6F0GuTBeF0-f6ghRR_RlI -- I'm hoping to do a lot more budget oriented stories this year... Including loading plated bullets. Stay tuned!
Hi Gavin, have you ever looked into doing a short chamber re-barrel job? Can do a for quite a bit less and don’t have to break the bank with equipment...barrel vise, action wrench, reamer T-handle extension, and reamer and gauges can be rented. Just an idea of what the average Joe can do in their garage.
@@Ultimatereloader yeah, I remember all those videos and there were great. I just feel if taking a R700, for example, and showing how it shoots then doing stuff to it with basic tool (or inexpensive ones) and show how it can improve the groups. Hell, if we can have 1000s of channels that all they do is "builds" of the same glock, then there should be room for Remington, savage's, rugers, Thompson, ect... even if the content is just how to lap lugs, adding pillars, to a factory stock (or atleast a stock under $400).
What's the advantages of ultra mag vs. win mag? I understand if you are hunting very large game but if you are using it for competition would the win mag be a better choice? That's is what PRC is right? Or am I mistaken and it's a new caliper ranking? Either way you do incredible work!! And your willingness to share your knowledge make you a truly remarkable young man!!
Ultra Mag ditches the belt, and is all about max velocity for standard long-action rifles. With powder charges up to about 100 grains, it's the kind of standard 30 cal magnums. 300 Win Mag is more of a staple/common 30 cal magnum with less recoil, less heating of the barrel, and longer corresponding barrel life (I presume).
total cost over 25K easy people depending on where and who does it, so in AU its would be around the 15K plus cost of good Extreme long long-range scope so add 5K so around 20K to 30K depending on which caliber, so a .338 or 300nm would be around that or you could buy a mk22 and get it blueprinted and then you will have a totally pro f class shooting platform for sure? 🙌🙌👍👍👌👌✌✌🦘🦘
