6.7L Cummins Fuel Injector Replacement

Подписаться 47 тыс.

Просмотров 167 тыс.

50% 1

This video goes over replacing the Fuel Injector on a 6.7L Cummins engine.
Level of Difficulty: Expert
Approximate time: 6 Hours
Tools needed: 8MM Socket, 10MM Socket, 14MM Socket, 15/16 Shallow Socket, 3/8 Ratchet, 19MM Wrench, 3/8 Foot Pound Torque Wrench, 3/8 Inch Pound Torque Wrench, Channel Locks
Vehicle used in this video: 2008 Dodge RAM Cummins 6.7L
The part depicted in this video may fit other vehicle applications, and installations may vary from application to application. Certain vehicles may require different, more or fewer steps. Follow all safety precautions and procedures recommended by the vehicle manufacturer prior to servicing the vehicle. Pay special attention to all warnings and safety systems involved in this repair. Review the disclaimer at the close of this video.
To learn more, visit www.StandardBrand.com

Авто/Мото

Опубликовано:

10 май 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 54

@chancependergrass4384 2 года назад

Just for future viewing reference do not remove the 14mm nut on the rocker arms just remove the 10mm hold down bolt and install new injector torque bolt back down to 27 ft lbs no need for valve adjustment for an injector install unless you just want to

@homeluangaphay2801 2 года назад

Your are correct thanks for pointing that out

@royhanson608 Год назад

Thank you I was like no I need to see that procedure

@Derek-vs9xn 4 месяца назад

Thanks for clarifying I adjusted rockers on SBC but Iam learning about diesels now that I bought a tow truck is it The same time procedure just curious

@bjen2005 Год назад

I think I learned more in that one video then I did in 4 years at high school.

@montuam 3 года назад

Thank You. That was very helpful, there’s a guy at the shop that is very knowledgeable but, He is a pain in the Axx, so instead ask him I prefer doing my search so I can figure out by myself. Excellent video!

@allanjohnson2552 Год назад

This is great, very clear and easy to follow. Now I just have to pinpoint which Injector is bad. That will be tomorrow job.

@ramongallegos2782 Год назад

Thanks for this video and explaining it down to the smallest details

@mr.chadwinter862 2 года назад

Wow good job on explaining it and taking steps detail by detail I’m impressed.

@colinchester390 2 года назад

Excellent, very helpful.

@matthewhahnl7847 3 года назад

Why did you remove the lash setting nut? You only need to remove the center bolt to remove the rocker assembly..

@dpokorzynski 3 года назад

Playing with fire unless you like to reset the overhead.

@PeeDeeFarmer 3 года назад

@@dpokorzynski what you mean

@chrisstidam3006 3 года назад

I was going off of this video cause it was step by step and easy to go off of but I was wondering myself but by the time I figured out I didn't need to it was to late I spun all the nuts off because I'm replacing all injectors. Now I have to gap every rocker and it would be so bad but this video does not show the gapping process or gap specs. This would have been a thumbs way up but now is not

@skinnibwoy 6 дней назад

Thanks. Happy I saw this comment before I started this job

@kathy2148 3 года назад

Great video vary helpful

@joserios4510 2 года назад

After changing then do you have to bleed air out the system if so how

@wrenching5483 2 года назад

My main issue is with a 2012 how do you identify a injector that is causing too much soot. No injector quality test on insite

@homeluangaphay2801 2 года назад

Why did you remove the “exhaust rocker” arm nut #14 mm socket for?

@HamRadio200 2 года назад

Why did you loosen the lash adjustment initially and why didn't you remove the exhaust and intake rockers at the same time?

@rob3454 10 месяцев назад

Great video. Very detailed on all the procedures. Just had a question. What brand of torque wrench you used for this job. I have tried to get both inch lbs and ft lbs 3/8 set but can’t see what’s the brand that have them both. If you have the information I would appreciate it. Thank you

@daveroseberry 2 года назад

Lash specs and process is a very much need to know in this video

@dontcry5829 Год назад

Thanks body, its my 1st time on Cummins and I've no manual for assembling the injectors, that's weird although it's marine engine.

@vajirakantha 3 года назад

Great 👍 Sir very good explanation

@possumpopper89 3 года назад

Question. If I install a rebuilt injector and need to program the ECU for that née injector. Do any of the aftermarket “tuners” enable me to program that into the ECU? I plan to buy a tuner anyway, so if I can do that and avoid paying that money to a local shop to program, it might save me some cash in the overall picture.

@TonyfromAB 2 года назад

Yup

@possumpopper89 11 месяцев назад

@drywall308 the injectors have a number etched into the body. If you install new injectors, the ECU will sometimes throw a trouble code unless you enter the number into the ECU. Turns out my truck ran fine without codes. It already had a tuner installed so it didn’t give me any issues.

@abduolsalamcapo-chichi4157 Год назад

Hou Can i programme the injector

@Giorobot 2 года назад

Do these injectors have to be programmed?

@cumminsmilitia2063 Год назад

Did you have to program them

@steves4639 4 года назад

good vid, thx. It looks like the injector has an indentation for the inlet...how do you ensure the injector is clocked correctly so that the inlet tube lines up with the injector fuel inlet? or maybe the injector just is seated inside a 'chamber' and the fuel inlet tube just injects into the chamber?

@narule2695 2 года назад

Exactly my question

@trevorduhon3617 6 месяцев назад

It simply won’t snap in place, you have to make sure your hole on your injector is facing towards where the tube goes in. before snapping in place

@richardamick1690 7 месяцев назад

Why did you remove the valve lash nut ????

@arieleltana8478 3 года назад

Boa noite amigo...Poderia ligar a legenda ...estou no Brasil

@gilhopkins2465 6 месяцев назад

I am getting a P020D code on my 6.7 Cummins with 99k is an injector?

@chrischapman276 2 года назад

Couldn't the injector have been cleaned and reused?

@tmur2124 Год назад

Excellent video! I have a couple of questions, does the coolant need to be drained and do you need to program the new injector coefficient into the ecm after? Thanks!

@wtbman 10 месяцев назад

I don’t know if that was supposed to be funny or if you’ve only worked on a Powerstroke before. These engines seem so much easier to work on.

@chrischapman276 2 года назад

How did you determine which one needs changing?

@michaelpadfield113 10 месяцев назад

OBD 2 reader will tell you

@brunodiesel267 2 года назад

Gostei, porém quero saber qual o torque dos dois parafusos do bico injetor

@armandoceballos4038 2 года назад

1 step 44 inch lb injector bolts 2 step 11 f lb feed tube nut 3 step 89 inch lb injector bolts 4 step 37 ft lb feed tube nut 5step Rocker arms 27 f lb

@lukesimmons1767 3 года назад

Does anyone know if these torque specs carry over to a 2019? I don’t know what, if anything, has been changed over the years in this area.

@jjames5928 2 года назад

I dont belive its the same torque specs. The 19+ went to a hydraulic valve train so I'm sure other stuff including torque specs has changed

@vicentegonzales3852 5 месяцев назад

No need re program on ecu after replace injectors

@kilianculver9263 5 месяцев назад

You just calibrate the injector codes into the ecm and don't loosen the valve train lock nuts unless you just absolutely want to do an overhead procedure