Waiting for a Fesh one to be delivered this evening. Can't wait to see what i can modify etc. The Felony release and follow-up era was the best of RC RU-vid, it will take me a year to watch all these Arrma Felony videos. I was hoping and waiting for a Year Three Update, but Arrma didn't announce anything so i went ahead and bought one.
You have to change C block and d block. Which are the holes on the inside hinge pins. Search scorched rc website for 0 degree c block or d block. Or pps website or eBay for the unit.
You see on my felony there’s wabble on the rear and a little on the front what spacers could I could get to stop it and where exactly would I out them! Good video to
I'm not understanding exactly what you are saying. I have slight wibble wobble in mines too. You can use spacers such as washers to place in between the the c hub and a arm front and rear to reduce the wheels from sliding from to back. Use heat shrink around the metal ball that sits inside all the linkages. That would reduce alot of slop. Still you're going to have wheel wobble and that is something you're going to have to figure out.
This location is way too far to do a speed run for me, lol.... Only 867 feet , to get to top speed is not enough room. I reached out to TipTon, they claim the airport is busy, LOL . I live in that area, When I drive that way I have never seen an airplane take off or land, or even go close to it. I also fly a drone, and I don't see any activity at that airport. I almost had a deal at Brockbridge road airport, but people started to drag race their vehicles on the runway, and they fenced it in and put dirt mounds out. That was 2937 foot long, good length to go full throttle. I actually met with one of the owners, and spoke with him. Too bad they ruined that.
@@MatrixRC Kembo is the best spot for now. I will be moving soon. So I will go out their when the weather is 65 or better. I have done a few runs in the last month on good days. cold is just not good for speed runs, even with foam tires.
@@JasonGunn418 yea cold Temps makes it hard for any tires to get traction. Some people prep them but the prep is gone as soon as they go a few feet. Well wherever you're headed be safe and look up some nice spots. I always do that when I travel and take my speed run car.
Please help and suggest I am confused and unable to make decision between Felony Vs Infraction. Felony looks so awesome and tempting but has rear tires and different differentials whereas Infraction is same platform all rounder with okish looks. Please help whether I should go with Felony or infraction if I consider drivability,maintenance and speed run
At this time of making the video I don't remember what he did but I can tell you that it's possible to replace the diff with the Infraction v2 diffs. But you don't even have to do that. I have a build video on my channel showing and telling in depth of the Arrma Felony check it out.
Check the parts to the drive shaft in my description where you can pick them up. And just set you angle up where the driveshaft are level and straight across bud. All that was said in the video.
Make sure you adjust your tires camber to 0° and make sure your steering trim is centered. In addition, make sure your shocks are properly set on all four wheels. If you notice your car pulling to one side when you on throttle that could be caused by a lot of things. To much to say on here. Just message me on Instagram @MatrixRC28
Raz Shifrin recently showed how'd to do it. Check out the link here for his 150mph build. He does a better job at explaining it. I follow him and we share info and ideas. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3-yJh6c-JQ8.html
Remove the center diff. Remove the rear driveshaft. Unscrew the rear support brace and lift up. And joila lift up the speed balancer. And put back together in reverse.👍🏽💯
I don't have spikes on mines. And I don't know where Ghozt Rc 202 got them but if you google search Wheel hex spikes for Arrma infraction something should pop up.