5 Tips for a Smaller Pedalboard

Подписаться 184 тыс.

Просмотров 112 тыс.

50% 1

Today, I'm showing you 5 space-saving pedalboard tips to help you get a smaller, more compact rig!
With so many great pedals on the market, it's hard to decide which pedals will make it onto your board, and which pedals go back on the shelf. With these 5 tips, I'll help you maximize your pedalboard surface area so your favorite pedals can go right where they belong: on your pedalboard!
TABLE OF CONTENTS:
00:00 Introduction
01:10 Tip 1 - Top Jacks!
03:16 Tip 2 - Use a Riser!
06:19 Tip 3 - Low Profile Cables
09:11 Tip 4 - Low Profile PSUs
11:06 Tip 5 - Effect Pedals w/High-Quality Buffers
12:51 Outro
Gear Recommendations in this Video
Pedalboard Patch Cables: www.therigdr.com/products/pat...
Tiered Pedalboards: www.vertexeffects.com/store#!...
Individual Pedal Risers: fixpedalboards.com/pedal-risers
CIOKS 7 - amzn.to/3d4qOty
CIOKS 8 - amzn.to/2zW5YOn
CIOKS 4 - amzn.to/33jWAOZ
Truetone CS6 - amzn.to/2wWLbII
Voodoo Lab Pedal Power 3 - amzn.to/3asqK6r
⬇️Private Tone Consulting from the Rig Dr. ⬇️
therigdr.com/collections/all/...
🔽Buy our Pedals/Pedalboard Materials🔽
Zip Ties: www.therigdr.com/collections/...
Tie-down Mounts: www.therigdr.com/collections/...
Velcro: www.therigdr.com/collections/...
Pedalboard Patch Cables: www.therigdr.com/products/pat...
Instrument Cables: www.therigdr.com/products/gui...
Pedalboards: www.vertexeffects.com/store#!...
VERTEX Pedals: vertexeffects.com/store
⬇ DIY BUFFER INTERFACE DIAGRAMS, TEMPLATES, & MATERIALS ⬇
Mono - vertexeffects.com/diy-buffer-...
Mono w/Tuner Out - vertexeffects.com/diy-buffer-...
Mono w/Splitter - www.vertexeffects.com/diy-buf...
Mono w/Audition Loop - vertexeffects.com/diy-buffer-...
4 Cable Method (FX Loop) - vertexeffects.com/diy-buffer-...
Wet/Dry - vertexeffects.com/diy-buffer-...
Stereo - vertexeffects.com/diy-buffer-...
🔻 //rig consulting//🔻
therigdr.com/collections/all/...
🔈 //podcast//🔈
Apple: apple.co/36dSQzK
Spotify: spoti.fi/2WGLku8
⬇ RECOMMENDED MATERIALS ⬇
some urls below contain affiliate links
//buffers//
Vertex DIY Buffers - vertexeffects.com/diy-buffer
Mesa Boogie High-Wire (dual buffer) - bit.ly/2lZwS0s
TC Bonafide Buffer (x2 input + output) - amzn.to/2vrTSug
Truetone Buffer (x2 input + output) - amzn.to/2NLDA8l
//power supply//
CIOKS 7 - amzn.to/3d4qOty
CIOKS 8 - amzn.to/2zW5YOn
CIOKS 4 - amzn.to/33jWAOZ
Strymon Zuma - amzn.to/3dpZANe
Strymon Zuma R300 - amzn.to/2ZgLclt
Truetone CS6 - amzn.to/2wWLbII
Truetone CS7 - amzn.to/2x1Nf2k
Truetone CS12 - amzn.to/33rfLq3
Voodoo Lab Pedal Power 3 - amzn.to/3asqK6r
IEC Plug Covers - bit.ly/34fpGl3
//dc power cables//
2.1mm DC Power Plugs (right angle) - bit.ly/2pGqXzI
2.1mm DC Power Plugs (straight) - bit.ly/36wd1sA
Bulk Power Cables (pre made) - amzn.to/3ev1q0t
//midi//
MIDI Plugs (right angle) - bit.ly/2oKHDFG
MIDI Plugs (straight) - bit.ly/32fNNLF
MIDI Cable (bulk) - amzn.to/2tPAHWQ
//velcro//
Vertex Super Lock - therigdr.com/collections/all/...
//cable management//
Zip Ties - www.therigdr.com/products/zip...
Tie Down Mounts - www.therigdr.com/products/tie...
Tone Essentials Kit - www.therigdr.com/products/ton...
//pedalboard tools//
Soldering Iron - amzn.to/2TTdMI4
Solder (60/40) - amzn.to/2U7XhsD
Solder Dispenser - amzn.to/2GpgMpR
Octopus Arms - amzn.to/2V3O8OD
Wire Strippers (30-20 AWG) - amzn.to/2BBMI6n
Wire Strippers (20-10 AWG) - amzn.to/2EbhBR3
Wire Snips - amzn.to/2EazwqU
Vise - amzn.to/2E9eTLO
Heat Gun (embossing gun) - amzn.to/2BwGdlm
Label Maker - amzn.to/2BCBcHU
Label Maker Tape (black) - amzn.to/2Cd3CZe
Label Maker Tape (clear) - amzn.to/34piDD4
Deoxit D5 Contact Cleaner - amzn.to/2GEm4gu
Truetone Milliamp (mA) Reader - amzn.to/2F9v3VN
Tone Brush - amzn.to/2HIfze3
Upholstery Crow Bar - amzn.to/2HIOU0K
Multimeter - amzn.to/2YW9BdE
Goo Gone - amzn.to/31rGJeS
👇 // diy diagrams // 👇
DIY Power Cables: vertexeffects.com/diy-power-c...
DIY Interface: vertexeffects.com/diy-interface
DIY Buffers: vertexeffects.com/diy-buffer
#PedalboardTips #PedalboardBuild #RigDoctor

