4L60E Problem 1-2 shift fixed

Подписаться 14 тыс.

Просмотров 39 тыс.

50% 1

This is the second video showing this install with a POV hat of the install. I tried to get a better camera angle for this video and for the most part it worked! There are a couple steps that the camera slipped and you can't see everything, sorry I didn't realize it till I was done. I talk you through it and if you keep watching you can see what was done after it's assembled. I have this video • 4L60E SHIFT PROBLEM FIXED I did before that shows it also.

Авто/Мото

Опубликовано:

27 фев 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 48

@stevea6722 Год назад

For those that say you shouldn't put the Vette servo in a heavy vehicle, According to ATSG service manual, the following 4L60-E transmissions have the “Corvette” servo installed from the factory, based on the center hole dimension on the divider ring. The trans codes stamped on the passenger side pan rail on the trans are: CHD CJD CKD CLD KCD KDD Always check to see what the casting number is on the divider ring.

@anthonysourdiff1835 3 года назад

Thanks for video Danny

@gearbender427 Год назад

The camera aiming reminds of a bootleg movie I once bought, LOL, thanks for the vid anyway.

@jimlevering4613 3 года назад

Thanks for the info from your average Joe.

@gustavomelendez5514 3 года назад

Tanks brother 🇺🇸🇨🇦🇲🇽 4 ever

@AlexHernandez-gh3gr 17 дней назад

why wouldthe servo to the band affect 1-2 shift?

@christal7480 Год назад

Do i just look up corvette servo kit 4l60e???

@AtanasDimitrov954RR 2 года назад

do u have part nymber?

@randybryant9936 3 года назад

Cool

@chrissexton6697 3 года назад

Lot better than taking it to the trans shop! Good video didn’t seem to involved!

@gearbender427 Год назад

As long as you don't damage a seal.

@ajsalazar8185 3 года назад

Great video. Any chance I can get a link to where I can buy it. And will this fit my 08 4L60e trans?

@96_12v Год назад

Will fit up to 2013 4l60e

@floydwalls4555 11 месяцев назад

@@96_12v YUP 700R4 4L60E Corvette Servo Visit the AUKEY Store

@Legendary_Frank Год назад

I just put the corvette servo today on the same exact car it sucked to change cause on my heat Shield it hangs on the transmission and the bolt was seized so I had to bend it lmao

@billybritt5334 2 года назад

I have a 4l60 that sometimes won't shit to second gear when this happens I need to come to a complete stop and place in park then back to drive and then she I fine for a while any ideals

@appliancedude63 2 года назад

Check the accumulator 1st

@mikey5150 Месяц назад

W0w me too😕

@jaywalla1337 2 года назад

Mine won't shift into second until you let way off gas and let it catch up, than wants to slip back into first if you try to accelerate to fast, and will shift straight to 1rst from 3rd if you step on it while it's in 3rd. I already changed the two cheap solenoids with no change. If I take it really easy and help it shift up by playing with gas a little bit seems to do fine. Still trying to figure it out.

@a148ru 2 года назад

hi, I have such a problem, I haven't fixed it yet. did you succeed?

@jaywalla1337 2 года назад

@@a148ru I fixed mine by upgrading to a longer servo pin, replaced the accumulator Pistons with aluminum pinless ones, and installed a Corvette servo. Hopefully that helps.

@nickwooo1 Год назад

@@jaywalla1337 happen to have a part # for the longer servo pin? Mines having the same issue as you stated. Thanks

@jaywalla1337 Год назад

@@nickwooo1 Sonnax 77787-02K Servo Pin

@nickwooo1 Год назад

Thanks I ended up welding a bead on top the pin and it worked. Is your trans still holding up?

@Sloba1992 2 года назад

I have Chevy Colorado 2011 2.9l engine, 60k miles, when I put in drive there is delay like 1-2 seconds before is in 1st gear, i got stuck one time in snow and i was shifting drive-reverse many times before i got out, since then i have delay always when i shift from parking to drive, everything else is working good, but I would like to fix that delay, what I should do/change ?

@slow_restoration 2 года назад

Could be a number of things. I don't get that deep into a 4L60 without a rebuild. Sonnax makes some upgrade pins and pistons that may be able to help yours.

@andonair3281 2 года назад

Did u fix it I’m Having the same issue

@Sloba1992 2 года назад

@@andonair3281 didn’t do nothing yet, still have 2 seconds delay every time when put from parking to drive, it shifts normal between all other gears, I was thinking to change solenoids and to put new oil and new filter.

@ypautomotriz Год назад

is it neccesary drain transmission oil from oil pan?

@slow_restoration Год назад

Nope, not necessarily.

@DC-zl8ww Год назад

Are the sealing rings made of metal or plastic?

@slow_restoration Год назад

Not sure what they're made of but not metal.

@ranielias6717 Год назад

Why can’t we see what your doing putting back together

@Nzchimeran 3 месяца назад

Great vid how to use pry bar to push it in . I'm doing this tomorrow now I know I don't have to pull the trans out 👍 Thanks

@slow_restoration 2 месяца назад

Thanks for watching!

@lisandro.20k Год назад

How much would a transmission shop charge for this job & if I supply the parts?

@whowho7969 2 года назад

What problem were you having with the 1-2 shift ?

@slow_restoration 2 года назад

A soft sliding feel to it. Kinda like it slips, delay between gear changes.

@peterpurol7873 Год назад

@@slow_restoration Yeah, I just bought the 2nd gear Sonnax Servo Kit... I hope that helps (at least a little) with the slipping and slow gear changes (1-2), but you know I'll have to drop the transmission... sooner than later...

@chriscompton1926 Год назад

Is this a joke lol you can’t see anything after camera slips

@andrewpope1122 Год назад

Everything youre trying to show is just out of frame... im sure thats the complaints u were speaking of in the beginning

@hot99pas 2 года назад

Horrible video that started out ok, please edit before posting.

@BadGrandpa101 Месяц назад

It sucks your camera is above the parts you're working on, now I've wasted time and have to watch another video where I can see the process clearly. Maybe refill and edit those parts