Привет! Помню в каком - то видео сказал, что покажу, как устанавливал удлинители станины и изменял высоту моего токарного станка record power coronet herald. Вот, показываю ))
Ничего сложного на самом деле нет - самое главное не торопиться не терять болты и не превышать момент затяжки. Это правда сделать достаточно сложно без динамометрического ключа, но мы люди не боязливые, закрутим обычными ключами, как говорится, по наитию, на ощупь.
Станок уже был установлен на ноги, так как порожки и удлинитель я заказал позже, чем пришел сам станок, а попробовать его в работе хотелось сразу, не ставя на режим ожидания в течение целого месяца. Вот и буду разбирать и собирать все заново.
Удобнее всего, конечно, использовать какой-то мобильный верстак, к примеру как у меня. Тут важно, чтобы грузоподъемность позволяла поместить весь весь станка на стол, так как весит он не мало.
Открутив все ножки, примеряю положение поставок. Ошибиться сложно, все довольно понятно. Теперь необходимо прикрутить их и уже затем сверху ножки. Кстати не помню, говорил или нет, но ножки можно заполнить песком и тогда станок будет еще надежнее стоять на полу. Я не засыпал, на данный момент мне устойчивости хватает. Постарался показать все максимально подробно. Может кому и пригодится, ведь на примере гораздо проще, чем быть первооткрывателем. Сэкономлю чье-то время.
Теперь приступаю к удлинителю станины. Вещь недешевая, в районе 180 евро, но к сожалению без этого невозможно точить длинные детали, а так я смогу выточить почти метровую заготовку. Деталь обильно покрыта малом для защиты и, конечно, я его хорошенько очистил. Установка опять же не сложная, но первый раз я поспешил, невнимательно посмотрел и прикрутил неправильно. В результате поверхность удлинителя оказалась на пол миллиметра выше основной станины и задняя бабка при переезде застревала. Для того, чтобы исправить косяк - пришлось все перекрутить по новой. Теперь все четко.
Всем спасибо и пока! SawAxeHammer
Hello! I remember in some video I said that I would show how I installed the bed extensions and changed the height of my record power coronet herald lathe. Here, I show))
There is really nothing complicated - the most important thing is not to rush, not to lose the bolts and not to exceed the tightening torque. It’s true that it’s quite difficult to do this without a torque wrench, but we are not fearful people, we will twist it with ordinary keys, as they say, on a whim, by touch.
The machine was already installed on its feet, since I ordered the sills and extension later than the machine itself arrived, and I wanted to try it in work right away, without putting it on standby for a whole month. So I'm going to take it apart and put it all back together.
The most convenient way, of course, is to use some kind of mobile workbench, for example, like mine. It is important here that the load capacity allows you to place the entire machine on the table, since it weighs a lot.
Having unscrewed all the legs, I try on the position of the supplies. It's hard to go wrong, everything is pretty clear. Now you need to screw them on and then on top of the legs. By the way, I don’t remember whether I said it or not, but the legs can be filled with sand and then the machine will stand even more reliably on the floor. I did not fall asleep, at the moment I have enough stability. I tried to show everything in as much detail as possible. Maybe someone will come in handy, because the example is much easier than being a pioneer. I'll save someone's time.
Now I'm going to start the extension of the bed. The thing is not cheap, around 180 euros, but unfortunately without this it is impossible to sharpen long parts, otherwise I can carve an almost meter-long workpiece. The part is heavily coated with small for protection and of course I cleaned it well. Installation, again, is not difficult, but the first time I hurried, looked inattentively and screwed it wrong. As a result, the surface of the extension turned out to be half a millimeter higher than the main frame and the tailstock got stuck when moving. In order to fix the jamb - I had to twist everything over again. Now everything is clear.
Thank you all and bye! SawAxeHammer
Asteroid by KV / kvmusicprod
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/3wBMpV1
Music promoted by Audio Library • Asteroid - KV (No Copy...
13 авг 2022