Видеоклипы

Опубликовано:

29 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 313

@VertexEffectsInc 3 года назад

What are some of your solutions for saving space on your pedalboard? Let us know in the comments below! TABLE OF CONTENTS: 00:00 Introduction 01:10 Tip 1 - Top Jacks! 03:16 Tip 2 - Use a Riser! 06:19 Tip 3 - Low Profile Cables 09:11 Tip 4 - Low Profile PSUs 11:06 Tip 5 - Effect Pedals w/High-Quality Buffers 12:51 Outro

@RulgertGhostalker 7 месяцев назад

another thing some builders don't mention is, Don't use any time based effects .... you don't need pedals like that. get / use plugins in your DAW environment, and let your venue's natural ambiance be your reverb....( some people would argue that.. i of course understand, but i don't )

@maz7100 3 года назад

For about 20 years now I’ve used old cassette tapes ( in their cases) and then wrapped with electrical tape …then I put Velcro on the top/bottom to attach it to the board… works quite well as a riser… it’s just enough space to clear jacks and make room. 🤣

@VertexEffectsInc 3 года назад

Ha! Good call

@theviolinoob Год назад

Genius

@phunkyjunkee Год назад

I use wood pieces with Velcro on each side

@GregVanAlstyne 4 месяца назад

We need to hear those 20-year-old cassettes! Time to bust them out on RU-vid for an anniversary party 🎉

@lancecox8084 3 года назад

Just wanted to thank you Mason for all the tips and recommendations on pedal building and getting the best results, Thanks to spending almost a year and a half in lockdown and turning my focus back to music to get through it all, I defiantly went Pedal crazy and made it a major project to build my ideal Pedal-board, your live shows have provided so much help in doing a pro job!

@VertexEffectsInc 3 года назад

I’m so pleased! So glad I could help

@peterbrusch1493 Год назад

This Channel is a fountain of knowledge about pedalboards. Thank You for letting me take part in Your enormous experience in building pedalboards. Helps me a lot!

@MrSpeed-lt8gr 3 года назад

Thank you for your tips, Mason. It’s unreal how much pedals and pedalboards have evolved since my plywood pedalboard that I spray painted black and covered in Velcro back in 1998 🤣😂

@VertexEffectsInc 3 года назад

Oh boy! They have evolved alright!

@TheJD616 Год назад

This was exactly the info I was looking for! I kept running into the “use fewer pedals” advice. The individual pedal risers will be a game changer for me. Thanks!

@Mindartcreativity 3 года назад

After the first rehearsal with my new band a few weeks ago, I decided to switch my big homeboard to a Pedaltrain Nano+. It was too heavy(over 12 pounds/6kg!), too big and too many pedals I didn’t need. For my band I only use a tuner, a distortion and OD, a fuzz and a reverb/delay. My tip is to start with the smallest board you can get away with. Secondly, decide the minimum of pedals you really need and USE. Thirdly, get pedals that can do multiple things. For me, I use reverb and sometimes delay, so instead of using seperate pedals I use the Boss RV-6 which can do reverb+delay. It made me really understand how to use these effects once I was limited. With the Nano+ I use a Cioks DC5 so I have 5 outputs for 5 pedals or 6 pedals if I daisy chain two pedals. I have 3 drive pedals, a TS Mini, a Mooer Black Secret and an EQD Cloven Hoof. The first two are daisy chained as they only draw 10-20mA. The output that remains free is my wildcard slot. Sometimes I add a POG2 (yes it fits although sideways) or a chorus or even an additional drive pedal. My tuner is a Polytune Mini. Although I hate mini pedals because of my shoe size, it‘s the best way to go to save space and weight. The best thing is, I can just grab my board (it weighs just 2.5kg) and my guitar and take public transport to our rehearsal space AND I still have every pedal I really need for my sound/band. I don‘t regret my decision of downsizing at all.

@VertexEffectsInc 3 года назад

Thanks for sharing this...looks like by the "likes" people are already finding this helpful!

@Mindartcreativity 3 года назад

@@VertexEffectsInc Glad to share my thoughts. And thank YOU for making this channel, I have learned a lot especially about power supplies which is quite important.

@VertexEffectsInc 3 года назад

@@Mindartcreativity I'm so glad!

@rbroderick 3 года назад

Great info 👍 Looking at building a pedalboard to electrify my sax.

@VertexEffectsInc 3 года назад

You should!

@hummarstraful 2 года назад

That is a LOT of information packed into a 15 min video. This channel is a must-subscribe for guitarists. I keep coming back again and again for the best pedal info anywhere.

@VertexEffectsInc 2 года назад

Amazing!! Thanks for the support!!

@zealfer 2 года назад

Hi Mason, I just want to say thank you. I am now enjoying my pedalboard because of the tips you've shown here. I've built my own compact pedalboard and it works so well!

@VertexEffectsInc 2 года назад

Great to hear!

@joshbaker5403 2 года назад

Just starting my first bass pedal board. This video really helps. Thanks

@VertexEffectsInc 2 года назад

❤️❤️❤️

@Corporations8MyBaby 3 года назад

Well done. All your content has been very informative and entertaining this past year but this one gets an extra plus on the "A" because of how concise and tight the points were ... matches the pedalboard.

