A1 Heatbed Replacement Tutorial

Подписаться 20 тыс.

Просмотров 5 тыс.

50% 1

Whether you're replacing the heatbed of your Bambu Lab A1 3D printer after the 2024 recall, or have ordered a replacement for another reason, in this video I take you through each of the steps you need to follow for replacing it.
This process is fairly straightforward, but whilst it doesn't involve any soldering, it does involve working with the internal wiring of the printers heatbed, so please take caution whilst doing this, and if you have any uncertainties, please feel free to get in touch with me and/or refer to the official Bambu Labs documentation on printe-bed replacement which you can find here: wiki.bambulab.com/en/a1/maint...
JOIN & SUPPORT ME
---------------------------------------------------
Join this channel to support me and get access to perks:
/ @3drevolution
Perks include: 3D Rev Discord Community, Early access to videos, members discount at the 3D Rev store, and more!
3D REVOLUTION STORE
---------------------------------------------------
www.3DRevolutionStore.com
FOLLOW ME
---------------------------------------------------
Twitter: / the3drev
Facebook: / the3drev
Instagram: / the3drevolution
CHAPTERS
---------------------------------------------------
0:00 - Intro
0:45 - What's included
2:19 - Prepping the printer
2:40 - Remove the old bed
3:19 - Access the bottom
5:42 - Removing wiring
7:14 - The new bed
8:02 - Fitting the new bed
8:44 - Wire in new bed
10:46 - Close it up
12:04 - The final touches

Наука

Опубликовано:

28 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 58

@3DRevolution 2 месяца назад

If you're replacing your heatbed as part of the recall, Bambu Labs will require you to take 3 photos of your updated printer and send them in to receive your gift voucher. Some of those will need to be taken before you fully re-assemble your printer, so please check the email and/or ticket message that Bambu Labs will have sent you to confirm which images they require from you before starting this process. I wasn't able to confirm before posting this video that Bambu Labs was definitely requesting the same images from everyone (rather than varyinig the request slightly to prevent people from just copy and pasting other photos), and as a result didn't specify the photos in the video so as not to misinforrm people. Let me know if you have any issues, and happy printing!

@BennyTygohome 3 месяца назад

I'm beginning this exact process right now 👍😎 we're get the $120 voucher, plus there is a discount 20% coupon code going on right now for the ams light. Perfect timing 😀

@3DRevolution 3 месяца назад

Good luck with the swap over! I was hoping to get this video out sooner than today but unfortunately my kit didn't arrive as soon as expected. Still glad to get it up for people planning to do it over the weekend, hopefully it helps.

@BennyTygohome 3 месяца назад

@@3DRevolutionall done, thank you very much. Your video was excellent. I also made sure i took photos of the connectors and ground wire, etc before screwing the bottom plastic shells back on. BL asked me to send those to ensure it has been done properly and to receive my voucher. Thanks again 👍🎉

@3DRevolution 3 месяца назад

@@BennyTygohome Glad it all went well and great work for taking the pictures. I did mean to include reminders in the video at the relevant points but both couldn't guarantee they would ask the same evidence from everyone (or if they'd vary it slightly to prevent everyone copying photos), and I also forgot until after I'd posted it haha. Happy printing :)

@giovannispagnuolo7715 3 месяца назад

What is the discount code?

@BennyTygohome 3 месяца назад

@@giovannispagnuolo7715 AMS-lite-20-4MC

@BLuNTEDR 3 месяца назад

Awesome job bro, I have 2 of these bad boys and your guide made it a breeze, 100% worth making, so thank you. For anyone doing this from the EU *** MAKE SURE YOU TAKE YOUR PHOTOS *** so that you can get your "compensation".

@3DRevolution 3 месяца назад

Really glad the video was helpful, glad you got your machines back up and running. Very good point about the photos!

@patrickluisi1600 3 месяца назад

I wanted to thank you for taking the time to make such a detailed video! I watched it on Monday April / 22 /2024. And received my new heatbed on Wednesday the 24th Although bamboo did a good job with their video they put out, yours was far more comforting and reassuring. I greatly appreciate it as I'm sure anyone that has done this mod and watched your video will feel the same way thanks again!!! P@t

@3DRevolution 2 месяца назад

Hey Pat, thanks very much I really appreciate it. Glad it helped, happy printing!

@winniegraham1082 3 месяца назад

I want to say, many thanks you for your clear instruction, on how to replace the new A1 Heatbed Tutorial. Great Video! It was, easy step by step all the way to the end! So easy when you know how! I did not take a photo, before and after. But, I have taken a photo side-by-side, you can see clearly, I have replaced the new A1 Bambu HeatBed! Calibrated, and now I am all ready to go! :)

@3DRevolution 2 месяца назад

Great work and really glad the video helped. Happy printing!

@winniegraham1082 2 месяца назад

@@3DRevolution Yes, Many thanks.

