3D Print Not Sticking? 5 EASY 3D Print Bed Adhesion Tips

Подписаться 3,2 тыс.

Просмотров 19 тыс.

50% 1

Struggling with your 3D prints not sticking to the bed? 🤔 Don't worry, we've got you covered! In this video, we're sharing 5 EASY 3D Print Bed Adhesion Tips that will have you printing flawlessly in no time. From basic bed cleaning to fine-tuning slicer settings, we've covered all the essentials:
1 Clean Print Bed: Ensuring a clean surface is crucial for good adhesion.
2. Level Printer: Proper bed leveling is key to achieving uniform first layers.
3. Adjust Z Offset: Fine-tune the distance between the nozzle and the bed for optimal adhesion.
4. Use an Adhesive: Sometimes a little extra help is needed, try using adhesives like a glue stick.
5. Adjust Slicer Settings: Tweaking settings such as initial layer thickness and extrusion width can make a big difference.
Don't let print adhesion issues hold you back! Watch our video and get your prints sticking like a pro. 🚀 #3DPrinting #BedAdhesion #TipsAndTricks
Contact me: linktr.ee/ever...

Опубликовано:

15 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 27

@kevinvster 26 дней назад

Thank you! We had tried the blue tape on the Toybox and it was still coming up on one side. We then added the glue and that took it almost all the way. The last thing we did was slightly correct the level of the print bed and it is pretty much perfect with your other fixes. Where did you get the pre cut blue tape sheets? I have a roll but that looks so much easier!

@disquise2411 7 месяцев назад

All good and necessary points mentioned in this video :) Explaining the settings for cura came a bit short. The following settings in cura helped me print a better first layer on my old Tronxy XY-2 Pro: - initial layer Line width: 125% - printing temperatures: 200°C -> 205°C - printing temperature initial layer: 215°C (for 2 mm glass bed) - build plate temperture 55°C° -> 60°C (increase in inrements of 5) - use brim and brim width: 3mm Because the corners still lifted up from the bed sometimes, I installed a cura marketplace plugin called TabAntiWarping (Mouse Ears).

@everythingSTEM 7 месяцев назад

Great tips!

@dperloff 7 месяцев назад

I've printed for more than 100 hrs using a recently delivered Neptune 3 Pro with perfect adhesion: no glue stick, tape, brim or raft. I've been using the stock profiles in Cura 5.6.0 for slicing. The only thing I change , depending on the project, is the infill density. Printed parts (including complex print-in-place models) cleanly self-release after cooling. I primarily use eSun PLA+ but have had the same results with Printbed PLA filament. The only care I take is to not touch the surface of the metal plate and to not clean the metal plate in any way, including isopropyl alcohol.

@everythingSTEM 7 месяцев назад

Wow nice!

@ToastMaster553_ 6 месяцев назад

Thank you so much for making this video! It has really helped me find some new ways to stick my prints to my build plate, as currently, I have the ender 3 V3 KE which has some known z-offset and bed leveling issues as it is very new. Once again, thank you!

@everythingSTEM 6 месяцев назад

Glad it helped!

@thelastminuteman7513 3 месяца назад

I was getting curling and adhesion issues last winter. Long story short I decided the issue was it was just too cold in my office/workshop we were heating the house with the wood stove due to oil being astronomically high these last few years so rather then risk burning down my house and familywith a space heater o going broke on oil took a break from printing until late spring and I am still having adhesion issues. I tried painters tape and hairspray with seemingly good results, no curling consitent layers and good adhesion early on but what is happening now is 6-8 hours into the print when it's like 50- 70% through it comes off the bed. Going to try the gluestick next but I'm at my wits end. I don't understand how it's adhering well early on by my prints keep opting out closer to the end.

@titanmxatv 3 месяца назад

I'm in the same boat 6hrs into a 23hr print and it came off the bed so pissed off with it now i don't even want it 😂

@ATKDERBY2010 15 дней назад

Best explanation on RU-vid, Infact anywhere. Thanks a lot

@kevinbaker26 7 месяцев назад

I have a Neptune 4 and used the included glue stick. I just found it too messy and so switched over to spray glue. I find it much easier. I have no adhesion issues and it's far less messy.

@everythingSTEM 7 месяцев назад

Nice tip! I’ll have to try it. I just ignore the mess 😂

@kevinbaker26 7 месяцев назад

😆

@marksmales2204 6 месяцев назад

And ruined the bed plate!! 🤣🤣🤣

@nicollerichardet8140 Месяц назад

@kevinbaker26 what spray glue did you use?

@kevinbaker26 Месяц назад

I used a spray called 3dLac from Amazon. And, no it does not damage the pei plate

@Piscyn33 Месяц назад

I got a Ender 2 Pro, did no more than 10 prints in the past year for my daughter, now I can't get it to work. I've spent 5 hours tonight, replaced the nozzle, new role of PLA filament from Ender, cleaned the magnetic plate, recheck and leveled it again, baby step the z axis, print the tuzi g-code it came with to make sure it's not a model problem, de-greased the magnetic plate again, increased bed to 65 instead of 60, slowed down the print, and it Just Won't Stick... I'm so close to spare parting this thing. I will try the glue stick method tomorrow. Any other ideas please advise.

@ATKDERBY2010 15 дней назад

Did you figure this out mate? Mines being a little shit lol

@jaysoncl6457 27 дней назад

Creality Ender 3 v3 se using PLA mainly and use PETG all have trouble sticking to bed whats ideal temps for both and i get very fine lines on prints when it works

@ebood171 2 месяца назад

0:45 i dont have dust i have scraches how do i remove them

@colbyallen5258 2 месяца назад

Get a new bed

@ebood171 Месяц назад

I did but I got a refund and I bought a new one it worked

@m7chase113 3 месяца назад

So I just got my printer I know it’s leveled i made sure of it many times the glue works and is sticky not to sticky but when I do the print like a tiny cube the print will not stick to the bed and start to follow the nozzle like it’s stuck to it because it is how do I keep the filament to stick to the bed and keep the nozzle from dragging the print around I’m new to 3d printing and there are no tutorials to the problem I’m having

@wolforix9599 3 месяца назад

Same here tell me if you found a solution

@marksmales2204 6 месяцев назад

Even any kind of glue, even pritstick can ruin the bedplate, so why even suggest it.

@everythingSTEM 6 месяцев назад

The glue literally came with my 3D printer

@captiandarwin 4 месяца назад

Why did you not do that in the first place. I'm really curious why he did not take your own advice. Because if you had done that in the first place you would not have that mess. So now you're telling everybody What you did not do, or you would not have that mess.