@VertexEffectsInc 3 года назад

Thank you so much for your support! Really appreciate your viewership

@mbarlow111 3 года назад

Great. Super straight forward. trying to slim down as it were, as i like overly complex sounds. really nice job.

@VertexEffectsInc 3 года назад

Thank you so much for watching!

@flyguyty33 3 года назад

Great video! I build my own pedalboards out of wood and have them a few inches higher at the top to hide power supplies and cables underneath the board. Also drill holes on top of the board to run cables and power source to look clean.

@VertexEffectsInc 3 года назад

Cool you just need to be careful as many of the common power supplies aren’t designed to have pedals on top of them. You can create a lot of noise in some conditions

@safuan3573 3 года назад

Great tips as usual!

@VertexEffectsInc 3 года назад

Thanks for watching!

@johnschoppmusic 3 года назад

Love these videos Mason! Thank you! ~cheers

@VertexEffectsInc 3 года назад

🙏🙏🙏

@KristianHeartmusic 3 года назад

I feel like smaller boards are definitely coming back in popularity for sure

@VertexEffectsInc 3 года назад

Small power packed for sure

@samz9121 3 года назад

I heard it said from the key team in my worship team at church is that the PTJr is the perfect size for what we do if we pick our battles right. Buffer, comp, preamp, 3 drive stages, mod, delay, reverb and a Morningstar MC6 to control everything in wet land. All of this out to a Kemper and we have pretty much, in my opinion, the ideal church rig setup. All that’s left is to make space for altoids. (Iykyk)

@TheClicheGaming 2 года назад

for someone who is pretty much the authority on pedal building your channel took me way too long to find! thanks for the tips.

@VertexEffectsInc 2 года назад

Hope you found it helpful

@goingbananas 3 года назад

This is a very helpful video. This shows me a lot of solutions for my pedalboard that I will use. Thanks for this tips your the best 🤘🏻😁🤘🏻

@VertexEffectsInc 3 года назад

Glad it was helpful!

@lylesmith9547 2 года назад

I start my chain with the 3 tuner and finish with a Strymon Volonte as soon as it arrives. Can’t wait to try it out.

@VertexEffectsInc 2 года назад

Cool, just make sure the Tuner has a good in/out impedance and the Volante is set to the buffered mode.

@javier_arenales 3 года назад

Great tips Mason!

@VertexEffectsInc 3 года назад

Glad you liked it!

@manuleduc9465 3 года назад

Thank you, great value tips.

@VertexEffectsInc 3 года назад

Glad it was helpful!

@slimbeaux Год назад

Thank you for all your help.

@VertexEffectsInc Год назад

Thanks Slim!

@bluztime5271 3 года назад

Awesome info, thank you

@VertexEffectsInc 3 года назад

Thanks for watching!

@stevensrp2music985 3 года назад

Risers have made my life easier for years now. SP400s are a Godsend for sure and I really appreciate all of your info on them over the past year or so. Thanks for all the great tips and tricks!

@VertexEffectsInc 3 года назад

So glad you dig it!

@stevensrp2music985 3 года назад

I’m so glad I found your channel last year lol! Take care and keep it up

@VertexEffectsInc 3 года назад

@@stevensrp2music985 Thanks for watching!

@freddiemercury4552 2 года назад

Really love your channel.. The best..

@VertexEffectsInc 2 года назад

Thank you very much!

@Stereo1782 3 года назад

Great Tips really helpful

@VertexEffectsInc 3 года назад

🙏🙏🙏

@stretchedbag1963 3 года назад

Great tips Doctor! Some awesome boards featured here, makes me want to run and hide, my builds work… but they’re so ugly. Thanks for posting

@VertexEffectsInc 3 года назад

Hopefully through the videos you'll feel more confident to upgrade and make changes to your rig!

@KramAsylamStudio Год назад

Great content!

@VertexEffectsInc Год назад

Thanks for watching!

@VincVEVO 2 года назад

Cool video and good informations! Thanks man!!! ;)

@VertexEffectsInc 2 года назад

Happy to help!

@samz9121 3 года назад

My board is an odd bunch. A PT junior-sized board with 11 topside and 2 underside (including a One Spot Pro CS7) Topside, a DVP 3XL (because I like having a larger sized volume pedal) on the right side Next to it going down is an upright Mooer Yellow Comp, sideways Keeley Super Phat Mod, and an upright Sub n Up Top and bottom in the middle are the Strymon Iridium and the Pettydrive, joined by the Polytune noir and a riser mounted Wampler Tumnus for Klon boosted fun. All upright. To the left is from bottom to top, a Nova Delay, Specular Tempus, and a sideways Zoom multistomp. On the underside is a mounted CS7 and a Bonafide Buffer undermounted at the input. Slowly converting my patch cables to EBS Golds compared to the standard pancakes I've used all the while. The Zoom multistomp is for those fun effects I don't use as often and frees me up from missing the Strymon Timeline Ice setting, a Rat, a Julia, and straight-up distortion. Everything else is fair game for what I do. Lead is a Mogami silent plug and out to a passive DI.

@VertexEffectsInc 3 года назад

Nice!

@Not.Satoshi Год назад

I mount a power supply AND an innerface module under the board. I take the screws out of the module and use the enclosure cover plate as a template to drill holes through the board. Then I mount the module underneath with thick dual lock and use longer screws that go from top of board, through the enclosure covers screw holes, into the threads on the enclosure box. Often times pedalboards have a lip on the edge, in this case I use spacers between the enclosure and the underside of the board.