@natearrigoni 2 месяца назад

Great video, thank you for the clear instructions. The only thing I would add is to TAKE THE 3 PICTURES FOR YOUR SUPPORT TICKET BEFORE PUTTING THE PANELS ON. It's just the back panel so not a big deal but I forgot.

@3DRevolution 2 месяца назад

Absolutely. I didn't talk about them in the tutorial as I couldn't at the time guarantee that Bambu was requesting the same images from everyone (rather than different sets for different people to avoid people copy and pasting from online) and didn't want to get people to take and send in the wrong images. Glad the video was useful. Thanks very much, and happy printing!

@arranwilliams2523 3 месяца назад

I Already did mine and am printing out the Marbel run for my kids with the bambu recall $$, Spent it all on every kit they sell and also figured id buy all the nozzles a new build plate! cant wait to build stuff again and especially these cool hardware kits!!!!

@3DRevolution 2 месяца назад

Great work, hope the marbel run came out well! Happy printing!

@TheLebbs2001 3 месяца назад

Great video will be running this video again when my bed arrives 👍

@3DRevolution 3 месяца назад

Thanks very much, hope it helps!

@madassmac 3 месяца назад

Thank you very much! Clear and straight forward instructions. Cheers!!

@3DRevolution 2 месяца назад

You're most welcome, glad it was helpful.

@spawnr1 Месяц назад

Thanks for the tutorial!

@johnnenni7134 2 месяца назад

Well, the answer was on Bambu itself saying that printers before such time qualified, so newer ones must have the issue fixed, since I literally just saw it go back up for sale .... like 2 weeks ago i just cancelled my A1 Mini for some reason thinking the A1 was not actually out ... I went to reorder, and boom there it was ....

@3DRevolution 2 месяца назад

Sorry for the late reply. Yes absolutely, as you saw, the A1 was taken off of sale during the recall and it was only put back on sale when they had stock of the A1 fitted with the new heatbed. I'd imagine by now you've received yours, hope you're enjoying it!

@sevensheav 3 месяца назад

Thank you for this clear instruction. My bed arrives tomorrow so i be up and printing Also tomorrow.

@3DRevolution 3 месяца назад

You're welcome! Hope your printer is back up and running!

@helendrew6470 3 месяца назад

Great video! Thanks

@3DRevolution 3 месяца назад

Glad you liked it! Happy printing!

@DavidNightjet 2 месяца назад

Honestly, the best thing to come of this recall is that now if the heatbed were to fail on any unit, even after the warranty ends, there's video documentation on how to replace it. Right to Repair wins again, just like always.

@3DRevolution 2 месяца назад

Hope it was helpful, happy printing!

@rmkcprecima 2 месяца назад

At 8:15 I didn't pay attention to the "slide the bed to the back of the printer" and used the wrong screw holes. Everything worked, I did a calibration then a test print of Benchy. However after a few prints, I kept getting errors that the build plate was missing. I realized that those 4 securing screws I put in the wrong holes so the head bed was 1/4" too far forward. When I saw the head descend down to locate the plate tab, it just missed. As for pictures, bambu emailed back to get me to include my serial number in the shot, only then did they clear my recall message on my printer and process the credit. The manual heat-bed levelling procedure is missing from this instruction. While I ran the file suggested, I didn't watch the video showing the adjustment of the 3 levelling screws until there was a sheet of paper clearance between the head and the head bed without the plate, and the tightening the 2 lock bed screws. The balancing act of the printer on its side scared me, I guessed that it would slide off the box and damage the parts so I used a pillow.

@Glennj08 Месяц назад

Thank you! 🎉❤

@johnnenni7134 2 месяца назад

If I ordered one last night, being that its almost 4AM EST ... And I haven't seen the A1 on the Bambu site, which made me hop to get it when I did .... Does that mean my printer will come with the new Heatbed already fixed? ... I didn't know about the recall, so trying to just find answers

@Mungocomics 2 месяца назад

As someone who just installed the new heat bed, I have a question for you. What should I do with the old heatbed, and is there a safe/proper way to dispose of it?

@3DRevolution 2 месяца назад

This is a good question and I have some thoughts on things people can do with them that I'm working on for a future video so I will revisit this topic. If you did want to get rid of it though, correct disposal methods would depend on where you are and your local services. But there's no dangerous materials or electronics in there, so would be the same process as disposing of a toaster or something like that.

@Martas668 2 месяца назад

I only want to ask, what are the best items to buy from discount we have got after the replacement? Heatbed Nozzle Wiper and Hotend with Nozzle 0.4mm as spare items? Anything else? I am not heavy printer but I know anything can break after some time, but I do not know the weak points of the 3D printers...