@VertexEffectsInc Год назад

Okay

@MrAxman53 3 года назад

I discovered the Polytune 3 with the built-in buffer a ways back and it's been at the front of my signal chain ever since. At the end of the chain, I use the buffer in my Eventide H9, which has an output impedance of 470 ohms. Works great. I have pristine signal even with six or more true bypass pedals in the chain.

@VertexEffectsInc 3 года назад

Great! The lower the better on the output impedance as possible!

@MrAxman53 3 года назад

@@VertexEffectsInc I have to imagine that Eventide knows what they're doing, right? 😉

@VertexEffectsInc 3 года назад

@@MrAxman53 it's not as low as I'd hope for, no analog dry thru either...not ideal for me.

@mr.brettjames 3 года назад

Thanks Mr Axeman, saved me searching for my H9's output! 👍🏼

@ccfmafia3301 3 года назад

It's cool seeing the polara on your board. It gets a bunch of love from synth guys but you don't see guitar player talking about it

@VertexEffectsInc 3 года назад

It's one of the best Verb's in town!

@macpakinga1271 Год назад

You da man brother thank you for sharing 🎸❤ im going solo. 🎸

@danielhunsinger8017 5 месяцев назад

I'm all for top jacks but the issue I find is sometimes they make the pedals to close together and you might press a pedal you don't want to turn On or OFF. I think the best way to maximize your smaller board is to give up having the same thing over and over. Multi effects pedals like programmable ones like the Boss 500 line is a really good way to have more pedals with less space.

@lavadoraautomatica1 11 месяцев назад

Waiting for the collider in the mail.

@druwk 3 года назад

Those Square pancake plugs look amazing! I’m determined to keep my pedal board small! Two for One pedals can also help? I’m a Fuzz kind of guy, so I end up with my Buffered Tuner Late in my chain. Getting everything on there, tidy, not too close, and functional is always a challenge? Still figuring out my Gain/Fuzz situation. So the right side of my board isn’t locked down yet! Saw an interesting demo where a player was stacking Overdrive into various Fuzz pedals...I’m intrigued? Right now I’m going the other way around. Have you ever thought about a “hinged bridge riser” with a slight angle (85*), instead of being so square? Pedals should be duel-locked down, and the slight angle would make it easier to tap the upper row and still clear the lower bout?

@VertexEffectsInc 3 года назад

Nope no angle...too perverse

@gustavoviveros8394 3 года назад

Great thank You 👍🏻

@VertexEffectsInc 3 года назад

You are welcome!

@kingslyashish 3 года назад

Another way of achieving a smaller pedalboard is by using The pedals which may do more than one effects or have presets (like in Overdrives )... The example would be Hx Stomp - we can run delay, modulation and reverb in one pedal or Chase Bliss Benson preamp or other overdrive pedals wich has preset or dual Overdrives , so that we do not have to have multiple Overdrives to get the sound. It's just my thinking.

@VertexEffectsInc 3 года назад

Yea, but the "Swiss Army Knife" stuff is always a tonal compromise compared to the real stuff it's trying to emulate.

@reverendg5937 2 года назад

Thanks

@VertexEffectsInc 2 года назад

No problem

@kenhillmusic 3 года назад

Great stuff. Any recommendations for road/flight cases?

@VertexEffectsInc 3 года назад

See the website, they’re all listen there www.vertexeffects.com/store

@kainagami 3 года назад

Guess that I have to get rid of all my MXR pedals :p haha Anyway, thank you for all your advices Mason!

@VertexEffectsInc 3 года назад

NO!!! Just for space savings and just a suggestions, not an absolute

@peterellwood2103 3 года назад

Nice video

@VertexEffectsInc 3 года назад

🙏🙏🙏

@bobbreckenkamp4641 2 года назад

Man, I wish you guys made a multi-tier pedal board that worked with zip ties. That's all I use. But I love your multi-tier design!

@VertexEffectsInc 2 года назад

Bob, zip ties are a no go for me, but Holey Boards might work for you - check them out.

@bobbreckenkamp4641 2 года назад

@@VertexEffectsInc I've been using the Holeyboard for many years, and before them I built my own out of HDPE (kind of heavy but easy to work with) but I like the layout of yours a lot. Just thought I'd ask. Thanks!!

@STRATMAN1969 3 года назад

Hi Doc You've been so helpful on this build I'm still working on .I'm wondering if I could once again get some advice? I think I've figured out by way of your elimination i.e. move power supply ,turn off buffer ,check each pedal. That the problem is in the jack of one of the inputs of my Walrus Phoenix .Is this something that can cause my amp to short circuit ,and fry pedals ( Malekko 616 dead ,and Taurus Dexter : ( Thank God I don't think it hurt my Keeley eccos when it shorted it out ,cuz it works fine on it's own adapter still in the chain. Would love any advise or thoughts . Thanks from a very sick board .

@VertexEffectsInc 3 года назад

The power supply has outputs (not inputs) but are you certain the polarity is right? Is the voltage at 9V? You can try measuring it to ensure that it's putting out 9V with a multimeter.

@TomaszGutka 5 месяцев назад

If my pedalboard starts with buffer in Polytune 3 mini, do I still should turn Buffer in Strymon Timeline which is last in my signal chain or it's better to put it in true bypass mode since the signal already has the right impedence? Between them there is Friedman IRX so a cab sim and maybe MS3 will also be added

@Contra2009 3 года назад

Would you please suggest a few options for input/output buffers for bass guitar? I’m struggling to find many that meet your suggested 2.2-10meg input impedance and 100-250ohm output impedance. Love the content! Many thanks!

@VertexEffectsInc 3 года назад

Watch our Bass Rig best practices video

@kodykindhart5644 3 года назад

🤘

@TheDilligan 2 года назад

One weird trick Ive found is that if something is going to be an always-on pedal, you may be able mount it underneath the pedalboard. I've done this with a Keeley compressor and a Boss Noise Suppressor on a Pedaltrain. Also one of the best ways to save space is to simply decide whether or not a pedal reeeeeally needs to be on your board. Like sometimes I want bucket brigade delay, sometimes I want tape delay. Could just get a digital pedal that does both OR, just pick one and deal with it. I also got a Strymon Sunset so that I don't have to have 4 drive pedals on my board. All the flavors are in a smaller footprint.

@VertexEffectsInc 2 года назад

All good points!

@oleksandrk4853 3 года назад

Hi Mason, just subscribed today, what a great source for beginners and professionals! Could you give me some links to build my board. I'm looking for power supply cables and connectors (I have strymon power supply) also midi right angle connectors and cables (5pin) I appreciate your time! I found some links below your video but some of them are jot available.

@VertexEffectsInc 3 года назад

If you just type/search in RU-vid for Vertex DIY Power or Vertex DIY Midi, you’ll find both immediately! Thanks for the support!

@slimbeaux Год назад

Thanks!

@VertexEffectsInc Год назад

Thanks Slim!

@rodolfoperez744 Год назад

Do you have any tips for a board that has 18 pedals and 3 of them are the boss ps6 boss ps5 and whammy rikochet? I use 2 buffer jhs one in the beguine and one in the end and still sucks a lot of tone, what can I Do?

@sorenrichenberg3313 2 года назад

7:54 another pedal, always a great thing

@VertexEffectsInc 2 года назад

Thanks for watching!

@DeGroove Год назад

Why doesn’t anybody make pedals with the jacks on the bottom of the pedals? Right where the cables should be, out of sight, underneath your board. With maybe some kind of modular jacks on the board, plug and play? Just an idea.

@offshot1st 9 месяцев назад

Question is do I do this with a tonex or buy a QC ... How would you run midi switching from a laptop?

@Mike_Spor 3 года назад

Pedal space....cant stop the addiction. I just build my boards around my pedals. My current "Scmiddt-array Friendman Mono" custom board clone is 20x40. That's 3 rows of pedals with two rows of space below. its more of pedal showcase and not for travel. I'll send photos when its done.

@VertexEffectsInc 3 года назад

Nice! Sounds like a cool rig!

@hiram6760 3 года назад

my solution for saving space is not to have many pedals on the pedalboard it may sounds funny but its true . now you only need few pedals perfect ex Jimmy Hendrix and I'm not going into that .. the main reason is to "play music" and to enjoy it . I would suggest you ask an expert like Mason to build you a professional pedalboard and be done with it , u only pay once and save tons of money and headaches unless u take time to know exactly what you really want and stick with it . knowing there is no such thing as a perfect sound also what kind of music u play will give u an approach ... thank you Kindly for sharing .

@VertexEffectsInc 3 года назад

But did Jimi use few pedals out of choice alone or what was available at the time? There fewer than 20 pedals at that time and he used Wah, Fuzz, and Uni Vibe. Now there are approximately 5,000 pedal makers with innumerable models. Apply that same ratio and 2021 Jimi has 100 + pedals on his rig ;)

@hiram6760 3 года назад

@@VertexEffectsInc "The enemy of art is the absence of limitations".

@ratobasherelectronics2668 3 года назад

What are good power supplies? My pedal board has in this order polytune3, DOD fx75b stereo flanger - splits into A = distortion pedal, B = into Boss sy1, A+B into EHX SMMH that outputs to A = bass amp B = guitar amp.

@VertexEffectsInc 3 года назад

Watch our Power Supply buyer's guide video! It'll tell you all you need to know :)

@kdub0529 11 месяцев назад

The MXR patch cables look low profile. Are they soldered? I don't see it in their specs.

@scottchristensen3694 3 года назад

What's your opinion of off-set and straight jacks to connect a run of side jack pedals to adjust for a bit of up n down instead of cable? Seems to work well. Your thoughts?

@VertexEffectsInc 3 года назад

No good

@Diax1324 3 года назад

What do you think of the EBS flat patch cables? I have a 29 pedals EUNA and I use a pancake-ended coily cable as my main cable, so I need EXTREMELY low profile cables to fit on the effects loop of that unit. Any experience?

@VertexEffectsInc 3 года назад

They are soldered, which is good, but it would never really work for anything that I do because you can’t customize them at all, and I don’t find them to be better sounding then what you can make on your own. A square plug is pretty low profile

@efsglass 3 года назад

@vertex effects in your experience would it be ok to share power on a switch mode supply(cioks hi5) between origin cali 76 stacked and a kingtone duellist? They can both run on 9 or 18 and the cioks has enough juice. Just not sure if its ok to share power with a compressor? Your thoughts/experience please?

@VertexEffectsInc 3 года назад

Try it - might be ok, there’s enough current there

@Jimbob-hp6ud 5 месяцев назад

I only use 5, Reverb, delay, modulation, distortion and tuner

@RulgertGhostalker 7 месяцев назад

the new Boss NS-1X has a 1Meg input impedance, but a 1Kohm output impedance.... but i think 1K is ok, because that should be ok for any input that is considered "high impedance", because that's a 10K minimum.....i mean as long as i am conscious to output into high impedance inputs only.

@youssefkasim7556 3 года назад

Is the Mesa Boogie STOWAWAY compact buffer as good as the high wire? Or what is the difference? Also, is the strymon Zuma a good power supply?