@3DRevolution 2 месяца назад

Hey there, sorry for the late reply. Assuming the A1 is the only Bambu Labs printer you have, I'd suggest getting a spare 0.4mm Hardened Steel nozzle, as well as a 0.2mm nozzle and either 0.6mm or 0.8mm. This will give you great flexibility when printing different things (If you're not sure the advantages of different size nozzles, I posted a recent video covering exactly that). Other than that, a spare nozzle wiper is good to have, and beyond that, it's difficult to tell what may be the next thing that needs replacing on the printer, so you'd be best spending the rest of your voucher on possibly an additional build plate, and then as much filament as the voucher will afford you. If you really only wanted to buy spares with the voucher, the next most perishable item in the A1 would be the belts, so you could invest in one of each of them. Hope that helps (if you've not already spent your voucher), and again, sorry for the late reply.

@mdbjorklund 3 месяца назад

Did those of you who have received your replacement get any notice that it was being shipped to you or did it just arrive without notice? I haven't heard anything...

@3DRevolution 3 месяца назад

I personally received 2 updates via email (one that it was coming soon, and one when it was actually dispatched), followed by an update to my ticket. If you've not heard anything yet, possibly send a message replying to your existing ticket which you'd requested the replacement on?

@PlastiBots 3 месяца назад

Got a shipping notice both from my ticket on BL as well as FedEx tracking

@mdbjorklund 3 месяца назад

@@3DRevolution Thanks! I got notified as well and received my heat bed today.

@dooha333 3 месяца назад

Thank you for the informative video. Do you know if the check by an electrically skilled person is required in the UK to get the voucher? Or this only in the EU?

@3DRevolution 3 месяца назад

You're welcome RE the video. No need for getting it checked over in the UK, this is only the EU. However, Bambu does require you to send them a set of pictures to prove that you've completed the bed replacement correctly before they issue the voucher. They should have sent you an email and/or ticket update letting you know what photos they wanted. I would have included it in the video but I'm not 100% sure it will be the same photos requested for everyone as they may vary it to prevent people just using other people's photos. For me it was a photo of the re-fitted ground cable, a photo of the sensor wires held down with tape, and a photo of the back of the printer with the end-stop fitted and the serial number QR code in frame.

@grougan 2 месяца назад

Did anyone need to perform bed tramming after installing the new heatbed, or was there no need?

@Martas668 2 месяца назад

I skipped it... I only did quick bed leveling when printing something and it was ok.

@3DRevolution 2 месяца назад

I ran several test prints of different styles after recording this video to ensure it was printing well before editing and publishing it as I wanted to double check tramming wasn't required. I had presumed it wouldn't need it with the level of automated calibration it does anyway and it was fine for me. That said, I have seen a couple of people say they needed to do it, but I am not sure if that was a precautionary judgement on their part, or they found it to be necesary after experiencing issues. If enough people comment requesting a bed tramming tutorial, I'll make one and link to it in the video description.

@llmgmll 2 месяца назад

And why don't you show the manual bed levelling?

@3DRevolution 2 месяца назад

I'm guessing you mean bed tramming. Well I had assumed that it wouldn't be necesary as a result of the level of callibration it does when running full calibration. However I didn't want to just publish a tutorial based on an assumption, so I ran and completed several prints checking everything ran fine after replacing the bed before editing and publishing this video, and it worked perfectly. I didn't want to add another step for people to work through if it wasn't necesary so didn't include it as a section in this video. I've had a couple of people ask if it's necesary, but I don't think I've had anyone yet say that they found it was necesary.

@rudetoons7906 2 месяца назад

I wish someone would explain how to disconnect the AMS filament tubes correctly :/

@3DRevolution 2 месяца назад

As in, removing the PTFE tubes from the AMS itself, or from the 4 way splitter on the extruder?

@rudetoons7906 2 месяца назад

@@3DRevolution both ^^ but i did it, its was by far my biggest issue because i wasnt sure if i had to pull or push it (push both down), they were pretty hard to remove.

@yasin_uyghur 3 месяца назад

I am still waiting A1 …🙂‍↕️

@3DRevolution 3 месяца назад

As in you're waiting for the A1 to come on sale again or you're still waiting for your new heatbed to arrive?

@yasin_uyghur 3 месяца назад

@@3DRevolution Yes I’m waiting for A1 to coming on sale

@3DRevolution 3 месяца назад

@@yasin_uyghur I'd imagine it should be re-released in the next 2-3 weeks. Fingers crossed.

@maythemighty5183 2 месяца назад

Wow that cable looks cheaper 😅🤦🏻‍♂️🤷🏻‍♂️ oh well. Guess ill just install it

@3DRevolution 2 месяца назад

It's more flexible so better suited to the task, I think it was the right decision. They could have absolutely replaced it with a natively braded cable, but this is a method they'd already employed with the Z/Y axis cable, and so it's already been heavily tested. If they switched to a whole new design, they'd be introducing a realtive unknown, so this was the safer option for both them and the consumers.