@VertexEffectsInc 3 года назад

It’s half of the High Wire, only a single buffer not a dual buffer.

@OlandoMcCall Год назад

Great vid only problem is if you have a board you'll have to covert over and there's no way to accommodate them(risers) with say a temple audio board. I'll eventually convert but it's an investment in time to do so....

@VertexEffectsInc Год назад

We make risers for these - releasing soon!

@OlandoMcCall Год назад

@@VertexEffectsInc getting money ready!

@OlandoMcCall Год назад

@@VertexEffectsInc keep in mine you'll have plenty with more than one size bought bigger and that still doesn't work. Your solution seems to work best as shown on a previous vid of yours. In my case I have a solo 18 that I could put above my dual 36, but I have no way to rise it. If that makes sense.

@chrisvoigt6895 Год назад

I am currently using a Walrus Audio Aetos. What are your thoughts on this Power Supply? (Personally, I LOVE it, but its a thick momma)

@VertexEffectsInc Год назад

It's a linear power supply - it has it's limitations.

@mikebostic5713 3 года назад

1. Dunlop mini volume 2. TC PolyTune 3. Keely compressor 4. Nobels ODR-1 5. Carbon Copy 6. Fender Deluxe Reverb

@VertexEffectsInc 3 года назад

"1 Tip for A Rig" :). Thanks for watching!

@arkavagoswami3068 3 года назад

Rig-1 a caline powerbrick tc sentry noise gate looping (ts mini mooer 009 preamp) tc corona chorus tc flashback 2 ehx oceans 12 mooer radar rig-2 xsonic xtone iPhone 7

@VertexEffectsInc 3 года назад

Nice!

@IndyRockStar 2 года назад

What type of pedal board buffer would you recommend? I was looking at the JHS Prestige. Any thoughts?

@VertexEffectsInc 2 года назад

We have a list of approved buffers in the description. Please look there for our recommended models.

@jm879 3 года назад

Question, im kinda stuck in between the pedal train meto 16 and 20. Im not sure if i want to add pedals since i tried mapping out and it fits in the metro 16 but it feels kinda cramped. Would you say i should get the metro 20 just so i have space?

@VertexEffectsInc 3 года назад

I don’t really know these platforms to advise - I never use them

@buttscarlton1830 2 года назад

do you think using a large d'addario XPND riser as a small "travel" pedalboard is a good idea? I'd only need something very small to fit 2 pedals (EHX LPB-1 and a DigiTech HotHead Distortion) that i would use with my black star fly 3 as a "travel" setup. i don't know what angle the risers are at and if it would even be possible to have it as a mini pedalboard. i just thought it might be a option since it comes with Velcro and is only $20.

@VertexEffectsInc 2 года назад

Don't know these risers. We also sell risers on www.vertexeffects.com for every size pedal.

@riverbard8287 Год назад

Have you ever thought about hanging the CIOKS upside down under the riser? 🤔

@Scott__C Год назад

Great info. Why are they called Top Jacks? Isn't the top the part we step on? Seems like it's the back of the pedal to me.

@oliverdepauw5663 Год назад

Seems like its because if the top is the part you step on then all jack positions would be side jacks and it would be harder to differentiate the said pedals jack configuration, could be wrong tho

@Scott__C Год назад

@@oliverdepauw5663 Not to me. The front is the part toward me, the back is the part away from me, left side and right side. Like if I were standing in front of a house.

@johoch24 Год назад

It's funny how in this video (2:02) he says "DC jack on the back", but then the audio jacks placed next to the DC jack are called 'top jacks'.

@stevecrounse1789 Месяц назад

Do you have a recommendation for a mini EQ?

@mellowmonsoon278 2 года назад

6. Use hybrid pedals like collider , brothers , etc.

@VertexEffectsInc 2 года назад

You mean like 2 in 1 type pedals?

@mellowmonsoon278 2 года назад

@@VertexEffectsInc yes

@keziahsantamariavillalobos3393 3 года назад

Uncle Mason, would it be possible to make blue tooth pedals? no cables needed, just synch them all together?

@VertexEffectsInc 3 года назад

Well we do have wireless, but there are some challenges with impedances and stuff like that there’s currently wireless MIDI but the receivers still need power and require batteries to work - were not there yet practically even with disregarding the electronics side.

@tompauljones2318 3 года назад

When making power cables, if I want to make a splitter to run to 2 pedals would you recommend the MC-1525 straight or the MC-1304 angled? For space the straight ends work best for my MXR Iso Brick. But if need be I can make 1 angled work amongst the straight ones.

@VertexEffectsInc 3 года назад

I use Kobiconn right angled plugs almost always. Rarely straight connectors. It depends on the diameter of the cable you're using for the DC.

@tompauljones2318 3 года назад

@@VertexEffectsInc I was planning on using the cable that Best-Tronics sells.

@VertexEffectsInc 3 года назад

@@tompauljones2318 I would just use what comes with your power supply and Best Tronics sells the Kobi Conn right angle connectors for DC power.

@joshgreen4521 2 года назад

Hmmm.. I'm a little confused. I watched a video where you talked about the essential reasons of getting a pedal which was dedicated to buffering the signal and not use pedals which are not build to buffer the signal. But in this video you are saying that the Strymon Big Sky - I suppose also Timeline and maybe the Blue Sky (I have these) are fine buffers? I also have the Daddario tuner - or would I need to get the TC electronic poly tuner to do the job? I have ordered 2 buffer pedals recently now, but are they really needed then?

@VertexEffectsInc 2 года назад

Having dedicated buffers is ideal in most cases, however for some they might have pedals that can achieve this internally. We have a video titled something like "Pedals With Great Built In Buffers" that has a list of all pedals that have our approved buffer specs, including the Strymon devices. Remember however these pedals need to be first and last to get the benefits of having an input and output buffer.

@joshgreen4521 2 года назад

I have read up on it. It seems to be the case that the Blue Sky has the input and output buffer quality as you specified. (y) I will use one of my ordered buffers in the start of my signal chain before my tuner which does not have buffer quality. There is 6 pedals in between the buffer and the Timeline. Will it be too much buffering with the Timeline right before the Blue Sky and the buffer in the beginning of the signal chain?

@VertexEffectsInc 2 года назад

@@joshgreen4521 The blue sky will only work as the output buffer if it's dead last, you'll still need an input buffer first.

@joshgreen4521 2 года назад

@@VertexEffectsInc I came to the same conclusion yesterday from reading up on my pedals. Thank you very much for quick reply! I love your content and I am very inspired by the pedalboards you design. 👍 I have one question remaining though: Is a Timeline followed by a Blue Sky too much buffering when they both have high quality in built buffers?

@VertexEffectsInc 2 года назад

@@joshgreen4521 I would bypass the buffer in your Strymon device that is not the last pedal in the chain. So if your signal path ends with the Timeline, Blue Sky, Amp - bypass the buffer in the Timeline, but keep it active on the Blue Sky.

@jfunky8721 3 года назад

If you have a wah and a fuzz. Would the polytune mini 3 be more effective first in the chain if it’s true bypass or buffered bypass?

@jazzzfer 3 года назад

Following... always wondered too

@gregorglasbruch6917 3 года назад

You need to test this. Some fuzzes lose their original sound (getting trebly and harsh) when they follow a buffered pedal, however, some don‘t.

@VertexEffectsInc 3 года назад

If it's buffered after impedance sensitive stuff after the input buffer. If it's true bypass it can go first.

@evanmiller2579 3 года назад

I am looking at getting the 10x17 one shown in the video however online, the picture shows an additional support in the middle of the riser which will make it impossible to fit my Fender Engine Room 8 under the riser. Is this middle support removable?

@eriksonderlon 3 года назад

I've seen Mason remove the middle support in other build videos of his.

@VertexEffectsInc 3 года назад

It's an optional leg, I always remove mine.

@Pokey7317 2 года назад

Great video... im curious. How much would is cost for you build a board for me using your pedal board options like the one in this video. Naturally I would have to ship my pedals to you of course. I would want it as small as possible of course. Kinda like the one this video. I basically have an MS3, TUMNUS MINI, SOUL POG, CRY BABY WAH, TUBE SCREAMER, EQ PEDAL. Thats it. Thanks again for the videos and looking forward to the next one.

@VertexEffectsInc 2 года назад

Not sure, we don’t offer this service for hire - just build a few boards here and there for RU-vid tutorials. I think most of the pedalboard builders out there range somewhere between $80 and $200 per hour - plus materials. A lot of the pricing depends on the builders experience and also what the scope of the rig is.

@Pokey7317 2 года назад

@@VertexEffectsInc Hey thanks for your quick response... I guess i'm gonna be visiting your website to get some materials... I love how CLEAN your boards are... HERE GOES NUTHIN' LOL

@VertexEffectsInc 2 года назад

@@Pokey7317 we're happy to assist as you go and consult on the board - there are options for that over on www.therigdr.com

@Pokey7317 2 года назад

@@VertexEffectsInc Cheers man yeah will do for sure. Thanks again

@thesoundpurist 3 года назад

Good music at the beginning what's that?

@VertexEffectsInc 3 года назад

I think it’s either from Tim Marco or Dann Huff

@ransom77 3 года назад

What do you think of the CIOKS AC10? I have an ancient Digitech pedal that uses a 9VAC adaptor that’s a massive wall wart, so I need a power supply that has AC options also. Should I be concerned with placement of something like the CIOKS AC10 on my board with respect to AC causing noise/hum? In a perfect world I’d love to not have that be an issue, but I gotta do what I gotta do!

@eriksonderlon 3 года назад

I'm updating my previous reply. I Just turned my rig up loud and with my fuzz and overdrive pedals sitting directly on top of a CIOKS DC10 and there is a slight hum. When I pull the pedals away from the power supply about 6 inches it goes away. Hmmm... :/ I think the DC10 may not be a Switchmode supply because it has a selector for 120v/240v so that would mean there is a transformer in it (it's heavy). Not sure about the AC10 but it too has the switch for 120v/240v.

@VertexEffectsInc 3 года назад

They're great. You can also check out the Truetone CS-12 which does AC and DC.

@VertexEffectsInc 3 года назад

move the power supply away from the pedals and check.

@ransom77 3 года назад

@@VertexEffectsInc awesome, thank you!!

@VertexEffectsInc 3 года назад

@@ransom77 my pleasure!

@martijndebonnet4325 3 года назад

What do you think about Blug's AMP1?

@VertexEffectsInc 3 года назад

Cool if you can’t use a real amp

@RulgertGhostalker 7 месяцев назад

you know what is scary ? ...what if guitar pedal manufacturers start adopting the Euro-Rack standard ??? terrifying really .... but i think kick switches will sort of keep a move like that at bay, because it would be difficult to resolve the potential loads there.

@rumsfield78 Год назад

How do you know if your pedal or tuner has a buffer, and what the range is? Manual?

@VertexEffectsInc Год назад

Manual, or unplug power from it and see if it passes signal when in bypass without power.

@rumsfield78 Год назад

@@VertexEffectsInc I have a Digitech Hardwire poly tuner. I don't think it does. But thanks for the tip. I'll try it out. Btw, I've been hooked on your pods and vids all week. I knew about your pedals, but not your channel. It's awesome!

@wakjob961 3 года назад

I guess 6 people don't like or want FREE help and advice. I also have the Shiva 'Wave' chorus pedal...what's your opinion on it? I've tried in front and in the fx loop. Some days I like it, and some days I miss my MXR 234 ;-(

@VertexEffectsInc 3 года назад

I like it, I also really like the Neunaber Tri Chorus as well for the TSC sound.

@Bushdl85 2 года назад

Boss RC600 as last pedal in the chain, do I need a buffer? I think not?

@VertexEffectsInc 2 года назад

What's the impedance, you should have a guideline here on specs in the video.

@Bushdl85 2 года назад

Thanks for the reply! Output Impedance Main Output: 1 Kilohm Sub Output 1, 2: 1 Kilohm Recommended Load Impedance Main Output: 10 Kilohms Sub Output 1, 2: 10 Kilohms

@primobeltran7955 2 года назад

Do you sell these risers or second tier raise systems?

@VertexEffectsInc 2 года назад

Yes: www.sweetwater.com/c1106--Vertex_Effects--Pedalboards

@newrockorder 7 месяцев назад

footswitch, polytune, noise suppressor.

@SyntheticFuture Год назад

The main two issues I have right now: 1. There's too many interesting pedals 2. Manufacturers use the largest possible housing to make things feel more premium 😶

@VertexEffectsInc Год назад

I haven't found # 2 to be true.

@harumann 3 года назад

1 Tip for a smaller pedalboard: Get a Fractal Audio FM3. And you can even get rid of the heavy and bulky Guitar Amplifier :-)

@VertexEffectsInc 3 года назад

Showering with a raincoat

@waynegram8907 3 года назад

SP400 square plug looks like they are not very FLAT. What other brands or model numbers are very flat or flatter?

@VertexEffectsInc 3 года назад

They're pretty darn flat...any flatter and you'd risk a "short" against the housing.

@user-ok3po8gz4w 3 года назад

Hey everyone.. GO BIG. Buy the biggest pedalboard and put all the pedals lol Yes that is what I am doing right now

@VertexEffectsInc 3 года назад

That’s one way to go for sure!

@jeffc1753 2 года назад

Could you explain the difference between a buffer that has a 100 meg output impedance vs one that has 150 meg? What is the advantage of the 100 meg?

@VertexEffectsInc 2 года назад

Hardly any difference in terms of how well they'll drive capacitance on the output.

@derekdavis8377 3 года назад

What is the controller being used?

@VertexEffectsInc 3 года назад

In the photo? The RJM PBC6X

@XIIMonkeysMusicGroup 3 года назад

I use a lot of EBS Gold cables!

@VertexEffectsInc 3 года назад

Ok...it's fine for consumer level stuff...not a pro option IMO

@XIIMonkeysMusicGroup 3 года назад

@@VertexEffectsInc classist much? I know you're just trying to sell your services and gear, but that couldn't be further from fact! I'm not A-list, but I'm no amateur either!

@VertexEffectsInc 3 года назад

How so? I show how to make the same cables that I sell and my technique for free in several dedicated videos on this channel. I show you the materials, show you the technique, most of the Mogami cable is under $.50 a foot if you buy it in bulk. If that’s not democratizing the information I’m not sure what it is. Perhaps you only have this video to go off of to represent the entire channel, but if you look around our catalog of videos I think you’ll see that we’re pretty good about giving away useful information for free.

@BeantownToBigD 3 года назад

@@VertexEffectsInc ignore the haters - all of them are miserable so they project their negative self images and shortcomings on you. You have a an excellent channel and offer great free advice. Ditto for your podcast it would be great to hear more interviews with pro musicians.

@XIIMonkeysMusicGroup 3 года назад

@@VertexEffectsInc just how you replied is all. Maybe it was typed wrong, but EBS Gold is anything but unprofessional! I also have many pedals that take TRS, and they're often NOT going into or out of other TRS pedals. Also have 4 different types of midi connections in my rig. To set my rig up with all custom soldered cabling (including TRS to TS/RS, Midi, USB--mixed types and sizes!), would be a nightmare! Could some of my EBS be replaced by custom soldered? Sure. But not all! And this is before I get to the pedals in the 2 drawers of my rack! It just sounded like you think that every setup fits into a defined space.

@TheArbiterOfTruth 3 года назад

Small rig: HX Stomp Dual Switch Polytune Mini Dunlop mini volume 🤘🏾

@VertexEffectsInc 3 года назад

No analog is sight!

@kodykindhart5644 3 года назад

😭

@TheArbiterOfTruth 3 года назад

@@VertexEffectsInc my current rig features HX Stomp, BigSky, TimeFactor, Dunlop Mini volume, External aux switch (for the Stomp) eventually I’m going to add a Jackson Audio Asabi, a TC Electronic Polytune Mini 3 and probably a Morningstar MC6

@MK-oz2lf 3 года назад

Hey Mason, off topic. About the T Drive. I don't have it but I saw your December video about it. What if you put a treble booster or a tube screamer in front of the T Drive in a high gain setting? Can it reign in blood?

@VertexEffectsInc 3 года назад

You might have to lower the gain on the pedal to make it work, but yes, it will sound great!

@MK-oz2lf 3 года назад

@@VertexEffectsInc I'll search for one. Thanks man